Kimberly-Clark Standard Roll Toilet Paper Dispenser 2 Roll Vertical User Guide
- June 3, 2024
- Kimberly-Clark
Table of Contents
Standard Roll Toilet Paper Dispenser
2 Roll Vertical User Guide
- Faceplate**
- Cover
- Backplate
- Bracket
- Bath Tissue*
Use of this Dispenser
Not recommended for outdoor installation or in wet environments. Do not
attempt to clean the dispenser with a water jet or by spraying the dispenser
directly. Follow the installation and usage instructions. Only use genuine
Kimberly-Clark Professional product refills intended for the specific model.
The dispenser can be cleaned using a damp cloth and detergent, do not use
abrasive cleaning products.
These instructions are available at www.kcprofessional.com.
General Safety Information
This dispenser can be used by children over the age of 8 years old and persons
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, provided they have been given supervision or instruction
concerning use of the dispenser by a person responsible for their safety.
Access to the service area is restricted to persons who have knowledge and
practical experience of the dispenser, in particular as far as safety and
hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless continuous supervision is given.
*For additional faceplates, contact your sales representative.
Not Included
Need more information?
These instructions and additional resources are
available at www.kcprofessional.com.
Install Dispense
Enclosed**
(x4) (x4)
For push buttons and other available parts, contact your sales representative.
Tools Required:
*Check for regional & local installing/ mounting requirements.
Mount the toilet paper dispensers to be 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the water closet measured to the centerline of the dispenser.
The outlet of the dispenser shall be 15 inches (380 mm) minimum and 48 inches (1220 mm) maximum above the finished floor. For the ICON dispenser, the center of the install bracket is the center of the dispenser.
See the module installation manual for the next installation steps.
1. Measure 32 ½ inches from the floor with a tape measure to the bottom of
the mounting bracket. Make sure the built-in level on the bracket reads level.
Ensure the required clearance space is free of obstructions for proper
dispenser installation.
2. Carefully brace the mounting bracket in place once it is properly located
on the wall and mark holes to drill.
3. Remove the bracket from the wall, leaving just the four marked holes.
Drill a hole in each of the four marked locations so anchors** can be
inserted.
4. Tap in the four anchors in each drilled hole so the bracket can be screwed
to the wall.
5. Bring back the mounting bracket and insert a screw into each wall anchor
to secure the mounting bracket to the wall. Screw the mounting bracket to the
wall starting with the marked anchor hole.
Make sure not to over-tighten the screw and damage the bracket!
** Ensure that proper mounting hardware is used for appropriate wall composition as enclosed hardware may not be compatible with your wall surface.
Install Dispenser
1. Carefully line the mounted wall bracket up to the rear, corresponding bracket pocket of the dispenser backplate to complete installation.
1
2. Once the mounting bracket is in its designated, corresponding pocket, lower the dispenser backplate until the lock button clicks.
2a 2b
3. Fasten the security screw to completely secure the dispenser to the mounting bracket. Do not over-tighten the security screw!
3
This is so that the dispenser does not inadvertently become separated from the bracket.
Remove Dispenser
1. To remove the dispenser backplate, first remove the security screw.
1
2. Next, press the lock button and lift the dispenser at a 45 degree angle to disengage it from the bracket.
2
Dispenser Access
1. To unlock the dispenser, insert key into lock and rotate the key a quarter turn. Gently pull the cover forward.
1
2. Support the cover while opening.
2
3. To lock, close the cover.
The dispenser will lock automatically without the key if the lock is returned
to the lock postition.
3
Cover Removal
1. Open the dispenser cover. Once opened, use a flathead screwdriver to push and remove the two pins inside the hinge of the dispenser cover.
1
2. When the hinge pins are removed, hold the sides of the dispenser cover for it will be free from the dispenser backplate to be removed.
2
Replace the dispenser cover by re-inserting the bottom hinge features of the cover into the hinge features of the backplate. When the features are engaged, insert each pin to secure the cover. Rotate up to close.
Load Product
1. Remove and discard the depleted soft bath tissue roll(s) if present.
2. Flex the spring-loaded roll holders on the left outward, like shown, and
insert the new soft bath tissue rolls into the right side core plugs.
3. Let the left roll holders flex back into the soft bath tissue roll core to
secure the rolls.
4. Close the dispenser cover, ensuring that the cover is securely locked
before removing hand.
Legal
®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW
Made in Mexico/ Fabrique au Mexique/ Fabricado en Mexico
Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA
30076-2199
Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5
Kimberly-Clark Europe Limited,
40 London Road, Reigate, Surrey, RH2 9QP, UK
www.kcprofessional.com + 44 (0) 1737 736000
Distributed in the Netherlands
Kimberly-Clark B.V., Copernicuslaan 35, 6716 BM Ede, Netherlands
Distributed in Australia by: Kimberly-Clark Australia Pty. Limited,
Kimberly-Clark Australia Pty Limited 100 Arthur Street North Sydney NSW 2060
Distributed in Hong Kong by: Kimberly-Clark (Hong Kong) Ltd. G.P.O. Box 8538,
Hong Kong Tel:(852) 2355 8640 E-Mail: kcphk@kcc.com
Distributed in Singapore by : Kimberly-Clark Singapore Pte. Ltd., 81 Tuas
South Avenue 8, Singapore 637558
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>