PERLEGEAR PGTVMC14 Rolling TV Stand Instruction Manual
- June 15, 2024
- Perlegear
Table of Contents
PERLEGEAR PGTVMC14 Rolling TV Stand
Before getting started, let’s make sure this cart is compatible.
- Is the VESA pattern of your TV 100 x 100mm (3.9 x 3.9″) to 400 x 400mm (15.7 x 15.7″)?
- Does your TV (including accessories) weigh less than 88 lbs (40kg) ?
- Tools Needed (NOT lncluded)
- Important Safety Information
NOTE
- Please carefully read all instructions before attempting installation. If you DO NOT understand the instructions or have any questions or concerns, please call technical support or email customer service.
- Not all hardware included in this package will be used.
CAUTION
- Avoid the risk of personal injury and property damage!
- DO NOT use this product for any purpose that is NOT explicitly specified in this manual. DO NOT exceed weight capacity. We are NOT liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
- Before starting assembly, verify all parts are included and undamaged. DO NOT use damaged or defective parts. lf you require replacement parts, please call technical support or email customer service.
WARNING
- This package contains small parts that may pose a choking hazard.
TIP-OVER WARNING
Serious or fatal crushing injuries can occur from a tip‐over accident. To help prevent a tip‐over accident:
- Never allow children to climb, stand, hang, or play on any part of the TV or TV cart.
- Use tip‐over restraints (not included) or anchors (not included) to attach the TV cart to the wall.
- Tip‐over restraints may reduce but not eliminate the risk of a tip‐over accident.
Supplied Parts and Hardware **
![PERLEGEAR-PGTVMC14-Rolling-TV-Stand-
fig-7]](https://manuals.plus/wp-content/uploads/2023/12/PERLEGEAR-PGTVMC14
-Rolling-TV-Stand-fig-7.jpg)
**
Installation
Step 1 Attach TV Brackets to TV
1-1 Select TV Bolts
Hand thread bolts into the threaded inserts on
the back of your TV to determine which bolt (M4, M6 or M8) to use. A minimum
of 4-5 turns into the threading is required. Do not turn past the bottom of
the hole.
1-2 Spacer and Bolt Configurations
1-3 Attach the TV Brackets to Your TV
Round holes should be directed toward the top.
Option A: For Flat Back TVs
Add spacers if needed to fit the bolt length
and TV back.
Option B: For Curved Back TVs
Spacers must be tall enough so that the curved
back of the TV does not interfere with the mounting plate.
Option C: For TVs With a Bump
The TV brackets must be flush on the bump and
leveled by spacers on the gap.
Option D: For TVs With Protruding Cables
Use spacers to create extra space
between the TV and TV
Option E: For TVs With Recessed Holes
Spacers need to fill in the recessed holes on
the back of the TV, while keeping the TV brackets as close to the TV as
possible.
Step 2 Install the Base
Insert the long square tubes [02] onto the side of base section [01] with droplet holes. Insert the short square tubes [03] onto the other side. Secure the tubes with bolts [a] and washers [b1].
NOTE: Flip the brakes down to avoid movement during assembly.
Screw the casters [04] into the base using the wrench [04-1].
Step 3 Secure the Poles to the Base
Insert lower poles [05] into the base and secure with bolts [a].
Insert bolts [c] into four pole connectors [08] as the front pole connectors.
Keep them for Step 3-3 and Step 3-4.
Place the middle poles [06] on top of the lower poles [05]. With the front
pole connec-tors attached, pass bolts [c] through the holes and thread them
into the other pole connectors [08] on the opposite side. Firmly tighten nuts
[b2] to secure the poles together.
Place the upper poles [07] on top of the middle poles [06]. Repeat steps from 3–3 using the pole connectors [08] to secure the upper and middle poles together
Step 4 Secure the TV Plate to the Upper Poles
The upper poles [07] have 5 height options. Determine the best height for your
TV before moving on to attach your TV to the poles.
Secure the TV plate [10] to the upper poles [07] with bolts [c] and nuts [b2].
Step 5 Hang the TV on the TV Plate
Hang the TV on the TV plate [10]. Retighten the bolts on the brackets until they are pulled firmly against the TV plate.
Step 6 Adjust the Tilt Angle of the TV
Slightly loosen nuts [T]. Adjust the TV to your desired tilt angle. Retighten nuts [T] to lock the tilt angle.
Step 7 Adjust the Height of the Casters
If the TV cart is not level on the floor, you can adjust the casters by turning the preassembled nuts for proper stability
Step 8 Cable Management
- 1-800-456-5231 (US/CA)
- 44-808-196-4165 (UK)
- support@perlegear.com
- WWW. www.perlegear.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>