MINKA LAVERY 6203-44 Vantage 1-Light Brushed Nickel Metal Shade Pendant Instruction Manual

MINKA LAVERY 6203-44 Vantage 1-Light Brushed Nickel Metal Shade Pendant

Product Information

• Product Name: Item#6203-44/66A/84
• Date of Manufacture: January 5, 2023
• Product Type: Fixture

Product Usage Instructions

1. Before starting the installation, make sure to shut off the power at the fuse box or circuit breaker box.
2. Mounting the Fixture:
   • Refer to Fig.1 for the visual representation of the mounting process.
   • Securely mount the fixture by following the instructions provided in the user manual.
3. Connecting the Wires:
   • Refer to Fig.2 for the visual representation of the wire connections.
   • Connect the electrical wires as shown in Fig.2.
   • Ensure that all wire connectors (A) are secured.
   • If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
   • If there is no ground wire in your outlet box, connect the fixture’s ground wire directly to the mounting plate (B) using the provided green screw.
   • Tuck wire connections neatly into the outlet box.
4. Finishing the Installation:
   • Refer to Fig.1 for the visual representation of the finishing steps.
   • Place the canopy (E) over the mounting plate (B) and secure it with screws (D).
   • Install one medium base (E26) bulb (G) up to 60 watts each or CFL or LED equivalent (bulb not included) according to the fixture specification.
   • Ensure that you do not exceed the maximum wattage rating.
5. After completing the installation, restore power and test the fixture to ensure proper functionality.

Note: The illustration in Fig.1 is for installation purposes only and may or may not be identical to the purchased fixture.

IMPORTANT
It is recommended to have the fixture installed by a qualified electrician to ensure proper wiring and installation.

MOUNTING THE FIXTURE (Fig.1)

1. Shut off power at the fuse box or circuit breaker box and remove the old fixture, including the mounting hardware.

2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.

3. Attach the mounting plate (B) to outlet box (not included) using outlet box screws (C) (SIZE: #8-32N, L0.5″). The side of the mounting plate (B) marked “GND” must face out.

4. Adjust the wire to desired hanging length using the small screw located on the side of the wire grip (F) with a flathead screwdriver (not included). Ensure to re-tighten the set screw after wire adjustment. To straighten the cord, please use a blow dryer (not included) if necessary.

5. Remove any excess wire leaving approximately 7″ beyond canopy (E) for wire connections.
   CONNECTING THE WIRES (Fig.2)

6. Connect the electrical wires as shown in Fig.2, making sure that all wire connectors (A) are secured. If your outlet box has a ground wire (green or bare copper), connect the fixture’s ground wire to it.
   Otherwise, connect the fixture’s ground wire directly to the mounting plate (B) using the green screw provided.

7. Tuck wire connections neatly into the outlet box.
   FINISHING THE INSTALLATION (Fig.1)

8. Place canopy (E) over the mounting plate (B) and secure with screws (D).

9. Install (1) one medium base (E26) bulb (G) up to 60 watts each or CFL or LED equivalent (not included) in accordance with the fixture specification—DO NOT EXCEED THE MAXIMUM WATTAGE
   RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). Your installation is now complete. Return power and test the fixture.

Note: The illustration (Fig.1) in this manual is for installation purposes only. It may or may not be identical to the fixture purchased.

IMPORTANT
FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>