n-FAB HWKT-07323X Hoop Step Instruction Manual
- June 13, 2024
- n-FAB
Table of Contents
n-FAB HWKT-07323X Hoop Step
Product Information
- Product: Hoop Step
- Application: 1999-2016 Ford F-250/350
- Compatible Cab Models: Regular Cab, Quad Cab, and Crew Cab
Hardware Description:
- HWKT-07323X
- HHCS-00568X 3/8-16 X 1
- FLTW-00663X 3/8 USS FLAT WASHER
- CLIP-00646X
- CARB-00680X
- HXNT-00717X
Parts Included:
- Driver side step – Quantity: 6
- Passenger side step – Quantity: 6
Product Usage Instructions
- Step 1: Identify the driver side step using the following codes:
- F9973QC
- F9984QC
- F99100CC
- F9984CC
- F99100QC
- F99105CC-6
- F99115CC-6
- F11111CC
- F9946RC
- F99100QC-6
- F99115CC
- F9995QC-6
- F11114CC-6
- F9984RC-4
- Step 2: Starting with the driver side, locate the holes for the upper mounts (x3) and install the supplied (x2) 3/8 clips in each position. Note that for Crew Cab models, there will be four attachment points, while for Quad Cab and Regular Cab models, there will be five attachment points. Only three attachment points will be used for the installation.
- Step 3: Attach the driver side step to the upper mounts using the provided hardware. The nut and washer will be only visible from underneath the vehicle.
- Step 4: After final adjustment, tighten all hardware to 17-20 ft/lbs of torque.
- Step 5: Repeat the process for the passenger side step.
Please note that this information is based on the user manual dated November 14, 2019. For any further inquiries or clarifications, please contact us at: 12302 Shiloh Church Rd. Houston TX 77066
- Phone: 281-880-6322
- Fax : 281-880-6325
- I-SHEET NUMBER: INST-00202
- PART NUMBER : All REG CAB QUAD CAB AND CREW CAB MODELS
- PRODUCT : HOOP STEP
- APPLICATION : 99-16 FORD F-250/350
HARDWARE DESCRIPTION
HARDWARE DESCRIPTION | QTY. |
---|
HWKT-07323X
HHCS-00568X| 3/8″-16 X 1″| 6
FLTW-00663X| 3/8″ USS FLAT WASHER| 12
CLIP-00646X| 3/8″-16 X 3/4″ BARREL NUT
CLIP
| 6
CARB-00680X| 3/8″-16 X 1-1/2″ GRADE 5
CARRIAGE
| 6
HXNT-00717X| 3/8″-16 GRADE 5 FINISHED
HEX NUT
| 6
PARTS INCLUDED
PARTS INCLUDED | QTY |
---|---|
Driver side step | 1 |
Passenger side step | 1 |
INSTALLATION
- STEP 1: Identify driver side step.
- Step 2: Starting with the Driver side, locate the holes for the upper mounts (x3) and install the supplied (x2) 3/8” clips in each position. NOTE: There will be four attachment points for the Quad Cab and five for the Crew Cab. Only three will be used for the installation. See below for your cab configuration.
- Step 3: Next, install the step aligning the brackets to the upper clips using the 3/8”x1” Hex bolt, 3/8’ USS Flat washer for the upper attachment and the 3/8”x 1 ½” carriage bolt 3/8” Hex nut, and 3/8” USS washer for the lower attachment. Leave it loose for now. NOTE: The carriage bolts will start from the outside of the body, and the nut and washer will be only visible from underneath the vehicle.
- Step 4: After final adjustment, tighten all hardware to 17-20 ft/lbs of torque.
- Step 5: Repeat the process for the passenger side.
12302 Shiloh Church Rd. Houston TX 77066 Phone
281-880-6322 – Fax
281-880-6325
REVISION – – © 2018 N-FAB, INC. REVISION DATE 11/14/19
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>