HOOKE ROAD 18-20 F150 Discovery Rear Bumper with LED Floodlights Instruction Manual
- May 15, 2024
- HOOKE ROAD
Table of Contents
HOOKE ROAD 18-20 F150 Discovery Rear Bumper with LED Floodlights
Product Information
Specifications:
- Model: BXG.8251-S
- Contents:
- 10 Hex Bolt (M12*35)
- 10 Split Lock Washer (D12)
- 20 Flat Washer (M12302)
- 10 Hex Nut (M12)
Tools Required:
- a. Drive Socket Ratchet Wrench
- b. 19mm Wrench
- c. 19mm Shallow Socket
Installation Time:
About 1 hour, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.8251-S), please scan the QR code.
Installation Instructions:
- Step 1: Remove the factory rear bumper, ready to install Hooke Road rear bumper.
- Step 2: Assemble the left wing, right wing & the main body with the provided hardware.
- Step 3: Install the bracket on the car with the screws of the factory vehicle trailer hook.
- Step 4: Assemble the bracket & the rear bumper with the provided hardware. Adjust height and tighten bolts.
- Step 5: The installation is complete. Enjoy your off-road adventures with this Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any questions about your purchase.
Hooke Road to find your parts
FAQ
Q: How do I adjust the height of the bumper during installation?
A: To adjust the height of the bumper, loosen the bolts on both sides of the bumper, position it at the desired height, and then tighten the bolts securely.
Q: Can I install this rear bumper alone?
A: While it’s recommended to have 2-3 people for installation, it is possible to install the rear bumper alone if you have experience with similar installations.
Contents
Tools required
- a. Drive Socket Ratchet Wrench;
- b. 19mm Wrench;
- c. 19mm Shallow Socket;
Installation time
About 1 hour, 2-3 people may be needed. Installation time may differ according
to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.8251-S), please scan the QR code.
Installation instruction
- Step 1: Remove the factory rear bumper, ready to install hooke road rear bumper.
- Step 2: Assemble the left wing, right wing & the main body with the Hex Bolt (M1235), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nut (M12).
- Step 3: Install the bracket on the car with the screws of the factory vehicle trailer hook.
- Step 4: Assemble the bracket & the rear bumper with the Hex Bolt (M1235), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nut (M12).
- Tighten up the bolts on both sides after adjusting the height of the bumper. Leave a proper distance between the bumper and the car frame.
- Step 5: The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!
Attention
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Hooke Road to find your parts
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>