PERLEGEAR PGMT7 Studless TV Wall Mount Instruction Manual

June 14, 2024
Perlegear

PERLEGEAR PGMT7 Studless TV Wall Mount

PERLEGEAR PGMT7 Studless TV Wall Mount-p0roduct

Instruction

FIXED TV WALL MOUNT INSTRUCTION MANUAL

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the industry. If you have any installation questions or issues with the product, please contact us at the number below.

ASSEMBLY VIDEO

PERLEGEAR PGMT7 Studless TV Wall Mount 02

PERLEGEAR PGMT7 Studless TV Wall Mount 03

  1. TV Bracket
  2. Wal[ Plate
  3. Bumper

BEFORE GETTING STARTED, LET’S MAKE SURE THIS MOUNT IS PERFECT FOR YOU

Check VESA Pattern Com patibility|

  • Measurement Conversion
  • Max 100mm = 3.9″               300mm  = 11.8″
  • 4 1 0 5 0 . m 7″ m **** 200mm  = 7.9″               400mm  = 15 .7″
  • Max: 1 5 . 7″
  • Minimum: 1 **40 ****: m ** 100 x 100mm [3 . 9″ x 3.9″
  • Maximum 400 x 400mm [15.7″ x 15.7″)

If this mount is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com .

---|---
Check Max Load| W ARNING
DO NOT exceed the Max load indicated . Use with products heavier than the Max load may result in If your TV weighs more, failure of the mount, which could


this mount is NOT compatible. cause damage or injury.

Check Wall Type| Wood Studs     Drywall Only    Solid Concrete or (with drywall)     Brick Walls

PERLEGEAR PGMT7 Studless TV Wall Mount 06

If you’re not sure of the wall type, or for guidance on other wall structures, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com .

Important Safety Information| Please carefully read all instructions before attempting installati on . If you do not understand the instructions or if you have any concerns or questions, please contact our Technical Support line as listed above or

Customer Service at support@perlegear.com .

A CAUTION Avoid the risk of personal injury or property damage!

  • Do not use this product for any purpose that is NOT explicitly  specified  in this manual. Do not exceed  the Max load . We’re not liable for damage or injury caused by incorrect assembly, improper mounting, or inappro­priate use. Do not use outdoors .
  • This product is designed for use in wood studs, drywall, solid concrete, and brick walls.
  • The wall must be capable of supporting four times the weight of the TV and mount combined .
  • Route cords and cables properly to avoid mechanical damage .

SAVE THESE INSTRUCTIONS.

TOOLS NEEDED (NOT INCLUDED)

PERLEGEAR PGMT7 Studless TV Wall Mount 07

| Phillips Screwdriver|

7/16″ [11mm)

Socket Wrench

For Mounting on Wood Stud Walls

OR 5/32″ [4mm) Stud Finder Awl  Wood Drill Bi

| For Mounting on Drywall

Hammer

| For Mounting on Solid Concrete or Brick Walls

3/8″ [10mm) Concrete Drill Bit     Hammer

A NOTE ON SUPPLIED PARTS AND HARDWARE
WARNING: This product contains small parts that may pose a choking hazard .

Before starting assembly, check all parts are included and undamaged. Do not use damaged or defective parts . lf you require replacement parts, contact our Technical Support line as listed above or Customer Service at support@perlegear.com .

NOTE: Not all hardware included in this package will be used.

SUPPLIED PARTS AND HARDWARE
| 01 X 2 TV Bracket| PERLEGEAR PGMT7 Studless TV Wall Mount
011| | CJ 02 X 2 Bumper
Washer| | | Spacer b xB L2.5mm

| |
| 0| | IL “‘O””
x 4| x 4| x 4| x 4
M4/M5| M6/M8| L10mm| L22mm

TV Bolt

CAUTION
DO NOT use these nails on concrete or brick walls.

PERLEGEAR PGMT7 Studless TV Wall Mount 018

AUTION

  • This anchor is for concrete or brick walls ONLY.
  • DO NOT use them on drywall or wood studs.

NOTE
The washers, spacers, bolts, and screws shown above are displayed in accordance with actual size.

TIP

We offer different bolts and spacers to fit different TVs, but only one bolt size fits your TV. Take it easy for it might take a few attempts to find the perfect fit.
BOLT DIAMETER
Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt diameter [M4, M6 or M8] to use.|}
PERLEGEAR PGMT7 Studless TV Wall Mount 020

AUTION
Verify adequate thread engagement with your bolt/washer/spacer combination AND the TV bracket. [STEP 1.2].
PERLEGEAR PGMT7 Studless TV Wall Mount 022

  • TOO LONG will damage the TV.
  • TOO SHORT will not hold the TV.

BOLT LENGTH] AND SPACER COMBINATION

  • No spacers are needed

  • Spacers are needed

If you have the TV as the following situation, you need to use longer bolts and spacers combination.

PERLEGEAR PGMT7 Studless TV Wall Mount 027

ACAUTION
Make sure the TV brackets are flush with the leveling feet.

ATTACH THE TV BRACKETS AND BUMPERS TO YOUR TV

PERLEGEAR PGMT7 Studless TV Wall Mount 029

For the two mounting holes at the top.

BOLT/SPACER/WASHER COMBINATION OPTIONS (ONLY FOR REFERENCE)

  • No spacers are needed
    PERLEGEAR PGMT7 Studless TV Wall Mount 030

  • Spacers are needed

For the two mount­ing holes at the bottom.

PERLEGEAR PGMT7 Studless TV Wall Mount 031

STEP2 MOUNTING THE WALL PLATE ON THE WALL

WARNING
Avoid the risk of personal injury or property damage!

OPTION A: MOUNTING ON WOOD STUD WALLS (PAGE 09-10)

  • Applicable Wood Stud Spacing: 8″, 12″ or 16″ [center to center]. If your wood studs are not 8″, 12″ or 16″ [406mm] apart OR you can not center wall plate on your studs, follow STEP 2B on PAGE 11, for drywall installation.
  • Minimum wood stud size: 1 1/2″ W x 3 1/2″ D [38 x 89mm]
  • Any material covering the wall must not exceed 5/8″ [16mm].
  • Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [DO NOT overtightenl. Do not use a drill; only use a socket wrench.

NOTE: DO NOT use wall anchors [A2] for this mounting option. Wall anchors [A2] are used for solid concrete and brick installations only.

  • Use a stud finder to locate wood studs, or use an awl to check the edges. Mark the edge and cent

  • The center of both studs must be located for proper installa­tion.

  • Position the wall plate template [04] at your desired height and line up the holes with your stud centerline. Level the wall plate template and mark the holes.

  • Drill 2 pilot holes in the center of the studs using a 5/32″ [4mm] diameter drill bit. Make sure the depth is not less than 2 3/4″ [70mm].

  • Mount the wall plate [03] on the wall using the lag screws [A 1l. Tighten the lag screws [A 1l only until they are pulled firmly against the wall plate [DO NOT overtightenl.

WARNING

  • Avoid the risk of personal injury or property damage!
  • Do not install on plaster & lath walls.

OPTION B: MOUNTING ON DRYWALL ONLY (PAGE 11)

  • It is an installation option if the TV wall mount can not be centered over two wood studs.
  • Drywall covering must exceed 3/8″ [9.5mm].
  • Drywall must be of sound construction with no water damage. If water damage occurs, remove the TV immediately.
  • If any of the nails encounter excessive resistance [metal objects). please stop and contact us.
  • Do not mount to patched areas, drywall seams, or uneven walls.
  • Do not reuse the nails after removal. Do not use store-bought nails.

NOTE : Do not use wall anchors or lag screws for this mounting option.

Position the wall plate [03] at your desired height. Mount the wall plate on the wall using the nails [G]. Tap a nail into one of the outer holes, then level the wall plate and tap a nail into a hole on the other side.

CAUTION

  • Install the nails at a downward angle, not straight into the wall.

  • Tap the remaining 18 nails [G] from one side to the other.

WARNING
Avoid the risk of personal injury or property damage!

OPTION C: MOUNTING ON SOLID CONCRETE OR BRICK WALLS (PAGE 12-13)

  • Tighten the lag screws [A 1] only until they are pulled firmly against the wall plate [DO NOT overtightenl. Do not use a drill; only use a socket wrench.
  • Mount the wall plate directly on the concrete surface.
  • Minimum solid concrete thickness: 8″ [203mm]
  • Never drill into the mortar between bricks.

NOTE : Use wall anchors [A2] for this mounting option.

  • Position the wall plate template [04] at your desired height. Level the wall plate template and mark the holes.

  • Drill 2 pilot holes using a 3/8″ [10mm] diameter drill bit. Make sure the depth is not less than 3″ [75mm). Never drill into the mortar between bricks.

PERLEGEAR PGMT7 Studless TV Wall Mount 048

  • Use a hammer to tap the anchors [A2] into the drilled holes. Ensure the anchors are seated flush with the concrete or brick surface.

  • Mount the wall plate [03] on the wall using the lag screws [A 1] and anchors [A2]. Tighten the lag screws [A 1] only until they are pulled firmly against the wall plate [DO NOT overtightenl.

STEPJ TESTING TV WALL MOUNT INSTALLATION

Before hanging the TV on the mount, pull down on the mount with your hands to check that it’s securely installed.

PERLEGEAR PGMT7 Studless TV Wall Mount 054

MOUNTNG THE TV ON THE WALL PLATE

If latches are open, press down on the latches. Make sure to close the latches. Hang the TV on the wall plate [03]. then press forward. The latches should engage on the wall plate [03].

AUTION
Make sure the safety latches are in the locked position so the TV is securely fastened to the wall plate.

PERLEGEAR PGMT7 Studless TV Wall Mount 055

REMOVING THE TV

To remove the TV, first disconnect all cables. Pull the cords [R] down and hold them while gently pulling the bottom of the TV away from the wall plate [03]. Exerting too much force may cause the latches to break. Once the latches are free, lift the TV up and off of the wall plate [03].

THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT

support@perlegear.com
www.perlegear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals