PERLEGEAR PGLF18-Manual-XS Corner TV Wall Mount Long Arm TV Mount Bracket Instruction Manual

PERLEGEAR PGLF18-Manual-XS Corner TV Wall Mount Long Arm TV Mount Bracket

PRODUCT OVERVIEW

• 01 TV Bracket
• 02 Front Support Bar
• 03 Front Support Bar
• 04 End Cap
• 05 Arm Assembly/ Wall Plate
• G1 Bolt
• G2 Bolt
• G3 Bolt

BEFORE GETTING STARTED, LET”S MAKE SURE THIS MOUNT IS PERFECT FOR YOU

1. Check VESA Pattern Compatibility

2. Measurement Conversion

3. 100mm = 3.9″

4. 200mm = 7.9″

5. 300mm = 11.8″

6. 400mm = 15.7″

7. 500mm = 19.7″

8. 600mm = 23.6″

9. Minimum:
   200 x 100mm [7.9 x 3.9″)

10. Maximum:
    600 x 400mm [23.6 x 15.7″)
    If this mount is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

11. Check Max Load
    WARNING
    DO NOT exceed the Max load indicated. Use with products heavier than the Max load may result in failure of the mount, which could cause damage or injury.
    If your TV weighs more, this mount is NOT compatible.

12. Check Wall Type
    CAUTION:
    DO NOT install in drywall alone!
    If you’re not sure of the wall type, or for guidance on other wall structures, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

4. Important Safety Information
   Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any concerns or questions, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.
   CAUTION: Avoid the risk of personal injury or property damage!

   • Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum weight capacity. We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use. Do not use outdoors.
   • This product is designed for use in wood stud, solid concrete and brick walls. DO NOT install in drywall alone.
   • The wall must be capable of supporting four times the weight of the TV and mount combined.
   • Route cords and cables properly to avoid mechanical damage.
     SAVE THESE INSTRUCTIONS.

TOOLS NEEDED [NOT INCLUDED)

For Mounting on Wood Stud Walls

For Mounting on Solid Concrete or Brick Walls

A NOTE ON SUPPLIED PARTS AND HARDWARE

WARNING: This product contains small parts that may pose a choking hazard.
Before starting assembly, check all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Technical Support line as listed above or Customer Service at support@perlegear.com.
NOTE: Not all hardware included in this package will be used.

SUPPLIED PARTS AND HARDWARE

INSTALL ATION

• STEP 1 ATTACHING THE TV BRACKETS TO YOUR TV
  • SELECT TV BOLTS
    Only one bolt size fits your TV.
    Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or M8) to use. We recommend screwing in at least five turns. Do not turn past the bottom of the hole.

  *  **SPACER AND BOLT CONFIGURATIONS

**

  *  **ATTACH THE TV BRACKETS TO YOUR TV**  

CAUTION: The round holes should be directed toward the top and the slotted holes toward the bottom.
The brackets should be equally centered from the top and bottom of the TV and must be fastened securely in place.

  *  **OPTION A: FOR FLAT BACK TVS**  

Add spacers if needed to fit the bolt length and TV back.

  *  **OPTION B: FOR CURVED BACK TVS**  

Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

  *  **OPTION C: FOR TVS WITH A BUMP**  

The TV brackets must be flush on the bump and leveled by spacers on the gap.

  *  **OPTION D: FOR TVS WITH PROTRUDING CABLES**  

Use spacers to create extra space between the TV and TV brackets.

  *  **OPTION E: FOR TVS WITH RECESSED HOLES**  

Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.

• STEP2 MOUNTING THE ARM ASSEMBLY/ WALL PLATE ON THE WALL
  For mounting on wood stud walls, go to Option A. For mounting on solid concrete or brick walls, go to Option B.

  • OPTION A: MOUNTING ON WOOD STUD WALLS
    Avoid the risk of personal injury or property damage! Tighten the lag screws [A 1] only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a socket wrench.
    Do not use wall anchors [A2] for this mounting option. Wall anchors [A2] are used for solid concrete and brick installations only.
    Any material covering the wall must not exceed 5/8″ (16mm).
    Minimum wood stud size: 1 1/2″” W x 3 1/2″” D (38 x 89mm)

  1. Use a stud finder to locate wood studs, or use an awl to check the edges. Mark the edge and center positions.

  2. Position the arm assembly/ wall plate [05] at your desired height and line up the holes with your stud center line. Level the wall plate and mark the holes.

  3. Drill three pilot holes using a 7/32″ [5.5mm) diameter drill bit. Make sure the depth is not less than 2 3/4″ [70mm). Be sure to use the specified drill bit.

  4. Mount the arm assembly/ wall plate [05] on the wall using the lag screws [A 1 ]. Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtightenl.

  *  **OPTION 8: MOUNTING ON SOLID CONCRETE OR BRICK WALLS  

WARNING**
Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate (DO NOT overtightenl. Do not use a drill; only use a socket wrench. Use wall anchors [A2] for this mounting option.
Mount the arm assembly/ wall plate directly on the concrete or brick surface.
Minimum solid concrete thickness: 8″ [203mm] Never drill into the mortar between bricks.

  1. Position the arm assembly/ wall plate [05] at your desired height. Level the wall plate and mark the pilot holes.

  2. Drill 3 pilot holes using a 3/8″ [10mm) diameter drill bit. Make sure the depth is not less than 3″ [75mm). Never drill into the mortar between bricks.

  3. Use a hammer to tap the anchors [A2] into the drilled holes. Ensure the anchors are seated flush with the concrete or brick surface.

  4. Mount the arm assembly/ wall plate [05] on the wall using the lag screws [A 1] and anchors. Tighten the lag screws only until they are pulled firmly against the wall plate [DO NOT overtighten].

• STEP 3 TESTING TV WALL MOUNT INSTALLATION
  Before hanging the TV on the mount, pull down on the mount with your hands to check that it’s securely installed.

• STEP 4 ATTACHING THE FRONT SUPPORT TO THE ARM ASSEMBLY

1. Insert front support bars [02] and [03] into the arm assembly, then tighten bolts [G1] to secure them.

2. Attach end caps [04] onto the front support bars using bolts [G2].

• STEP 5 MOUNTING THE TV ON THE ARM ASSEMBLY/ WALL PLATE
  Hang the TV on the arm assembly/ wall plate using hooks on both brackets. Then flip the safety locks up and fasten using bolts [G3].

• STEP 6 ADJUSTING THE TILT ANGLE OF THE TV
  Slightly loosen the lever [T1l. Adjust the TV to your desired tilt angle. Retighten the lever [T1] to lock the tilt angle. If the tilt angle can·t be locked, tighten the nut [T2] using a socket wrench.
  NOTE: If the lever is blocked by the front support when turning, lift the lever up [as shown in figure “a”) then turn it again.

• STEP 7 LEVELING THE TV
  If needed, the TV can be levelled. Slightly loosen 4 leveling bolts [S1l. Level your TV. Retighten the leveling bolts IS 1] to hold the TV in place.

FREQUENTLY ASKED QUESTIONS

• How should I manage the cables?
  Use the cable ties.

• How can I raise/lower the TV if the TV Wall Mount is already fixed on the wall?

1. Remove the TV from the TV Wall Mount.
2. Remove the TV brackets from the TV and reattach according to instructions A or Bin the picture below [A for lifting up the TV or B for lowering the TV].
3. Hang the TV on the TV Wall Mount and secure.
  * To raise the TV by a few inches, reattach the TV brackets using the upper holes in the brackets.
  * To lower the TV by a few inches, reattach the TV brackets using the lower holes in the brackets.

• It’s too hard to adjust the swivel angle or extension of the TV Wall Mount.

1. Mount the TV and Wall Mount on the wall before trying to move the arms. Only move the TV by the left and right edges. Do not push on the screen of the TV.

2. If you have tried Option 1 but adjustment is still too hard, try lubricating the arm joints with a few drops of machine oil.

ABOUT COMAPNY

• 1-800-456-5231 [US/CA]
• Mon-Fri, 8am-8pm [CST]
• support@perlegear.com
• 44-808-196-4165 [UK]
• Mon-Fri, 2pm-1 0pm [UTC]
• www.perlegear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>