Forsafe YW-0629 Digital Wireless Camera System User Manual
- June 8, 2024
- Forsafe
Table of Contents
Forsafe YW-0629 Digital Wireless Camera System
Digital Wireless Camera System SPLIT VIEW FOR ( 2) CAMERA
Normally you do not need to pair the camera and monitor, we defaulted and
paired them well to the first channel before delivery. What you need to do are
as follows:
- Find out the installation place of the camera and the power of reversing light( or ACC).
- Install the monitor to a suitable place and connect it to the cigarette lighter.
Package contents
- Wireless camera x 1
- 5″ wireless monitor x 1
- Mount Bracket x 1
- Antenna x 2
- Screw Kit for Camera Installation x 1
- Camera Power Cable x 1
Installation
- An electric shock or product malfunction may occur if this product is installed incorrectly.
- Use this product within the voltage range specified. Failure to do so can cause electronic shock or product malfunction.
- Take special care when cleaning the monitor, no wet hands touch it during installation.
- Make sure to firmly affix the product before use.
- If smoke or a burning smell is detected, disconnect the system immediately.
- Where the power cable may touch a metal case, cover the cable with friction tape.
- A short circuit or disconnected wire may cause a fire.
- While installing the System be careful with the wire positioning in order to avoid wire damage.
- Do not watch movies or operate the monitor while driving; as it may cause an accident.
- Do not install the monitor where it may obstruct the driver’s view or obstruct an airbag device.
- Dropping the unit may cause possible mechanical failure.
- Do not hard press the camera lens.
- Do not crush or damage the power cable.
- Do not use the device during a lightning storm.
Operating Precautions
- The device may be powered by a 12/32 volt battery or the vehicle’s electrical system.
- Make sure all cables are connected properly. Improper cable connections may damage the monitor. Remove the power cable connections when not using the device.
FAQ
-
Is the signal between the camera and the receiver encrypted?
Yes. -
How many cameras does the system support?
2 cameras. -
Why does the frame rate sometimes drop when I am driving?
When driving the signal reception might drop sometimes. This occurs as the signal to the receiver is constantly transmitted from different angles. This is considered normal when transmitting wirelessly. -
Is the camera water-resistant?
The camera is Ip69k classed. This means that the camera is well protected from both dust and humidity. It can be placed outside and can be cleaned using a pressure washer. -
Can I hear sound from the camera?
No, the camera does not have a microphone. -
I am using the camera for reversing, how do I mirror the image?
Please see the instructions in the “Operation” section. -
What do I do if I have bad reception on the LCD monitor?
Start by reading through the troubleshooting. If troubleshooting doesn’t help, welcome to contact us: -
Will the camera break at very low temperatures?
No, at very low temperatures the picture might tone red. At extremely low temperatures the camera might turn off. However, when the temperature gets higher again the camera will regain its functionality.
Picture-Image Settings
The image can be modified to the driver’s specifications. Easily adjust the Brightness, Contrast, and Color to create the optimal brightness.
- Press “ Menu”
- Press “ / ” & “OK ” to Select “ Picture “
- Press “ OK” & “ / ” to adjust the picture image settings
Mir-flip Screen Rotation Settings
System – Settings
- Press “ Menu ”, Choose“SYSTEM” and Press “ OK”
- Press “ / ” to adjust
- Press “ OK ” to select
- Language: Language Selection
- Delay time: Interval Time when reversing camera displays
- Scantime: Interval time when auto scan is on
- Autoscan: Auto displays CH1 & CH2 on/off
- Autoscan means system displays CH1 & CH2 by turns
Technical Specification
Monitor
- Monitor Panel Size 5″ LED Digital Panel
- Video System PAL/NTSC auto
- Resolution 800 x 3(RGB) x 480
- Brightness 500cd/m2
- Contrast Ratio 500:1
- Screen Mode 16:9
- Field of View Top: 50°, Botiom 70°, L/R 70°
- Audio NO
- Dot Pitch 0.077(W) x 0.231(H)mm
- Active Area 110.000(W) x 62.832(H)mm
- Power Input DC 10V-32V
- Operating Temperature -4F to approx. 176F
- Frequency 2400-2483.5 MHz
- Transmission Type Digital Wireless
- Video Input 2 Channel
- Video Source 1vp-p75Ω
- Pairing CH1 Camera Paired
- Power Consumption About 4W
- Transmission Distance 328 ft
- Display Mode Single / Autoscan / Split View
Camera
- Sensor 1/3′ CCD
- Effective Pixel Array 512×492
- Sync. System 700 TV LINES
- Minumination 0.1 LUX
- Working Current 260mA
- Optical Format 1/3 inch
- Camera Correction R-0.45-1.0
- Lens F=3.6 mm
- Viewing Angle 110°
- Waterproof Rating IP69K
- Power Consumption About 3.5W (IR on)
- Power Input DC12 -32V
- Operating Temperature -4F to approx. 176F
- Frequency 2400-2483.5 MHz
- Transmission Type Digital Wireless
- Transmission Distance 328 ft
- S/N Ratio More than 48dB
- White Balance Auto
- IR Control Auto
Wiring The System
CAMERA CONNECTION:
Locate the clearance lights wiring on your vehicle. You may need to remove the
interior panel in order to locate it. Connect the power cables for the camera:
Red wire to the light’s positive; Black wire to chassis ground.
MONITOR CONNECTION:
Cigarette lighter adapter: firmly insert the lighter plug into the cigarette
lighter socket.
DO NOT INSTALL monitor where it may obstruct driver view or obstruct airbag devices.
Position
Monitor Operation
- UP Arrow
- Menu / Selection button
- Down arrow
- Parking Line on/off and Adjust Parking Line Position
- Confirm / CH Selection
Main Menu
Pairing
The system has been paired, connect power and it works. Use pairing unless you
need to add more cameras or replace a camera.
Camera Pairing:
- Un-plug camera’s power connection
- Keep the monitor power connected
- Press monitor button ” Menu”, press ” ” or ” ” scroll to Pairing
- Press “OK”, monitor appears countdown 20 seconds
- Connect the camera to its power source
- Camera signal appears on the monitor
Note: no need to press any button on the camera
FCC Caution
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF warning for Mobile devices:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distan ce 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>