PERLEGEAR PGLF12-U Full Movement TV Wall Mount Instruction Manual

PERLEGEAR PGLF12-U Full Movement TV Wall Mount

Dimension

IMPORTANT SAFETY INFORMATION

NOTE

• Please carefully read all instructions before attempting installation. If you DO NOT understand the instructions or if you have any questions or concerns, please call technical support or email customer service.
• Before starting assembly, verify that all parts are included and undamaged. DO NOT use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
• NOT all hardware included in this package will be used.

CAUTION

• Avoid the risk of personal injury or property damage!
• DO NOT use this product for any purpose that is NOT explicitly specified in this manual. DO NOT exceed the maximum weight capacity.
• We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.

WARNING

• This product is designed for use on wood studs, solid concrete, and brick walls. DO NOT install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.

Note for Wood Stud Installation

• Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). DO NOT use a drill; only use a socket wrench.
• DO NOT use wall anchors for this mounting option. Wall anchors are used for solid concrete and brick wall installations only.
• Minimum wood stud size: 1 1/2″ W x 3 1/2″ D (38 x 89mm)
• Wood stud spacing: 12″ (305mm) to 16″ (406mm) (center to center)
• note: If the wood studs are more than 16″ (406mm) apart, or if the studs are NOT in the desired mounting location, you can secure (2) wood boards (or extension brackets) to the wall studs, then install the TV mount on the boards. Minimum wood board dimensions: 1 1/2″ T x 3 1/2″ W x >18″ L (38 × 89 x >457mm)

Note for Solid Concrete and Brick Wall Installation

• Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). DO NOT use a drill; only use a socket wrench.
• Mount the arm assembly/wall plate directly on the concrete surface.
• Minimum solid concrete thickness: 8″ (203mm)
• Never drill into the mortar between bricks.

INSTALLATION INSTRUCTION

Before getting started, make sure this mount is compatible.

• VESA Pattern Compatibility 200 × 100mm 400 x 200mm
• If the TV weighs more than 132 Ibs (60kg), DO NOT use this product.
• Suitable for installation on wood studs, solid concrete, and brick walls. DO NOT install on drywall

Tools Needed

(Not Included)

• For Wood Stud Walls
• For Solid Concrete or Brick Walls

Contents

Step 1 Attach TV Brackets to TV

• Select TV Bolts
• Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6, or M8) to use. A minimum of 4-5 turns into the threading is required. DO NOT turn past the bottom of the hole.
• Spacer and Bolt Configurations
• Flat Back TV (See Option A)
• Curved TV (See Option B)
  • Bump (See Option C)
• Cables (See Option D)
  • Recessed Holes (See Option E)

Attach the TV Brackets to Your TV

Option A

• Option A: For Flat Back TVs
  • Add spacers if needed to fit the bolt length and TV back.

Option B

• Option B: For Curved Back TVs
  • Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

Option C

• Option C: For TVs with a Bump
  • The TV brackets must be flush on the bump and leveled by spacers on the gap.

Option D

• Option D: For TVs with Protruding Cables
  • Use spacers to create extra space between the TV and TV brackets

Option E

• Option E: For TVs with Recessed Holes
  • Spacers need to fill in the recessed holes on the back of the TV while keeping the TV brackets as close to the TV as possible.

Step 2 Mount the Arm Assembly / Wall Plate on the Wall

• Use a stud finder to locate wood studs, or use an awl to find the edges. Mark the edge and center positions.
• Position the wall plate template [02] at your desired height and line up the holes with your stud centerline. Level the wall plate template L02 and mark the holes.
• Drill 4 pilot holes using a 7/32″ (5.5mm) diameter drill bit. Make sure the depth is not less than 2 3/4″ (70mm).
• Mount the arm assembly/wall plate [04] on the wall using the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (DO NOT overtighten).
• Position the wall plate template [02] at your desired height. Level the wall plate template [02] and mark the holes. Drill 4 pilot holes using a 3/8″ (10mm) diameter drill bit.
• Make sure the depth is not less than 3″ (75mm). Never drill into the mortar between bricks.
• Use a hammer to tap the anchors [A2] into the drilled holes. Ensure the anchors [A2] are seated flush with the concrete or brick surface.
• Mount the arm assembly/wall plate [04] on the wall using the lag screws [A1] and anchors [A2]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (DO NOT overtighten).

Step 3 Verify that the Mount is Firmly Mounted

Step 4 Attach the Front Support to the Arm Assembly / Wall Plate

• Insert the front support bars [05] and [06] into the arm assembly/wall plate [04], then tighten bolts [G1] to secure them.
• Attach the end caps [07] to the front support using bolts [G2]

Step 5 Attach the EVA Pads to the Wall Plate (If Needed)

Step 6 Hang the TV on the Front Support Assembly

• Hang the TV on the front support using the hooks on the brackets.
• Make sure the upper and lower hooks on the TV brackets fit over the front support bars.
• Then flip the safety locks up and fasten them using bolts [G3].

Step 7 Tilt Adjustment

CAUTION: DO NOT overtighten or over-loosen the lever.

• Slightly loosen the lever [T1]. Adjust the TV to your desired tilt angle. Retighten the lever [T1] to lock the tilt angle.
• TIP: If the tilt angle can’t be locked, tighten the nut [2].

Step 8 Level Adjustment

• CAUTION: DO NOT overtighten or over-loosen the nuts.
• If needed, the TV can be leveled. Slightly loosen the 4 leveling nuts IL]. Level your TV.
• Retighten the leveling nuts [L] to hold the TV in position.

Frequently Asked Questions

1. Question How should I manage the cables?
   • Use the cable ties.
2. Question What should I do if my stud spacing is greater than 16″ or if I can’t center the mount on the wood studs?
   • Hardwood Boards
   • Board Size: 1 1/2″ T x 3 1/2″ W (38 x 89mm). The wood boards and studs must be capable of supporting four times the weight of the TV and TV wall mount combined.
   • Buy two hardwood boards long enough to cover the gap between two wood studs and firmly attach them.
   • Self-supplied lag screws: 1/2 x 4″. Screw in at least 1″ from the ends of the boards.
   • Securely attach the TV Wall Mount to the boards.
3. Question How do I find the right height for mounting the TV?
   • The simplest method is to position the TV so that the center is the same height as your eye level while viewing. Scan the QR code to watch the mounting video, which covers this in more detail.
4. Question Is it too hard to adjust the swivel angle or extension of the TV Wall Mount?
5. Mount the TV and Wall Mount on the wall before trying to move the arms. Only move the TV by the left and right edges. DO NOT push on the screen of the TV.
6. If you have tried Option 1 but adjustment is still too hard, try lubricating the arm joints with a few drops of machine oil.
7. Question How can I raise/lower the TV if the TV Wall Mount is already fixed on the wall?
8. • Answer:
9. Remove the TV from the TV Wall Mount.
10. Remove the TV brackets from the TV and reattach them according to instructions A or B in the picture below (A for lifting the TV or B for lowering the TV).
11. Hang the TV on the TV Wall Mount and secure it.

• A. To raise the TV by a few inches, reattach the TV brackets using the upper holes in the brackets.
• B. To lower the TV by a few inches, reattach the TV brackets using the lower holes in the brackets.
• 1-800-456-5231 (US/CA)
• 44-808-196-4165 (UK)
• support@perlegear.com
• www.perlegear.com
• EC REP AMZLAB GmbH
• Laubenhof 23,45326 Essen
• info@amz-lab.de
• THEMIS AR support Itd.
• UK REP 85 Great Portland St, London, United Kingdom.
• info@amz-lab.de
• Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED
• Address: FLAT/RM 185 G/F HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>