PERLEGEAR PGLF12 Full Motion TV Wall Mount Instruction Manual

PERLEGEAR PGLF12 Full Motion TV Wall Mount

PERLEGEAR
FULL-MOTION TV WALL MOUNT
INSTRUCTION MANUAL RevO1 (A)
MODEL
PGLF12

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the industry. If you have any installation questions or issues with the product, please contact us at the number below.

OVERVIEW

1. TV Bracket
2. Front Support Bar
3. Front Support Bar
4. End Cap
5. Arm Assembly/ Wall Plate
6. G1 Bolt
7. G2 Bolt
8. G3 Foam Pad

BEFORE GETTING STARTED, LET’S MAKE SURE THIS MOUNT IS PERFECT FOR YOU

1 Check VESA Pattern Com patibility|

Measurement Conversion

100mm = 3.9″                400mm = 15.7″

200mm = 7.9″               500mm = 19.7″

300mm = 11.8″             600mm = 23.6″

Minimum:

200mm / 7.9″ [Wl x 100mm / 3.9″ [Hl

Maximum:

600mm / 23.6″ [Wl x 400mm / 15.7″ [Hl

If this mount is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.co

---|---
2 Check Max Load|

If your TV weighs more,this mount is NOT compatible.

WARNING

DO NOT exceed the Max load indicated. Use with products heavier than the Max load may result in failure of the mount, which could cause damage or injury.

3

Check Wall Type

| A CAUTION:

DO NOT install in drywall aloneI

If you’re not sure of the wall type, or for guidance on other wall structures, please contact our Technical Support line as listed above or Customer Service at support@perlegear.co

4

Important Safety Information

| Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any concerns or questions, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

CAUTION: Avoid the risk of personal injury or property damageI

• Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the Max load. We’re not liable for damage or injury caused by incorrect assembly, improper mount­ ing, or inappropriate use. Do not use outdoors.

• This product is designed for use in wood stud, solid concrete, concrete block, and brick walls. DO NOT install in drywall alone.

• The wall must be capable of supporting four times the weight of the TV and mount combined.

• Route cords and cables properly to avoid mechanical damage.

SAVE THESE INSTRUCTIONS.

TOOLS NEEDED [NOT INCLUDED)

For Mounting on Wood Stud Walls

For Mounting on Solid Concrete, Concrete Block, or Brick Walls

A NOTE ON SUPPLIED PARTS AND HARDWARE

WARNING: This product contains small parts that may pose a choking hazard.
Before starting assembly, check all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

NOTE: Not all hardware included in this package will be used.

SUPPLIED PARTS AND HARDWARE

CAUTION!
This anchor is for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs.

NOTE: The washers, spacers, and bolts shown above are displayed in accordance with actual size.

INSTALLATION

STEP 1 ATTACHING THE TV BRACKETS TO YOUR TV
Before attaching the TV brackets to your TV, remove the preassembled bolts [S] and keep them for Step 6.

SELECT TV BOLTS
Only one bolt size fits your TV.

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or MB] to use. We recommend screwing in at least five turns. Do not turn past the bottom of the hole.

SPACER AND BOLT CONFIGURATIONS

ATTACH THE TV BRACKETS TO YOUR TV

CAUTION
The round holes should be directed toward the top and the slotted holes toward the bottom.
The brackets should be equally centered from the top and bottom of the TV and must be fastened securely in place.

OPTION A: FOR FLAT BACK TVS
Add spacers, if needed, to fit the bolt length and TV back.

OPTION B: FOR CURVED BACK TVS
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

OPTION C: FOR TVS WITH A BUMP
The TV brackets must be flush on the bump and leveled by spacers on the gap.

OPTION D: FOR TVS WITH PROTRUDING CABLES
Use spacers to create extra space between the TV and TV brackets.

OPTION E: FOR TVS WITH RECESSED HOLES
Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.

STEP2 MOUNTING THE ARM ASSEMBLY/ WALL PLATE ON THE WALL
For mounting on wood stud walls, go to Option A.
For mounting on solid concrete, concrete block, or brick walls, go to Option B.

OPTION A: MOUNTING ON WOOD STUD WALLS

IMPORTANT: Maximum horizontal distance between fasteners is 16″ [406mm).

• Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [DO NOT overtighten]. Do not use a drill; only use a socket wrench.
• Do not use wall anchors [A2] for this mounting option. Wall anchors [A2] are used for solid concrete, concrete block, and brick installations only.
• Any material covering the wall must not exceed 5/8″ [16mm].
• Minimum wood stud size: 1 1/2″ W x 3 1/2″ D [38 x 89mm].
• Wood stud spacing: 12″ to 16″ [center to center].

NOTE: If the wood studs are more than 16″ apart, or if the studs are not in the desired mounting location, you can secure [2] wood boards or extension brackets to the wall studs, then install the TV mount on the boards. Minimum wood board dimensions: 1 1/2″ T x 3 1/2″ W x > 18″ L [38 x 89 x >457mml. Go to page 20 for details.

1. Use a stud finder [not included] to locate wood studs, or use an awl [not included] to check the edges. Mark the edge and center positions.

2. Position the wall plate template [06] at your desired height and line up the holes with your stud centerline. Level the wall plate template and mark the holes.

3. Drill four pilot holes using a 7/32″
   [5.5mm] diameter drill bit. Make sure the depth is not less than 2 3/4″
   [70mm].

4. Mount the arm assembly/ wall plate [05] on the wall using the lag screws [A 1l. Tighten the lag screws only until they are pulled firmly against the wall plate [DO NOT overtighten].

OPTION B: MOUNTING ON SOLID CONCRETE, CONCRETE BLOCK, OR BRICK WALLS

WARNING

• Avoid the risk of personal injury or property damage! Tighten the lag screws [A 1l only until they are pulled firmly against the wall plate [DO NOT overtighten]. Do not use a drill; only use a socket wrench. Use wall anchors [A2] for this mount­ing option.
• Mount the arm assembly/ wall plate [05] directly on the concrete surface.
• Minimum solid concrete thickness: 8″ [203mm].
• Minimum concrete block size: 8″ x 8″ x 16″ [203 x 203 x 406mm].
• Never drill into the mortar between blocks or bricks.

1. Position the wall plate template [06] at your desired height. Level the wall plate template and mark the holes.

2. Drill four pilot holes using a 3/8″
   [10mm] diameter drill bit. Make sure the depth is not less than 3″ [75mm]. Never drill into the mortar between blocks or bricks.

3. Use a hammer to knock the anchors [A2] into the drilled holes. Ensure the anchors are seated flush with the concrete or brick surface.

4. Mount the arm assembly/ wall plate [05] on the wall using the lag screws
   [A 1] and anchors. Tighten the lag screws only until they are pulled firmly against the wall plate [DO NOT overtighten].m

STEP3 TESTING TV WALL MOUNT INSTALLATION
Before hanging the TV on the mount, pull down on the mount with your hands to check that it’s securely installed.

STEP4 ASSEMBLING THE FRONT SUPPORT

1. Insert the front support bars [02] and [03] into the arm assembly/ wall plate [05]. then tighten bolts [G1] to secure them.
   NOTE: The position of the screw holes on support bars in this step.

2. Attach the end caps [04] to the front support using bolts [G2].

STEP 5 ATTACHING THE FOAM PADS [G3] TO THE ARMS (OPTIONAL)

STEP6 MOUNTING THE TV ON THE FRONT SUPPORT ASSEMBLY
Hang the TV on the arm assembly/ wall plate [05] using the hooks on both brackets. Then flip the safety locks up and fasten using bolts [S].

STEP 7 ADJUSTING THE TILT ANGLE OF THE TV

CAUTION: DO NOT overtighten or overloosen the lever.

Turn the lever handle 90 degrees, then slightly loosen the lever [Tl. Adjust the TV to your desired tilt angle. Retighten the lever [Tl to lock the tilt angle.

STEP 8 LEVELING THE TV

CAUTION: DO NOT overtighten or overloosen the nuts.

Directly level your TV. If it is difficult to level your TV, slightly loosen 4 leveling nuts [L], and level your TV. Retighten the leveling nuts [L] to hold TV in place.

FREQUENTLY ASKED QUESTIONS

QUESTION 1
What should I do if my stud spacing is greater than 16″ or if I can’t center the mount on the wood studs?

OPTION A: HARDWOOD BOARDS

1. Buy two hardwood boards long enough to cover the gap between two wood studs and firmly attach them.
   • Board Size: 1 1/2″ T x 3 1/2″ W [38 x 89mm].
   • The wood boards and studs must be capable of supporting four times the weight of the TV and TV wall mount combined.
2. Securely attach the TV Wall Mount to the boards.

OPTION 8: EXTENSION BRACKET

1. Attach extension brackets to the TV Wall Mount.
   If you have any questions about obtaining extension brackets, please contact customer service for more information.

2. Install the TV Wall Mount on the wood studs using the extension brackets.

1-800-456-5231 (US/CA)
44-808-196-4165 (UK)
support@perlegear.com

QUESTION 2 How do I find the right height for mounting the TV?

The simplest method is to position the TV so that the center is the same height as your eye level while viewing. Scan the QR code to watch the mounting video, which covers this in more detail.

QUESTION 3
How can I raise/lower the TV if the TV Wall Mount is already fixed on the wall?

1. Remove the TV from the TV Wall Mount.
2. Remove the TV brackets from the TV and reattach according to instructions A or Bin the picture below [A for lifting up the TV or B for lowering the TV].
3. Hang the TV on the TV Wall Mount and secure.
   • A. To raise the TV by a few inches,reattach the TV brackets using the upper holes in the brackets.
   • B. To lower the TV by a few inches, reattach the TV brackets using the lower holes in the brackets.

QUESTION 4
It’s too hard to adjust the swivel angle or extension of the TV Wall Mount.

1. Mount the TV and Wall Mount on the wall before trying to move the arms. Only move the TV by the left and right edges. Do not push on the screen of the TV.
2. If you have tried Option 1 but adjustment is still too hard, try lubricating the arm joints with a few drops of machine oil.

THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT

[US/CA) 1-800-456-5231
[UK) 44-808-196-4165
Mon-Fri, 8am-8pm [CST)
Mon-Fri, 2pm-1 0pm [UTC)

support@perlegear.com 
www.perlegear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>