IRFP150 Vishay Siliconix Discrete Semiconductor Instructions

IRFP150 Vishay Siliconix Discrete Semiconductor

PRODUCT SUMMARY

PRODUCT SUMMARY

VDS (V)| 100
RDS(on) (W)| VGS = 10 V| 0.055
Qg (max.) (nC)| 140
Qgs (nC)| 29
Qgd (nC)| 68
Configuration| Single

FEATURES

• Dynamic dV/dt rating
• Repetitive avalanche rated
• Isolated central mounting hole
• 175 °C operating temperature
• Fast switching
• Ease of paralleling
• Simple drive requirements
• Material categorization: for definitions of compliance please see www.vishay.com/doc?99912.

Note
This datasheet provides information about parts that are RoHS-compliant and/or parts that are non-RoHS-compliant. For example, parts with lead (Pb) terminations are not RoHS-compliant. Please see the information/tables in this datasheet for details.

DESCRIPTION

• Third-generation Power MOSFETs from Vishay provide the designer with the best combination of fast switching, ruggedized device design, low on-resistance, and cost-effectiveness.
• The TO-247AC package is preferred for commercial-industrial applications where higher power levels preclude the use of TO-220AB devices. The TO-247AC is similar but superior to the earlier TO-218 package because its isolated mounting hole. It also provides greater creepage distances between pins to meet the requirements of most safety specifications.

ORDERING INFORMATION

ORDERING INFORMATION

Package| TO-247AC
Lead (Pb)-free| IRFP150PbF

ABSOLUTE MAXIMUM RATINGS

ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless otherwise noted)

PARAMETER| SYMBOL| LIMIT| UNIT
Drain-source voltage| VDS| 100| V
Gate-source voltage| VGS| ± 20
Continuous drain current| VGS at 10 V| TC = 25 °C| ID| 41|

A

TC = 100 °C| 29
Pulsed drain current a| IDM| 160
Linear derating factor|  | 1.5| W/°C
Single pulse avalanche energy b| EAS| 830| mJ
Repetitive avalanche current a| IAR| 41| A
Repetitive avalanche energy a| EAR| 19| mJ
Maximum power dissipation| TC = 25 °C| PD| 230| W
Peak diode recovery dV/dtc| dV/dt| 5.5| V/ns
Operating junction and storage temperature range| TJ, Tstg| -55 to +175| °C
Soldering recommendations (peak temperature)| for 10 s|  | 300d
Mounting Torque| 6-32 or M3 screw|  | 10| lbf · in
1.1| N · m

Notes

• a. Repetitive rating; pulse width limited by maximum junction temperature (see Fig. 11)
• b. VDD = 25 V, starting TJ = 25 °C, L = 740 μH, Rg = 25 Ω, IAS = 41 A (see fig. 12)
• c. ISD ≤ 41 A, dI/dt ≤ 300 A/μs, VDD ≤ VDS, TJ ≤ 175 °C
• d. 1.6 mm from the case

THERMAL RESISTANCE RATINGS

THERMAL RESISTANCE RATINGS

PARAMETER| SYMBOL| TYP.| MAX.| UNIT
Maximum junction-to-ambient| RthJA| –| 40|

°C/W

Case-to-sink, flat, greased surface| RthCS| 0.24| –
Maximum junction-to-case (drain)| RthJC| –| 0.65

SPECIFICATIONS

SPECIFICATIONS (TJ = 25 °C, unless otherwise noted)|
---|---
PARAMETER| SYMBOL| TEST CONDITIONS| MIN.| TYP.| MAX.| UNIT|
Static|
Drain-source breakdown voltage| VDS| VGS = 0 V, ID = 250 μA| 100| –| –| V|
VDS temperature coefficient| DVDS/TJ| Reference to 25 °C, ID = 1 mA| –| 0.14| –| V/°C|
Gate-source threshold voltage| VGS(th)| VDS = VGS, ID = 250 μA| 2.0| –| 4.0| V|
Gate-source leakage| IGSS| VGS = ± 20 V| –| –| ± 100| nA|
Zero gate voltage drain current| IDSS| VDS = 100 V, VGS = 0 V| –| –| 25| μA|
VDS = 80 V, VGS = 0 V, TJ = 150 °C| –| –| 250
Drain-source on-state resistance| RDS(on)| VGS = 10 V| ID = 25 A b| –| –| 0.055| W|
Forward transconductance| gfs| VDS = 25 V, ID = 25 A b| 13| –| –| S|
Dynamic|
Input capacitance| Ciss| VGS = 0 V, VDS = 25 V,

f = 1.0 MHz, see fig. 5

| –| 2800| –|

pF

|
Output capacitance| Coss| –| 1100| –
Reverse transfer capacitance| Crss| –| 280| –
Total gate charge| Qg|

VGS = 10 V

|

ID = 41 A, VDS = 80 V,

See Fig. 6 and 13 b

| –| –| 140|

nC

|
Gate-source charge| Qgs| –| –| 29
Gate-drain charge| Qgd| –| –| 68
Turn-on delay time| td(on)|

VDD = 50 V, ID = 41 A,

Rg = 6.2 W, RD = 1.2 W, see fig. 10 b

| –| 16| –|

ns

|
Rise time| tr| –| 120| –
Turn-off delay time| td(off)| –| 60| –
Fall time| tf| –| 81| –
Internal drain inductance| LD| Between lead,|  | |  | –| 5.0| –|  |
6 mm (0.25″) from the package and center of the die contact

| | nH|

Internal source inductance

|

LS

|

–

|

13

|

–

Drain-Source Body Diode Characteristics|
Continuous source-drain diode current| IS| MOSFET symbol|  |  | | –| –| 41|  |
showing the integral reverse p – n junction diode

| | A|
Pulsed diode forward current a| ISM|

–

|

–

|

160

Body diode voltage| VSD| TJ = 25 °C, IS = 41 A, VGS = 0 V b| –| –| 2.5| V|
Body diode reverse recovery time| trr| TJ = 25 °C, IF = 41 A, dI/dt = 100 A/μs b| –| 220| 330| ns|
Body diode reverse recovery charge| Qrr| –| 1.9| 2.9| μC|
Forward turn-on time| ton| Intrinsic turn-on time is negligible (turn-on is dominated by LS and LD)|

Notes

• e. Repetitive rating; pulse width limited by maximum junction temperature (see Fig. 11)
• f. Pulse width ≤ 300 μs; duty cycle ≤ 2 %

TYPICAL CHARACTERISTICS

TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)

Peak Diode Recovery dV/dt Test Circuit

Vishay Siliconix maintains worldwide manufacturing capability. Products may be manufactured at one of several qualified locations. Reliability data for Silicon Technology and Package Reliability represent a composite of all qualified locations. For related documents such as package/tape drawings, part marking, and reliability data, see www.vishay.com/ppg?91203.

Package Information

TO-247AC (High Voltage)

VERSION 1: FACILITY CODE = 9

 | MILLIMETERS|
---|---|---
DIM.| MIN.| NOM.| MAX.| NOTES
A| 4.83| 5.02| 5.21|
A1| 2.29| 2.41| 2.55|
A2| 1.17| 1.27| 1.37|
b| 1.12| 1.20| 1.33|
b1| 1.12| 1.20| 1.28|
b2| 1.91| 2.00| 2.39| 6
b3| 1.91| 2.00| 2.34|
b4| 2.87| 3.00| 3.22| 6, 8
b5| 2.87| 3.00| 3.18|
c| 0.40| 0.50| 0.60| 6
c1| 0.40| 0.50| 0.56|
D| 20.40| 20.55| 20.70| 4
D1| 16.46| 16.76| 17.06| 5
---|---|---|---|---
D2| 0.56| 0.66| 0.76|
E| 15.50| 15.70| 15.87| 4
E1| 13.46| 14.02| 14.16| 5
E2| 4.52| 4.91| 5.49| 3
e| 5.46 BSC|
L| 14.90| 15.15| 15.40|
L1| 3.96| 4.06| 4.16| 6
Ø P| 3.56| 3.61| 3.65| 7
Ø P1| 7.19 ref.|
Q| 5.31| 5.50| 5.69|
S| 5.51 BSC|

Notes

1. Package reference: JEDEC® TO247, variation AC
2. All dimensions are in mm
3. Slot required, notch may be rounded
4. Dimensions D and E do not include mold flash. Mold flash shall not exceed 0.127 mm per side. These dimensions are measured at the outermost extremes of the plastic body
5. Thermal pad contour optional with dimensions D1 and E1
6. Lead finish uncontrolled in L1
7. Ø P to have a maximum draft angle of 1.5° to the top of the part with a maximum hole diameter of 3.91 mm
8. Dimensions b2 and b4 do not include dambar protrusion. Allowable dambar protrusion shall be 0.1 mm total above b2 and b 4 dimension at maximum material condition

VERSION 2: FACILITY CODE = Y

 | MILLIMETERS|
---|---|---
DIM.| MIN.| MAX.| NOTES
A| 4.58| 5.31|
A1| 2.21| 2.59|
A2| 1.17| 2.49|
b| 0.99| 1.40|
b1| 0.99| 1.35|
b2| 1.53| 2.39|
b3| 1.65| 2.37|
b4| 2.42| 3.43|
b5| 2.59| 3.38|
c| 0.38| 0.86|
c1| 0.38| 0.76|
D| 19.71| 20.82|
D1| 13.08| –|
D2| 0.51| 1.30|
---|---|---|---
E| 15.29| 15.87|
E1| 13.72| –|
e| 5.46 BSC|
Ø k| 0.254|
L| 14.20| 16.25|
L1| 3.71| 4.29|
Ø P| 3.51| 3.66|
Ø P1| –| 7.39|
Q| 5.31| 5.69|
R| 4.52| 5.49|
S| 5.51 BSC|

Notes

1. Dimensioning and tolerancing per ASME Y14.5M-1994
2. The contour of the slot optional
3. Dimensions D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005″) per side. These dimensions are measured at the outermost extremes of the plastic body
4. Thermal pad contour optional with dimensions D1 and E1
5. Lead finish uncontrolled in L1
6. Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154″)
7. Outline conforms to JEDEC outline TO-247 with the exception of dimension c

VERSION 3: FACILITY CODE = N

ECN: E22-0452-Rev. G, 31-Oct-2022 DWG: 5971

Notes

1. Dimensioning and tolerancing per ASME Y14.5M-1994
2. The contour of the slot optional
3. Dimensions D and E do not include mold flash. Mold flash shall not exceed 0.127 mm (0.005″) per side. These dimensions are measured at the outermost extremes of the plastic body
4. Thermal pad contour optional with dimensions D1 and E1
5. Lead finish uncontrolled in L1
6. Ø P to have a maximum draft angle of 1.5 to the top of the part with a maximum hole diameter of 3.91 mm (0.154″)

Legal Disclaimer Notice

Disclaimer
ALL PRODUCTS, PRODUCT SPECIFICATIONS, AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION DESIGN, OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any liability for any errors, inaccuracies, or incompleteness contained in any datasheet or in any other disclosure relating to any product.

Vishay makes no warranty, representation, or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any liability arising out of the application or use of any product, (ii) any liability, including without limitation special, consequential, or incidental damages, and (iii) any implied warranties, including warranties of fitness for a particular purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein.

Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. The inclusion of these hyperlinks does not constitute an endorsement or approval by Vishay of any of the products, services, or opinions of the corporation, organization, or individual associated with the third-party website. Vishay disclaims all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>