EPOWP THDJ6057LJ Freestanding Bathtub Installation Guide
- June 6, 2024
- EPOWP
Table of Contents
INSTALLATION AND CARE GUIDE
FREESTANDING BATHTUB
Compliance with the following codes & standards:
- 2015 Uniform Plumbing Code® ( UPC )
- 2018 International Plumbing Code® ( IPC )
- 2018 International Residential Code® ( IRC )
- CSA B45.5 / IAPM O Z124-2017- Plastic Plumbing Fixtures
EPOWP
READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT
INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED
BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST
BE OBSERVED FOR SAFE INSTALLATION.
2 PEOPLE ARE REQUIRED TO LIFT AND DURING THE ENTIRE INSTALLATION OF THIS
PRODUCT
This product must be installed by a fully insured and licensed plumber only.
Install on of any our product by anyone other than fully insured and licensed
plumber shall void the limited warranty. We recommend that such licensed
plumber have experience in the installation of products. The limited warranty
is void on any commercial installation We are not responsible for local code
compliance for this product. Building and plumbing codes may vary from state
to state in accordance with your location. We are not responsible for
providing any compliance cerficaons. Under no circumstances we are shall not
be liable for any and all incidental damages sustained in connection with this
product Neither manufacturer, distributor, nor retailer is responsible for
water damage or flood caused due to the use of this product. Under no
circumstances We shall not be liable for any and all fees, cost of installed
on/reinstall on/removal, subsequent damage or transportaon in case of the
product defect
Customer Service Phone: (2 13 )3 75 -2 79 0 . (Monday – Friday 9 AM – 5 PM
Pacific Time)
Or Email: EPOWP@hotmail.com
TOOLS REQUIRED FOR INSTALLATION (NOT INCLUDED)
Inspect the bathtub for any damages. If any damage is found please contact
your retailer.
Carefully, remove the tub from its crate/box.
Important Note: Bathtub must be carried by a minimum of 2 adult people in
an upside-down pose only. Do not carry the bathtub by its panel.
To avoid scratches or damage to the bathtub be sure to set it on cardboard
with so blanket on top of the cardboard.
Set your bathtub on two 4×4 pieces of lumber so you can have access from the
boom of the bathtub. Put a tray beneath the bathtub.
Very Important! Before proceeding with installation, please check that push
pop-up, drain, and integrated overflow are properly sealed and tightened.
Push the pop-up into a close position and fill the bathtub with cold water
above the overflow level to test for overflow leakage and drain leakage.
Check for any leaks around the drain and pipe. (NOTE: Due to surface tension,
it is normal for a small amount of water to pool around the drain)
If leakage occurs please disassemble the drain line or overflow assemblies and
you can apply a plumbing puy/silicone caulk to fix the leakage.
Once the leakage test was performed you may proceed to the installa.
INSTALLATION INSTRUCTIONS
-
Clean, level, and prepare the floor for installa, Place the tub in the exact installed location on the floor and trace the outline of the bathtub with a pencil and mark the drain hole location on the floor. Move the tub away so that the plumbing can be installed.
-
Turn the bathtub upside down and set it on a non-abrasive mat, blanket, or cardboard to prevent any scratches on the tub rim.
-
Place a level across the boom of the tub and adjust the tub feet leveler to touch the level. Then raise the leveler an additional 1/8″ or 3/16″ so that the weight of the tub, water, and user is fully supported by the feet adjuster and not the tub walls.
-
Measure and cut the tailpiece to the appropriate length to reach the trap adapter When se ng the tub drain, insert the tailpiece with 1-1/2″ slip joint and rubber washer into the trap adapter and tighten properly.
-
Apply a generous bead of adhesive or waterproof TJMJDPOF to the boom of the tub and a bead of the tub and le caulk around the edge of the tub
-
Flip the tub over and carefully set the tub into posi on with tailpiece assembly to 1USBQ and connect to the drain.
-
Fill the tub with water to the overflow and then drain the tub while inspec ng the waste and overflow connect on below the floor for any leaks. Access from below will be necessary for this step.
-
With the tub now set in place, wipe off any excess tub or le caulking, adhesive where the tub meets the floor with a wet cloth.
-
DO NOT SHOWER or MOVE the tub and er installa it on because it will take about 24 hours to get the silicone sealant to dry.
IMPORTANT SAFETY RULES
ATTENTION! ALWAYS FOLLOW THESE PRECAUTIONS WHEN USING A BATHTUB
Warning The bathtub must be installed and used as described in this
manual
Warning Use caution when entering or exiting the bathtub
Warning Do not permit children or persons with infirmities to use the
bathtub without the supervision of an adult
Warning People using any medications or having adverse medical history
must consult a physician prior to use of the bathtub to avoid potent al
hyperthermia and possible drowning
Warning Water temperature over 100ºF may cause hyperthermia and/or other
health problems. Check water temperature and adjust it for your personal
comfort
Warning Never uses bathtub while intoxicated, er taking meals, or any
alcoholic beverages. Consuming alcoholic beverages before or during bathing
will cause drowsiness and may result in hyperthermia, loss of consciousness,
or even drowning
Warning If you are pregnant or you feel that you are maybe pregnant,
consult your doctor before using the bathtub
Warning Never use any electrical devices such as hairdryer, lamp,
telephone, tv, radio, or others within 5 feet of the bathtub
Warning Do not overfill the bathtub before entering. Entering the bathtub
when filled will cause overflow and slippery conditions. Use extreme care on
when entering and exing
Care and Cleaning
- Most dirt will wash off with mild soap and warm water.
- For tough spots, use liquid dishwashing soap or non-chlorine bleach.
- Do not use abrasive material such as steel wool or scouring pads to clean the acrylic surface.
- Always test the cleaning solution in a small area before using it on the en resurface.
- Do not allow cleaning to soak on the acrylic surface.
- Rinse thoroughly with water immediately and wipe dry with so cloth.
Repair and Maintenance
- Use liquid polish compounds such as Gel-Gloss Kitchen and Bath Polish(TM) to keep the original shine of the acrylic surface.
- Light scratches can be removed with polishing compounds for automobiles.
- For deeper scratches use wet sandpaper (1500 grit or higher).
- Always add water when sanding and lightly sand the area larger than the scratch in a circular moon to remove the scratches. Repeat un l the scratch is removed. Use so cloth and a small amount of polishing compound to restore shine. Repeat as needed un l surface shine is restored.
IMPORTANT!
DO NOT USE abrasive cleaners such as acid, ammonia, bleach, and similar
solutions. The use of such solutions may cause corrosion, finish peeling,
and/or dull the surface. DO NOT USE abrasive sponges or cloth. Never use
steel, wool, or wire brushes that will permanently scratch the surface.
Retain this installa on instruc one for future reference!
Please don’t hesitate to contact us if you have any questions or concerns.
Customer Service Phone: 2 13 -3 75 -2 79 0 .
(Monday – Friday 9 AM – 5 PM Pacific
Time) Or Email: EPOWP@hotmail.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>