HOOKE ROAD BXG.8909-S Bronco Offroad Rear Bumper Rings LED Light Instruction Manual

May 15, 2024
HOOKE ROAD

HOOKE ROAD BXG.8909-S Bronco Offroad Rear Bumper Rings LED Light

HOOKE ROAD BXG.8909-S Bronco Offroad Rear Bumper Rings LED
Light

Contents

Contents
Contents

Qty Part Name Size(mm) Picture
4 Hex Bolt M12*45 ****
4 Split Lock Washer D12 ****
4 Flat Washer M121.53 0 ****
4 Button Head Socket Cap Bolts Screws M4*16 ****
4 Socket Head Cap Screws M6*16 ****
4 Split Lock Washer D6 ****
4 Flat Washer M6161 ****
4 Flange Hex Lock Nuts M6

Tools required

a. 13mm, 18mm, 19mm Wrench;
b. Push pin remover tool;
c. Electrical tape;

Installation time

About 2 hours, 2-3 people may be needed. Installation Time May Differ According to your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT ANDREADINSTRUCTIONSCAREFULLY BEFORE STARTING INSTALLATION!)

To view the electronic version (BXG.8909-S), please scan the QR code
QR code

Installation instruction

Step 1: Unplug the factory bumper from the Bronco. Located the small plugs just to the rear of wheel wells on each side of the bumper.
Installation instruction
Step 2: Using a 13mm Socket, unbolt the side bumper support so each side of the bumper just outside of the frame rails.
Installation instruction
Step 3: Remove the lower four bumper bolts using 18mm Socket.
Note: When you do this, the bumper can become free from th evehicle and can fall. Ensure you have another person holding it, or the bum per secure to prevent falling and injury.
Installation instruction
Step 4: Once bumper is removed, lay on soft surface facedown. Unclip the license plate light by squeezing the plug and pulling away from the bumper.
Installation instruction
Step 5: Remove the thirteen bolts holding the three center brackets using a 13mm socket.

Step 6: Using a push pin removal tool, remove point where the wire harnesses connected to the bumper or brackets.
Installation instruction
Step 7: Remove the two center sensors from the sensor bezels by spreading the two tabs on the bezels and pull the sensor up.
Installation instruction
Step 8: To remove the outer sensor, spread the tabs on the inner gray sensor bezel to release the senor, and once removed, squeeze the same tab while pulling the face of the bezel on the outside to release the bezel from the white cage.
Installation instruction
Step 9: Lean the bumper forward, and while pulling the face of sensor bezel from the outside of the bumper, squeeze the two tabs on the bezel near the bumper to the remove the bezel.
Installation instruction
Step 10: Carefully. Pull the wire harness away to be used on you new bumper. You are now done with the removal of your bronco bumper.

Step 11: Install the left & right extension part into the bumper with the Socket Head Cap Screws (M616), Split Lock Washer (D6), Flat Washer (M6161), Flange Hex Lock Nuts (M6).
Installation instruction
Step 12: Lay the factory wire harness across the bumper lining up the sensor to the corresponding holes. running the wire harness though the bumper’s structure. Install the sensor into your bumper with the Button Head Socket Cap Bolts Screws (M4
16).First put the rubber stopper into the sensor, and then install the bracket of the sensor.
Installation instruction
Step 13: Lift up the bumper into the vehicle frame. Install the bumper with the Hex Bolt (M1245), Flat Washer (M121.5*30), Split Lock Washer (D12),Hex Nuts (M12) . (Can also be installed with factory bolts).
Installation instruction
Step 14: Install the D-rings into the bumper.
Step 15: The installation is complete. We hope you enjoy a wonderful off- road life with this quality Hooke Road product!
Installation instruction
Attention

  1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation of the product.
  2. Please feel free to contact your distributor if you have any kind of question about your purchase.
    Hooke Road to find your parts

@HookRoad4x4
Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

HOOKE ROAD User Manuals

Related Manuals