MONOPRICE GM862 Collider 60-60 Mechanical Keyboard Instructions

: June 6, 2024
: Monoprice

Table of Contents

Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bluetooth® Pairing Instructions:
This Bluetooth keyboard can be paired with up to three devices at the same time. The three pairings are saved to Q (default), W, and E. Quickly switch between pairings by holding down the FN key and pressing Q, W, or E. Perform the following steps to pair this keyboard with your device(s).

Set switch on the back of the keyboard to the ON position.
Press and hold the FN and Q + W + E keys for 3-5 seconds. When R starts flashing, the keyboard is ready to connect.
Open the Bluetooth settings on your device and scan for available devices. Locate and select the “Collider 60” entry.
Once the keyboard has connected to your device, the R key will cease flashing, indicating that Bluetooth pairing was successful.

RGB Backlighting and Animations:
FN+I = Static ,Single-on, Single-off. Rotate, Scroll, Roll
FN+O = Fall, Colorful, Glitter, Ripples, Explode, Launch
FN+P = Breath, Outward, Spectrum, Pulsate, Flow, Tilt
FN+>.= Increase backlight brightness
FN+<,= Decrease backlight brightness
FN+[{= Increase backlight speed
FN+]} = Decrease backlight speed
FN+; = Switch dynamic backlight direction
FN+'”= Switch the color of the backlight
Fn + Z/X/C=Backlight Macro recording key

Battery Charging:

Battery Life: Bluetooth – 8 hours. Standby – 3 months.
LED Indicator: Solid Red – Charging, Off – Fully Charged.
FN key will blink repeatedly when the keyboard is low on battery.
After 5 minutes without a keypress, the backlighting will turn off to conserve the battery. After 30 minutes, the keyboard will enter standby mode and disconnect from Bluetooth. Any keypress will reconnect the keyboard.

Custom Backlighting Mode Instructions:

Press FN+Z/X/C (Each key can store a custom backlight mode).
Press FN+Tab – (The LED will flash blue repeatedly to indicate recording).
Press the keys that you wish to set the backlighting for.
Press FN+Tab to exit the custom backlighting mode.

Hot Keys:

FN+WIN: Gaming Mode (Lock Windows® Key)
FN+Backspace: Hold for 3 seconds to reset the Keyboard to factory defaults
FN+Q/W/E: Switch between Bluetooth Profiles
FN+Z/X/C: Swicth between custom backlighting profiles
FN+Tab: Entering/Exiting Custom Backlighting Mode

FCC STATEMENTS:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.