PERLEGEAR PGTVS25 Universal Swivel TV Stand Instruction Manual

TABLETOP TV STAND
INSTRUCTION MANUAL Rev 01
MODEL PGTVS25

PGTVS25 Universal Swivel TV Stand

Thank you for choosing this Perlegear product. We strive to provide you with the best quality products and service in the ndustry. If you have any nstallation questions or issues with the product, please contact us at the number below.
** 1-800-456-5231 (US/CA] Mon-Fri, 8am-8pm (CST] 44-808-196-4165 [UK] Mon-Fri, 2pm-10pm [UTC] support@perlegear.com
www.perlegear.com**

BEFORE GETTING STARTED, LET’S MAKE SURE THIS STAND IS COMPATIBLE.

1. Check VESA Pattern Compatibility|

Measurement Conversion
100mm = 3.9″ 300mm = 11.8″
200mm = 7.9″ 400mm = 15.7″
Minimum: 100 x 100mm [3.9 x 3.9″] Maximum: 400 x 400mm [15.7 x 15.7″] If this stand is not compatible, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.

---|---
2. Check Max Load| If your TV weighs more, this stand is NOT compatible.
WARNING
DO NOT exceed the Max load ndicated. Use with products heavier than the Max load may result in failure of the mount, which could cause damage or injury.
3. Tools Needed (NOT Included)| Phillips Screwdriver
4. Important Safety Information| • Please carefully read all instructions before attempting installation.
If you do not understand the instructions or if you have any questions or concerns, please contact our Technical Support line as listed above
or Customer Service at support@perlegear.com.
• Not all hardware included in this package will be used.
CAUTION: Avoid potential njuries and property damage!
• Do not use this product for any purpose that is NOT explicitly specified n this manual. Do not exceed the Max load. We’re not liable
for damage or injury caused by incorrect assembly, improper mount­ing, or nappropriate use.
• Before starting assembly, check all parts are included and undam­ aged. Do not use damaged or defective parts. If you require replace­
ment parts, please contact our Technical Support line as listed above or Customer Service at support@perlegear.com.
WARNING: This product contains small parts that may pose a choking hazard.
SAVE THESE INSTRUCTIONS.

01. TV Bracket
02. Tempered Glass Base
03. Support Pillar
04. Plastic Cover
05. TV Plate
A. Bolt
B. Steel Washer
C. Plastic Washer
D. Bolt
E. Safety Lock
F. Foot Pad
G. Cable Clip

Supplied Parts and Hardware

INSTALLATION

STEP 1 ATTACHING THE TV BRACKETS TO YOUR TV
SELECT TV BOLTS
Only one bolt size fits your TV.

Hand thread bolts nto the threaded inserts on the back of your TV to determine which bolt [M4, M6 or M8] to use. A minimum of 4-5 turns nto the threading is required. Do not turn past the bottom of the hole.
SPACER AND BOLT CONFIGURATIONS

ATTACH THE TV BRACKETS TO YOUR TV

Center the brackets on the back of your TV [top to bottom]. The TV brackets must be securely fastened in place.
OPTION A: FOR FLAT BACK TVS
Add spacers if needed to fit the bolt length and TV back.

OPTION B: FOR CURVED TVS
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

OPTION C: FOR TVS WITH A BUMP
The TV brackets must be flush on the bump and leveled by spacers on the gap.

OPTION D: FOR TVS WITH PROTRUDING CABLES
Use spacers to create extra space between the TV and TV brackets.

OPTION E: FOR TVS WITH RECESSED HOLES
Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.

STEP 2
ASSEMBLING THE BASE 

Attach foot pads [F] to the frosted side of the tempered glass base [02].
TIP: Leave a small gap between the edge of the base and the foot pads.

Attach the support pillar [03] to the tempered glass base [02] using plastic cover [04]. plastic washers [C]. steel washers [B]. and bolts [A].

STEP 3
CONNECTING THE TV PLATE TO SUPPORT PILLAR 

The support pillar has two height options. Choose the best height position for your TV before moving on to attach the TV plate [05] to the support pillar [03].

Connect the TV plate [05] to the front of the support pillar [03].

STEP 4
HANGING TV ON THE TV PLATE 

The TV brackets have three sets of hooks. Choose the appropriate hooks before moving on to attach your TV. The #1 hooks will position your TV lower while the #2 hooks will add extra height. The #3 hooks will position your TV the highest.
HEAVY! You may need assistance with this step
Note: Hang the TV in the center of the TV plate .

Insert the safety locks [E] into the upward-facing hooks located directly below the horizontal TV plate. Tighten bolts until they are secured against the bottom of the TV plate.
STEP 5
CABLE MANAGEMENT

STEP 6
ADJUSTING THE TILT ANGLE OF THE TV 

Tilt the TV to the desired angle. You may need to slightly loosen the bolts [D]. Retighten the bolts [D] to hold the TV in position.
STEP 7
SWIVEL ADJUSTMENT 

The TV can be swivelled manually. Only swivel the TV by the TV edges. Do not press on the screen. f it s difficult to swivel, remove the TV, then slightly loosen the preassembled bolts. Do not overloosen. Reattach the TV and swivel.

THANK YOU FOR CHOOSING THIS PERLEGEAR PRODUCT

1-800-456-5231 (US/CA] Mon-Fri, 8am-8pm (CST]
44-808-196-4165 [UK] Mon-Fri, 2pm-10pm [UTC]
support@perlegear.com
www.perlegear.com
860-02622-00 Rev 01

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>