HOOKE ROAD BXG.3054 JL Fender Flares Armor Style Front and Rear Kit Installation Guide

HOOKE ROAD BXG.3054 JL Fender Flares Armor Style Front and Rear Kit

Specifications :

• Model : BXG.3054
• Contents :
  • 2 Button Head Socket Cap Bolts Screws (M8*20)
  • 8 Button Head Socket Cap Bolts Screws (M6*20)
  • 8 Split Lock Washer
  • 2 Flat Washer (D6 M8161)
  • 8 Flat Washer (M6161)
  • 6 Flange Hex Lock Nuts (M6)
  • 2 Flange Hex Lock Nuts (M8)
  • 2 Rivet Nut (M6)
  • 2 Rubber Strip

Product Usage Instructions

Tools Required:

• Drive Socket Ratchet Wrench
• 4mm & 5mm Hex Bit Socket
• Rivet Nut Tool
• 10mm & 13mm Wrench
• Hand Rivet Nut Tool (Package Included)

Installation Time:
About 1 hour, 2-3 people may be needed. Installation time may differ according to your mechanical skill level. Please verify all parts are present and read instructions carefully before starting installation.

Installation Instructions:

1. 1. Remove the factory front fender flare.

2. Apply rubber strips along the edges of the fender to prevent scratching the car surface.
3. Install the rivet nut in the most right hole using the rivet nut tool.
4. Lift up the front fender flare and install the bolts in sequence.
5. Complete installation on both driver and passenger sides.

Lighting Wiring Installation:
The fender flares light have the functions of the Turn lamp. Connect the wiring harness as instructed.

Attention:

1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
2. Contact your distributor for any questions about your purchase.

FAQ:

1. Q: How do I know if I have installed the front fender flares correctly?
   A: Ensure all bolts are securely tightened, and the fender flares are aligned properly with the vehicle’s body.

2. Q: Can I install the front fender flares alone?
   A: While it is recommended to have 2-3 people for installation, it is possible to install them alone with the proper tools and precautions.

Front Fender Flares
BXG.3054

Tools required

• Drive Socket Ratchet Wrench;
• 4mm & 5mm Hex Bit Socket;
• Rivet Nut Tool;
• 10mm & 13mm Wrench;

Installation time

• About 1 hour, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
• (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
• To view the electronic version (BXG.3054), please scan the QR code.

Installation instruction

Driver Side Front Fender Flare Installation：
Step 1 : Remove the factory front fender flare. Ready to install our product.

Step 2: Before installation, please apply rubber strips along the edges of the fender (green line) to prevent scratching the car surface.

Step 3 : Install the rivet nut in the most right hole with the rivet nut tool. the rivet nut tool instruction  The 4mm Hex Bit Socket use in the top, 10mm wrench stuck on the middle nut. Put the rivet nut in the hole, screw the threaded end of the rivet nut tool into the rivet nut (Notice: Must be screwed to the bottom), finally unscrew the rivet nut tool out.

Step 4: Next, Lift up the front fender flare and install the left two holes. Use the Button Head Socket Cap Bolts Screws (M820) groups and Button Head Socket Cap Bolts Screws (M620) groups. Don’t tighten up those bolts.

Step 5: And then install the middle two holes. Use the Button Head Socket Cap Bolts Screws (M6*20) groups. Don’t tighten up those bolts.

Step 6: Finally, when installing the rightmost hole, use the extended rod tool to screw in the screw, and then cover the plug back. 

Step 7: After completing the driver side installation, follow the same installation method on the passenger side.
Lighting Wiring Installation:

Installation: Find the factory fender flares light wiring harness. Connect the wiring harness as follows.
Negative Electrode (Black Wire) – Factory Black Wire Turn Lamp (Red Wire)-Factory White Yellow Wire
Notes: Different models may have different wiring harness colors, but the above wiring methods are the same.

Step 8:
The installation is complete. We hope you enjoy a wonderful off-road life with this quality Hooke Road product!

Attention:

1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
2. Please feel free to contact your distributor if you have any kind of question about your purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>