Perlegear PGTVS05 Universal TV Stand Mount Instruction Manual
- June 14, 2024
- Perlegear
Table of Contents
- Supplied Parts and Hardware
- Step 1 Attach TV Brackets to TV
- Step 2 Assemble the Base
- Step 3 Connect Upper Support Pillar to Lower Support Pillar
- Step 4 Attach the Front Support Bars to the TV Plate
- Step 6 Hang the TV on the Front Support
- Step 7 Cable Management
- Step 8 Swivel Adjustment
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INSTRUCTION MANUAL
Rev00(A)
PGTVS05 Tabletop TV Stand
****| 1-800-456-5231 (US/CA)
44-808-196-4165 (UK)
---|---
| support@perlegear.com
supportjp@perlegear.com (JP)
| www.perlegear.com
Before getting started, let’s make sure this stand is compatible.
1 Is the VESA pattern of your TV 200 x 100mm (7.9 x 3.9″) to 600 x 400mm
(23.6 X 15. 7″)?|
---|---
2 Does your TV (including accessories) weigh less than 99 lbs (45 kg)?|
3 Tools Needed (NOT Included)|
4 Important Safety Information| [NOTE]
• Please carefully read all instructions before attempting installation.
If you DO NOT understand the instructions or have any questions or concerns,
please call technical support or email customer service.
• Not all hardware included in this package will be used.
[CAUTION] • Avoid potential injuries and property damage!
• DO NOT use this product for any purpose that is NOT explicitly specified in
this manual. DO NOT exceed weight capacity. We are NOT liable for damage or
injury caused by improper mounting, incorrect assembly or inappropriate use.
• Before starting assembly, verify all parts are included and undamaged. DO
NOT use damaged or defective parts. If you require replacement parts, please
call technical support or email customer service.
WARNING
• This product contains small items that may pose a choking hazard.
Supplied Parts and Hardware
Step 1 Attach TV Brackets to TV
1-1 Select TV Bolts
Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or MS) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.
1-2 Spacer and Bolt Configurations
1 -3 Attach TV Brackets to Your TV
Option A: For Flat Back TVs
Add spacers if needed to flt the bolt length and TV back.
Option B: For Curved TVs
Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.
Option C: For TVs with a Bump
The TV brackets must be flush on the bump and leveled by spacers on the gap.
Option D: For TVs with Protruding Cables
Use spacers to create extra space between the TV and TV brackets.
Option E: For TVs with Recessed Holes
Spacers need to fill in the recessed holes on the back of the TV, while keeping the TV brackets as close to the TV as possible.
Step 2 Assemble the Base
Attach the foot pads [01] on the bottom of the tempered glass base [02] in the
corners.
NOTE: The tempered glass base is designed to show the shiny glass side
facing up.
Tip: Leave a small gap between the edge of the glass base and the foot
pad.
Secure the lower support pillar [03] to the tempered glass base [02] using the
bottom pillar cover [02], washer with 2 holes [O4], and bolts [HJ.
NOTE: Attach the washer with 2 holes with the EVA pad facing the base.
Step 3 Connect Upper Support Pillar to Lower Support Pillar
Insert the upper support pillar [05] into the lower support pillar [03], and secure them with bolts [I]. Then attach the top pillar cover [04] to the end of the upper support pillar.
Step 4 Attach the Front Support Bars to the TV Plate
Insert the front support bars [07] and [08] into the TV plate [06], making sure the small holes on the ends of the bars all face back, then secure them by tightening bolts [I].
Secure the end caps [09] to the ends of the front support bars [07] and [08] by tightening bolts [L].
Step 5 Attach the Front Support Assembly to the Upper Support ep Pillar
The support pillar has three height options. Choose the best height position for your TV before moving on to attach your TV to the pillar.
Connect the front support to the front side of the pillar with the swivel assembly facing the pillar. The side with arrow on the TV plate should face outward.
Step 6 Hang the TV on the Front Support
Slightly loosen the pre-assembled bolts [SJ until both bolts [S] are seated flush with the plate.
Hang the TV on the front support using the hooks on the brackets.
Retighten bolts [SJ on the safety locks until they are pulled firmly against the front support.
Step 7 Cable Management
Step 8 Swivel Adjustment
If necessary, the front support with TV can be swiveled manually.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>