Kimberly-Clark ICON Automatic Roll Towel Narrow Recessed Dispenser User Guide
- June 3, 2024
- Kimberly-Clark
Table of Contents
Automatic Roll Towel Narrow Recessed Dispenser
User Guide
ICON Automatic Roll Towel Narrow Recessed Dispenser
ICON Automatic Roll Towel Narrow Recessed Dispenser Housing without Trim Panel – User Guide.
Use of this Dispenser
Not recommended for outdoor installation or in wet environments. Do not
attempt to clean the dispenser with a water jet or by spraying the dispenser
directly. Follow the installation and usage instructions. Only use genuine
Kimberly-Clark Professional product refills intended for the specific model.
The dispenser can be cleaned using a damp cloth and detergent, do not use
abrasive cleaning products.
Use Caution, Edges may be sharp when dispenser is open or during faceplate
installation.
Need more information?
These instructions and additional resources are available at
www.kcprofessional.com.
General Safety Information
This dispenser can be used by children over the age of 8 years old and persons
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, provided they have been given supervision or instruction
concerning use of the dispenser by a person responsible for their safety.
Access to the service area is restricted to persons who have knowledge and
practical experience of the dispenser, in particular as far as safety and
hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such.
Children shall not perform cleaning or user maintenance of this dispenser.
High-risk individuals are not expected to use this dispenser safely unless
continuous supervision is given.
- Not Included
** For additional faceplates, contact your sales representative.
**** Dispenser Access
- To unlock the dispenser, insert key into lock and rotate the key a quarter turn towards the wall. Gently pull the cover forward.
- Support the cover while opening.
Cover Removal
Remove dispenser cover before installing the cage. Refer to Dispenser
Access section for instructions to unlock the dispenser.
- Remove the cover by closing it about halfway. Align bottom edge of cover with vertical alignment line. The slot feature on the inside of the cover should line up with it’s corresponding slot on the ****dispenser body, allowing the cover to be flexed off.
- Remove the cover.
Cage Installation
When installing the dispenser ensure to follow all appropriate safety
precautions and wear proper safety equipment including gloves.
Note: This unit is for an install with studs on 16 inch centers or less.
For push buttons and other available parts, contact your sales
representative.
Tools Required**
Cage Installation
-
Find the key to the current dispenser and open the towel dispensing area.
-
Locate the screws holding the unit to the wall; there are usually 2 screws on each side and one on top, but this can vary so check to make certain you find all of the screws.
Cage Installation (continued)
-
Remove the screws from both sides and the top of the towel unit.
-
Remove the towel dispenser from the wall, this part will no longer be needed for this installation.
-
Check to see if the trash can unit is installed with screws on the proper framing. If not, that will need to be addressed before moving forward with the installation.
-
Check to see that the trash can installation is level.
-
Add the housing assembly to the top part of the trash can system.
-
Check the level of the dispenser before adding the screws to the installation.
-
Add the installation screws to the slotted areas on the side of the new recessed towel dispenser. Do not overtighten.
Module Installation for Recessed Dispensers
For instructions on how to install the module into a wall-mounted Roll Hand
Towel Dispenser, please refer to the Automatic Roll Towel Dispenser
instructions found on
www.kcprofessional.com.
Note: Install the housing assembly into the wall before installing the
module. For instructions on how to install the housing assembly, go to
www.kcprofessional.com.
- Remove the cover by closing it about halfway. Align bottom edge of cover with vertical alignment line. The key feature on the inside of the cover should line up with it’s corresponding slot on the dispenser body, allowing the cover to be flexed off.
- Remove the cover.
- Once the housing assembly is installed, align the back of the module with the angled posts on the back wall and lower into position. Ensure that the module is level once positioned.
- Insert screws, one on each side, to secure the module in its position inside the dispenser shell.
- Replace the cover by lining up the slot feature on the inside of the cover with its corresponding slot on the housing assembly in order to snap the cover back on. Allow the cover to fall open once replaced. 6.
- Insert the cable jack into the module (cable shown in red).
- See Module Installation Manual for next steps to install.
See Module Installation Manual for next steps to install.
Do Not Flush
Label Placement Recommendation
Flushing of non-flushable products, such as paper towels, can cause internal
plumbing issues as well as issues in municipal sewage systems.
To help avoid such issues, Kimberly Clark Professional* provides “Do Not
Flush” labels for stainless steel dispensers.
These labels have a non-permanent adhesive and may be removed at a later date
if desired.
Legal
®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW
®/™ Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses filiales.
© KCWW
Parts made in Mexico and China, Assembled in Mexico.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>