HOOKE ROAD BXG.9027 Front Bumper Instruction Manual
- May 15, 2024
- HOOKE ROAD
Table of Contents
MAKE A DIFFERENCE
FrontBumper
BXG.9027
Contents:
| Qty | Part Name | Size (mm) | Picture |
|---|---|---|---|
| 12 | Hex Bolt | M12*30 | |
| 4 | Hex Bolt | M12*140 | |
| 6 | Hex Bolt | M8*20 | |
| 4 | Button Head Socket Cap Bolts Screws | M6*20 | |
| 16 | Split Lock Washer | D12 | |
| 6 | Split Lock Washer | D8 | |
| 20 | Flat Washer | M12302 | |
| 6 | Flat Washer | M8161.5 | |
| 4 | Flat Washer | M6121 | |
| 16 | Hex Nuts | M12 | |
| 6 | Flange Hex Lock Nuts | M8 | |
| 4 | NylonI nsert Lock Nut | M6 | |
| 2 | Nylon Round Spacer | M6121.3 | |
| 2 | EVA |
Tools required:
a. Drive Socket Ratchet Wrench;
b. 4mm Hex Bit Socket;
c. 10mm, 13mm, 19mm Wrench;
d. 10mm, 13mm, 19mm Shallow Socket;
Installation time:
About 1.5 hours, 2-3 people may be needed. Installation time may differ
according to your mechanical skill level.
(PLEASE VERIFY ALL PARTS ARE PRESENT AND READ INSTRUCTIONS CAREFULLY BEFORE
STARTING INSTALLATION!)
To view the electronic version (BXG.9027), please scan the QR code.
https://drive.google.com/drive/folders/1nWb6LOEjGfIkPvH7VAzAwCvlqrA0x-
ZE?usp=sharing
Installation instruction:
Step 1: Remove the factory front bumper, ready to install our product.
Step 2: Stick the EVA into the main body. To assemble the wings & the main body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12). Repeat the same installation in the other side.
Step 3: To install the bull bar into the main body. Use the Hex Bolts (M820), Split Lock Washer (D8), Flat Washer (M816*1.5), Flange Hex Lock Nuts (M8).
Step 4: Assemble the license plate bracket (A1, A2, A3) with the M620 button head socket cap bolts screw groups. And then install it into the bumper with the M620 button head socket cap bolts screw groups.
Step 5: To install the winch power control box bracket. Use the Hex Bolts (M820), Split lock washer (D8), Flat washer (M816*1.5), Flange Lock Hex Nuts (M8). This step isn’t 100% necessary. Depends if you have the winch power control box.
Step 6: To install the mounting brackets to the main body. Use the Hex Bolts (M1230), Split Lock Washer (D12), Flat Washer (M1230*2), Hex Nuts (M12). Don’t tighten up those bolts.
Step 7: Install the bumper into your vehicle with the Hex Bolt(M12140), Split Lock Washer(D12), Flat Washer(M1230*2), Hex Nuts(M12).
Step 8: Keep the bolts loose, raise the bumper, adjust the gap between it and the car, and then tighten the step 6 & step 7 bolts after confirming that the desired effect is achieved.
Step 9:
The installation is complete. We hope you enjoy a wonderful off-road life with
this quality Hooke Road product!
Attention:
- The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
- Please feel free to contact your distributor if you have any kind of question about your purchase.
Hooke Road to find your parts.
Feel Free To Share Your Vehicle @HookRoad 4 x 4
With The Hashtag #hookeroad If You’d Like
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>