PERLEGEAR PGTVMC09 Mobile TV Cart Instruction Manual

May 15, 2024
Perlegear

PERLEGEAR PGTVMC09 Mobile TV Cart Instruction Manual

PERLEGEAR PGTVMC09 Mobile TV Cart.JPG

PGTVMC09

FIG 2.JPG

Manufacturer: BESTQI INNOVATION (HONG KONG) TECHNOLOGY CO., LIMITED
Address: FLAT/RM 185 GIF HANG WAI IND CENTRE 6 KIN TAI ST TUEN MUN NT

Before getting started

let’s make sure this cart is compatible.

FIG 3 Before getting started.JPG

FIG 4 Before getting started.JPG

FIG 5 Before getting started.JPG

Contents

FIG 6 Contents.JPG

FIG 7 Contents.JPG

FIG 8 Contents.JPG

FIG 10 Contents.JPG

FIG 11 Contents.JPG

Step 1 Choose the Combination that Fits Your VESA Hole Pattern

FIG 12 Choose the Combination that Fits Your VESA Hole
Pattern.JPG

The extender brackets should connect to the faceplate as demonstrated on the upper left. Do ia=Y not fully tighten the bolts [G1] until Step 2 is finished.

FIG 13 Choose the Combination that Fits Your VESA Hole
Pattern.JPG

FIG 14 Choose the Combination that Fits Your VESA Hole
Pattern.JPG

FIG 15 Choose the Combination that Fits Your VESA Hole
Pattern.JPG

Step 2: Attach the Faceplate with Extender Brackets to TV

2-1 Select TV Bolts

FIG 16 2-1 Select TV Bolts.JPG

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt ma (M4, M6 or MB) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.

2—2 Spacer and Bolt Configurations

FIG 17 Spacer and Bolt Configurations.JPG

Flat Back TV (See Option A)

Curved TV (See Option B)

Bump (See Option C)

Cables (See Option D)

Recessed Holes (See Option E)

2-3 Attach the Faceplate with Extender Brackets to Your TV

FIG 19 2-3 Attach the Faceplate.JPG

Option A

FIG 20.JPG

Option B

FIG 21.JPG

Option B: For Curved TVs
OD spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

Option C

FIG 22.JPG

Option C: For TVs with a Bump

The faceplate must be flush on the bump and leveled by spacers on the gap.

Option D

FIG 23.JPG

Option D: For TVs with Protruding Cables
Use spacers to create extra space between the TV and faceplate.

Option E

FIG 24.JPG

Option E: For TVs with Recessed Holes
69 Spacers need to fill in the recessed holes on the back of the TV, while keeping the faceplate as close to the TV as possible.

When you finish securing the TV bolts into the TV, please remember to tighten the bolts [G1 ].

Step 3 Install the Base

FIG 26 Install the Base.JPG

To avoid movement, lock the casters with brake [05-2] during installation. Attach 2 casters -=n with brake [05-2] to the end without holes of the side base brackets [04]. Tighten the lower a=Y nut [05b] to fix the caster.

Note: Try to keep 4 casters on the same level.

FIG 27 Install the Base.JPG

Attach the middle base bracket [03] to the lower pole [06] with the drop- shaped hole facing the front.

FIG 28 Install the Base.JPG

FIG 29 Install the Base.JPG

Connect the base assemblies together.

Step 4 Install the Middle Pole

FIG 30 Install the Middle Pole.JPG

Attach the middle pole [07] with the drop-shaped hole facing the front.

Step 5 Connect the Upper Pole to the Middle Pole

FIG 31 Connect the Upper Pole to the Middle Pole.JPG

The pole has eight height options. Choose the best height position for your TV before moving ia=UI on to attach your TV to the pole.

FIG 32 Connect the Upper Pole to the Middle Pole.JPG

Insert the upper pole [08] and align it with the screw holes. Fix the nuts [M] with the wrench ia=Y [G4], then tighten the bolts [I] to secure the upper pole [08].

Step 6 Secure the TV to the Upper Pole

FIG 33 Secure the TV to the Upper Pole.JPG

Slightly tilt the connector for easier installation of the nut [M]. Slightly loosen the pre-assem- 69 bled upper nut [S], then attach the TV. Secure the TV by tightening the nut [M] and the upper nut [S].

Step 7 Adjust the Tilt Angle of the TV

FIG 34 Adjust the Tilt Angle of the TV.JPG

You can directly tilt your TV to your desired angle. If it is difficult to tilt the TV, slightly loosen m the tilt bolts [T], and then adjust your TV. To lock the tilt angle, fix the nuts with the wrench [G4] and retighten the bolts [T].

Step 8 Level the TV

FIG 35 Level the TV.JPG

Slightly loosen the nut [Ml. Level your TV, then retighten the nut [Ml to hold the TV in place.

FIG 36 Level the TV.JPG

If the TV cart is not level on the floor, adjust the upper nut t05aJ to raise or lower the cart. Then retighten the lower nut L05bJ to fix the casters.

1- 800-456-5231 (US/CA)
44- 808-196-4165(UK)

support@perlegear.com

www.perlegear.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals