Hooke Road BXG.3020A-1S Mad Max Front Bumper Grill with Wings and Winch Plate User Manual
- June 2, 2024
- HOOKE ROAD
Table of Contents
Hooke Road BXG.3020A-1S Mad Max Front Bumper Grill with Wings and Winch
Plate
Product Specifications
Front Bumper Models: BXG.3020A-1S,
BXG.3020B-S
Contents:
- 1 Front Bumper Assembly
- 8 Hex Bolts
- 2 Button Head Socket Cap Bolts Screws
- 4 Button Head Socket Cap Bolts Screws
- 8 Split Lock Washer
- 2 Split Lock Washer
- 4 Split Lock Washer
- 2 Flat Washer
- 4 Flat Washer
- 8 Flat Washer
- 8 Flange Hex Lock Nuts
- 4 Flange Hex Lock Nuts
- 1 Glue Strip
Tools Required:
- A. 19mm Socket Wrench
- B. 16mm Socket Wrench
- C. 4mm HEX Socket Wrench
- D. 6mm HEX Socket Wrench
- E. 6mm Allen Wrench
Installation Time: About 2 hours, 2-3 people may be needed. Installation time may differ according to your mechanical skill level.
Product Usage Instructions
Step-by-Step Installation Guide:
- Step 1: Begin by removing the original front bumper, and grille, and opening the hood.
- Step 2: Install the Wrench Brackets into the car frame using your original screws.
- Step 3: Install the mounting bracket into the bumper with specified bolts and nuts without tightening them.
- Step 4: Attach the bumper to your vehicle using the provided bolts and nuts.
- Step 5: Glue the glue strip onto the bumper and install it along with the D-rings base into the car frame.
- Step 6: Install the D-rings onto the bumper.
- Step 7: The installation is complete without the wings part.
- Step 8: If you purchased the wings version, follow additional steps to install the wings.
- Step 9: The installation is complete.
- Step 10: Consult your supplier on how to connect the light wire.
Note: Verify all parts are present and carefully read instructions before starting installation.
FAQ
- Q: What should I do if the product parts in the instruction differ from the actual product contents?
- A: Minor differences in parts should generally not affect installation. Contact your distributor for assistance if needed.
- Q: How can I get help with questions about my purchase?
- A: Feel free to contact your distributor for any queries related to your purchase.
Contents
Accessories
If you purchased the wing version, you will receive the following accessories in another package.
Tools required
- A.19mm Socket Wrench;
- B.16mm Socket Wrench;
- C.4mm HEX Socket Wrench;
- D.6mm HEX Socket Wrench;
- E.6mm Allen Wrench;
Installation time
About 2 hours, 2-3 people may be needed. Installationtimemaydifferaccording to
your mechanical skill level. (PLEASE VERIFY ALL PARTS ARE PRESENT AND READ
INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION!)
To view the electronic version (BXG.3020AB-S), please scan the QR code.
Installation Instruction
- Step 1: Begin the installation by removing the original front bumper.And don’t forget to remove the grille and open the Hood.
- Step 2: Install the Wrench Brackets into the car frame using your original screws.
- Step 3: Install the Mountings Bracket into the bumper withtheButtonHeadSocket Cap Bolts Screws (M820), Split Lock Washer (D8), FlatWasher(M820*1), Flange Hex Lock Nuts (M8). Don’t tighten upthosebolts.
- Step 4: Install the Button Head Socket Cap Bolts Screws (M620), SplitLockWasher (D6, Flat Washer (M620*1). Hook up the bumper in your vehicle.
- Step 5: Before installing the bumper, please glue the glue strip into the bumper. Install the bumper & the D-rings base into the car frame withtheHexBolt(M1240), Split Lock Washer (D12), Flat Washer (M122*30), FlangeHexLock Nuts (M12).
- Note : Before installing those bolts, please adjust the positioning of the mounting bracket installed in the previous stepandhangitonyour vehicle.
- Step 6: After all the above, then install the D-ings.The D-rings is very easy to install. As shown below.
- Step 7: The installation is complete (without the wings part). We hope you enjoy a wonderful off-road life with this quality product!
Step 8: If you purchased the wings version, please refer to the below steps to install the wings. Install the wings with the Button HeadSocket CapBoltsScrews (M820 & M616), Split Lock Washer (D8 &D6), Flat Washer(M8161& M6161), Flange Hex Lock Nuts (M8 & M6) .
- Step 9: The installation is complete. We hope you enjoy a wonderful off-road life with this quality product!
- Step 10: How to connect to the light wire. Please ask for your supplier about this explanation.
- Attention:
- 1. The product parts in this instruction may differ slightly from the actual product contents but generally does not affect the installation the product.
- 2. Please feel free to contact your distributor if youhaveanykindof questions
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>