PERLEGEAR PGTVS07-U Universal Swivel Table Stand Instruction Manual
- June 7, 2024
- Perlegear
Table of Contents
PGTVS07-U Universal Swivel Table Stand
Instruction Manual Rev02
PGTVS07
Tabletop TV Stand
PGTVS07-U Universal Swivel Table Stand
Before getting started, let’s make sure this stand is compatible.
- Is the VESA pattern of your TV 75 x 75mm (3″ x 3″) to 200 x 200mm (7 .9″ x 7 .9″) ?
- Does your TV (including accessories) weigh less than 44 lbs (20kg)?
- Tools Needed (NOT Included)
- Important Safety Information
NOTE
- Please carefully read all instructions before attempting installation. If you do not understand the instructions or f you have any questions or concerns, please call technical support or email customer service.
- Not all hardware included in this package will be used.
CAUTION
- Avoid the risk of personal injury or property damage!
- Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum weight capacity. We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.
- Before starting assembly, verify that all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
WARNING
· This product contains small items that may pose a choking hazard.
Contents
Step 1 Attach the Faceplate to the TV
1 -1 Select TV Bolts
Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, MS, M6 or MS) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.
1-2 Spacer and Bolt Configurations
Curved TV (See Option B)
Bump (See Option C)
Cables (See Option D)
Recessed Holes (See Option E)
1-3 Attach the Faceplate to Your TV
When attaching the faceplate [NJ to the back of the TV, ensure the down-facing hooks are pointing to the bottom of the TV and the faceplate [NJ is equally centered on the back of the TV. Option A
Option A: For Flat Back TVs
Add spacers if needed to felt the bolt length and TV back.
Option B
Option B: For Curved TVs
Spacers must be tall enough so that the curved back of the TV does not
interfere with the mounting plate.
Option C
Option C: For TVs with a Bump
The faceplate must be flush on the bump and leveled by spacers on the gap.
Option D
Option D: For TVs with Protruding Cables
Use spacers [G1] or [G2] to create extra space between the TV and faceplate.
Option E
Option E: For TVs with Recessed Holes
Spacers [G1] or [G2] need to fill in the recessed holes on the back of the TV,
while keeping the faceplate as close to the TV as possible.
Step 2 Assemble the Base
– Note: Kindly note that the tempered glass base is designed to show the shiny
glass side facing
‘ up. TIP: Leave a small gap between the edge of the glass and the foot pads.
Place foot pads [W] on the bottom of the tempered glass base [O] in the
corners. Note: Do Not overtighten the bolts [A].
Secure the support pillar [P] to the tempered glass base [O] using the trim
ring [Y], reinforcing Ill plate [R], and bolts [A]. Ensure the side of the
reinforcing plate [R] with paper faces the glass base [O].
Step 3 Attach the TV to the Support Pillar The support pillar has three
height options. Choose the best height position for your TV before moving on
to attach your TV to the pillar. Hang the TV on the support pillar [P].
Secure the TV to the support pillar [PJ using the washer [FJ and bolt [H].
Step 4 Cable Management
Step 5 Swivel Adjustment
The TV can be swivelled manually. Only swivel the TV by the TV edges. Do not press on the screen.
1-800-456-5231 (US/CA)
44-808-196-4165(UK)
[email protected]
www.perlegear.com
860-00928-00 Rev02
AMZLAB GmbH
Laubenhof 23,45326 Essen
[email protected]
**** THEMIS AR support ltd.
85 Great Portland St, London, United Kingdom.
[email protected]
Manufacturer: BESTQLINNOVATION (HONS HONG)
TEC HNG QS CO., LIMITED
Address: FLAT/RM 185 G/F HANG WAI IND CENTRE
6 KIN TAI ST TUEN MUN NT