Perlegear TV Cart PGTVMC05 Instruction Manual

June 7, 2024
Perlegear

Perlegea logo

TV Cart Instruction Manual
v2.0(A)

Perlegear TV Cart PGTVMC05 - 27

Thank you for choosing this Perlegear product! At Perlegear we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at Technical Support: (US/CA) 1-800-456-5231 Mon-Fri 8 am – 8 pm (PST) (USA) (CAN)
Other Info: support@perlegear.com(US/CA)

Important Safety Information

  • Please read through these instructions completely before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our customer service at support@perlegear.com.
  • Check package contents against Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact our customer service at support@perlegear.com.
  • Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
  • Serious or fatal crushing injuries can occur from tip over. PREVENT TIP-OVER:
  • Never allow children to climb, stand, hang, or play on any part of the TV or TV cart.
  • Use tip over restraint or anchor to attach the TV cart against the wall.
  • Use tip-over restraint or anchor stand to wall use of tip-over restraints may only reduce, but not eliminate the risk of tip over.

Weight Restrictions

The max load capacity of LCD/plasma screen:

WARNING
DO NOT exceed the maximum weight indicated. This TV cart is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the TV cart and its accessories, causing possible damage and or injury.

Check the VESA Pattern of TV Before the Installation

Perlegear TV Cart PGTVMC05 - 3 If your TV VESA is greater than 600×400 mm/24×16 in. or less than VESA 100x100mm/4×4 in., this mount is NOT compatible.
If this product is NOT compatible, please contact customer service atsupport@perlegear.com to find a compatible mount.

Tools Needed(Not Included)

Perlegear TV Cart PGTVMC05 - 4

Parts and Hardware Supplied

Perlegear TV Cart PGTVMC05 - 5Perlegear TV Cart
PGTVMC05 - 6

Secure the Castore on the Base

Turn the base upside down to keep the bottom side of the base upwards

Perlegear TV Cart PGTVMC05 - 7Lock the castors [12], then secure the four castors [12] on the base [01]

Perlegear TV Cart PGTVMC05 - 8
Turn the base upside down again to keep top side of the base upwards.

Perlegear TV Cart PGTVMC05 - 9

Connect Post Assembly to Base

Fasten the four bolts [A2] using ellen key [F2] to secure the height- adjustable post [03] on base [01]

Perlegear TV Cart PGTVMC05 - 10Perlegear TV Cart
PGTVMC05 - 13

Adjust the Height of the Post

Use thumb or finger to depress the spring ball of the right upper post located at the cable hole, meanwhile twist and pull the upper post upward to your desired height. As shown in fig-1, twist the upper post toward the plunger holes direction and engage the spring ball into the plunger hole to fix the post in place as shown in fig-2. Note: Repeat step 1 for the left post.

Warm Tip: While adjusting the height of the post, you can use the height label indicator on the pole as a guide

Perlegear TV Cart PGTVMC05 - 14

Secure the TV Plate to Height Adjustable Post

Perlegear TV Cart PGTVMC05 - 15

Secure the TV Brackets to the TV

Perlegear TV Cart PGTVMC05 - 16

Perlegear TV Cart PGTVMC05 - 17Perlegear TV Cart
PGTVMC05 - 18

Secure the TV to TV Plate

Perlegear TV Cart PGTVMC05 - 19Perlegear TV Cart
PGTVMC05 - 20

Secure AV Shelf to the Height Adjustable Post

Perlegear TV Cart PGTVMC05 - 21Perlegear TV Cart
PGTVMC05 - 22

Install the Camera Tray to the Height Adjustable Post

Perlegear TV Cart PGTVMC05 - 23Perlegear TV Cart
PGTVMC05 - 24

TV Height Re-set and Cables Management

9-1. It needs 2 men to re-set the TV height, “A” man holds the TV bottom with 2 hands as shown in Fig 1. 9-2. The “B” man depresses 2 spring balls [Si] with his thumbs, so that ‘A’ man can adjust TV down-wards or upwards to desire viewing height. Please note: you can use the height label indicator on the pole as a reference.
9-3. Attach the cable cover [1 1] to the cable windows as shown in Fig. 3. 9-4. Route cables and wires from upper cables windows to lower cables windows as shown in Fig 3 and 4.

Perlegear TV Cart PGTVMC05 - 26

Thank you again for choosing this Perlegear product!

Perlegear TV Cart PGTVMC05 - 27

All of us at Perlegear do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. If you have any questions please don’t hesitate to contact us at Technical Support: (US/CA)1-800-456-5231 Mon—Fri 8 am — 8 pm (PST) (USA) (CAN) Other Info: supportOperlegear.com(US/CA)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals