n-FAB HPD1584CC Podium Hoop Step Instruction Manual
- June 13, 2024
- n-FAB
Table of Contents
n-FAB HPD1584CC Podium Hoop Step
Product Information
- I-SHEET PART NUMBER: INST-00279
- PART NUMBER: HPD1584CC, HPD1594QC-6
- PRODUCT: PODIUM HOOP STEP
- APPLICATION: 15-18 RAM 1500-4500 CC QC
Hardware Description
- 8mm zinc u-nut – 6 pieces
- 8mm zinc bolt – 6 pieces
- 8mm zinc lock washer – 6 pieces
- 8mm zinc washer – 12 pieces
- 8mm black bolt – 6 pieces
- 8mm black washer – 6 pieces
- 8mm black ny-lock nut – 6 pieces
Parts Included
- Driver side step – 1 piece
- Passenger side step – 1 piece
- Mounting Bracket – 6 pieces
Product Usage Instructions
- Identify the driver side step.
- Install the (x6) mounting brackets to each attachment point on the main tube using the supplied M10x25 carriage bolts and M10 hex nuts. Leave them loose for now. Note that the brackets should attach to the backside of the mounting flange with the threaded end of the carriage bolt facing towards the rear of the step. The bends on the driver and passenger front bracket should point forward when mounted to the vehicle.
- If equipped, remove the OE steps. Then, locate the mounting holes. In some cases, there will be threaded inserts installed by the factory. If not, insert the provided U nuts in the upper mounting holes.
- Carefully place the step into place. Begin with the center bracket and hand tighten the upper bolt and washer to hold it in place. Note that an assistant is recommended for this step. Next, insert and hand tighten the front and rear upper bolts and washers.
- Insert the black bolt with zinc washer from the back through the pinch weld of the vehicle. On the front, add a black washer and a black Nyloc nut.
- Begin tightening the nuts and bolts in an alternating pattern. Avoid using power tools. Tighten them to 20 ft./lbs. torque and secure the step to the truck.
- After final adjustment, tighten all three brackets at the main tube.
- Repeat steps 3-6 for the passenger side.
- I-SHEET PART NUMBER: INST-00279
- PART NUMBER: HPD1584CC, HPD1594QC-6
- PRODUCT: PODIUM HOOP STEP
- APPLICATION: 15-18 RAM 1500-4500 CC QC
|
---|---
HARDWARE DESCRIPTION
| QTY.
| 8mm zinc u-nut| 6
| 8mm zinc bolt| 6
| 8mm zinc lock washer| 6
| 8mm zinc washer| 12
| 8mm black bolt| 6
| 8mm black washer| 6
| 8mm black ny-lock nut| 6
PARTS INCLUDED
| QTY
---|---
Driver side step| 1
Passenger side step| 1
Mounting Bracket| 6
Installation Instructions
Step 2. Install the (x6) mounting brackets to each attachment point on
the main tube using the supplied M10x25 carriage bolts, M10 hex nuts and leave
loose for now.
NOTE: The brackets will attach to the backside of the mounting flange
with the threaded end of the carriage bolt facing towards the REAR of the
step.
NOTE: The bends on the driver and passenger front bracket will point forward when mounted to vehicle.
Step 3. Remove OE steps if equipped then locate mounting holes. In some cases, there will be threaded inserts installed by factory. If not, insert the provided U nuts in upper mounting holes.
Step 4. Carefully place step into place. Begin with center bracket and hand tighten the upper bolt and washer to hold in place. NOTE: An assistant is recommended for this step. Next, insert and hand tighten front and rear upper bolts and washer.
Step 5. Inset black bolt with zinc washer from the back then through the pinch weld of the vehicle. On the front, add black washer and black Nyloc nut.
Step 6. Begin tightening nuts and bolts in a alternating pattern. Avoid using power tools. Tighten to 20 ft./lbs. torque and secure the step to the truck.
Step 11. After finial adjustment, tighten all three brackets at the main tube.
Repeat steps 3-6 for passenger side.
CONTACT
- 12302 Shiloh Church Rd.
- Houston TX 77066
- Phone 281-880-6322
- Fax 281-880-6325
- n-fab.com.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>