PERLEGEAR PGLT2 UL-Listed Tilting TV Wall Mount Instruction Manual

PERLEGEAR PGLT2 UL-Listed Tilting TV Wall Mount Instruction Manual

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the industry. If you have any installation questions or issues with the product, please contact us at the number below.

BEFORE GETTING STARTED

LET”S MAKE SURE THIS MOUNT IS PERFECT FOR YOU

TOOLS NEEDED

(NOT INCLUDED)

A NOTE ON SUPPLIED PARTS AND HARDWARE

  WARNING: This product contains small parts that may pose a choking hazard.
Before starting assembly, check all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Technical Support line as listed above or Customer Service at [email protected].

NOTE: Not all hardware included in this package will be used.

SUPPLIED PARTS AND HARDWARE

INSTALLATION

STEP 1: ATTACHING THE TV BRACKETS TO YOUR TV

STEP2: ASSEMBLING THE WALL PLATE

STEP3: MOUNTING THE WALL PLATE ON THE WALL

For mounting on wood stud walls, go to Option A.
For mounting on solid concrete, concrete block, or brick walls, go to Option B.

OPTION A: MOUNTING ON WOOD STUD WALLS
  IMPORTANT: Maximum horizontal distance between fasteners is 24″ [610mm).

• Avoid the risk of personal injury or property damage! Tighten the lag screws [A1] only until they are pulled firmly against the wall plate [DO NOT overtighten]. Do not use a drill; only use a socket wrench.
• Do not use wall anchors [A2] for this mounting option. Wall anchors [A2] are used for solid concrete, concrete block, and brick installations only.
• Any material covering the wall must not exceed 5/8″ [16mm].
• Minimum wood stud size: 1 1/2″ W x 3 1/2″ D [38 x 89mm].
• Wood stud spacing: 16″ to 24″ [center to center].

OPTION B: MOUNTING ON SOLID CONCRETE, CONCRETE BLOCK, OR BRICK WALLS

WARNING

• Avoid the risk of personal injury or property damage! Tighten the lag screws [A 1l only until they are pulled firmly against the wall plate [DO NOT overtighten]. Do not use a drill; only use a socket wrench. Use wall anchors [A2] for this mount­ing option.
• Mount the wall plate assembly [03] and [04] directly on the concrete surface.
• Minimum solid concrete thickness: 8″ [203mm].
• Minimum concrete block size: 8″ x 8″ x 16″ [203 x 203 x 406mm].
• Never drill into the mortar between blocks or bricks.

STEP4: TESTING TV WALL MOUNT INSTALLATION

Before hanging the TV on the mount, pull down on the mount with your hands to check that it’s securely installed.

STEP 5: MOUNTING THE TV ON THE WALL PLATE

5-1 Hang the TV on the wall plate assembly [03] and [04] using the brackets.

5-2 Press the bottom of the TV into the wall plate until the latches lock on the wall plate.

STEP 6: ADJUSTING THE TILT ANGLE OF THE TV

Tilt your TV to your desired angle and TV can stay in place.

Tip:
If it is too rigid to set the tilt angle, slightly loosen the tilt tension bolts [Tl until the TV can stay in place.
If your TV naturally tilts down, slightly tighten the tilt tension bolts [Tl until the TV can stay in place.

STEP 7: REMOVING THE TV

FREQUENTLY ASKED QUESTION

QUESTION 1: How can I raise/Lower the TV if the TV Wall Mount is already fixed on the wall?

1. Remove the TV from the TV Wall Mount.
2. Remove the TV brackets from the TV and reattach according to instructions A or Bin the picture below [A for lifting up the TV or B for lowering the TV].
3. Hang the TV on the TV Wall Mount and secure.

THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>