Kimberly-Clark Standard Roll Toilet Paper Dispenser 4 Roll User Guide

: June 3, 2024
: Kimberly-Clark

Table of Contents

Use of this Dispenser
General Safety Information
Install Bracket
Load Product
Legal
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Standard Roll Toilet Paper Dispenser 4 Roll
User Guide Kimberly Clark Standard Roll Toilet
Paper Dispenser 4 Roll - Figure 1

Use of this Dispenser

Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser with a water jet or by spraying the dispenser directly. Follow the installation and usage instructions. Only use genuine Kimberly-Clark Professional product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and detergent, do not use abrasive cleaning products.
These instructions are available at www.kcprofessional.com.

General Safety Information

This dispenser can be used by children over the age of 8 years old and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the dispenser by a person responsible for their safety. Access to the service area is restricted to persons who have knowledge and practical experience of the dispenser, in particular as far as safety and hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless continuous supervision is given.
*For additional faceplates, contact your sales representative.
Not Included
Need more information?
These instructions and additional resources are available at www.kcprofessional.com.

Install Bracket

Tools Required:

Kimberly Clark Standard Roll Toilet Paper Dispenser 4 Roll - Figure
3

Enclosed**

For push buttons and other available parts, contact your sales representative.

Mount the toilet paper dispensers 7 inches (180 mm) minimum and 9 inches (230 mm) maximum in front of the toilet measured to the interline of the dispenser.
The bottom of the dispenser shall be 15 inches (380 mm) minimum and 48 inches (1220 mm) maximum above the finished floor. For the ICON™ dispenser, the centre of the install bracket is the centre of the dispenser.

*Check for regional & local installing/mounting requirements.**

Align bracket to local ADA required distance from floor + 2 3/8” (6 cm).
This will ensure the bottom of the dispenser is at the correct ADA required height. Make sure the built-in level on the bracket reads level. Ensure the required clearance space is free of obstructions for proper dispenser installation.
Carefully brace the mounting bracket in place once it is properly located on the wall and mark holes to drill.
Remove the bracket from the wall, leaving just the four marked holes. Drill a hole in each of the four marked locations so anchors can be inserted.
Tap in the four anchors in each drilled hole so the bracket can be screwed to the wall.
Ensure that proper mounting hardware is used for appropriate wall composition as enclosed hardware may not be compatible with your wall surface.
Bring back the mounting bracket and insert a screw into each wall anchor to secure the mounting bracket to the wall. Screw the mounting bracket to the wall starting with the marked anchor hole. Make sure not to over-tighten the screw and damage the bracket!

Install Dispenser

Carefully line the mounted wall bracket up to the rear, corresponding bracket pocket of the dispenser back-plate to complete installation.
Once the mounting bracket is in its designated, corresponding pocket, lower the dispenser back-plate until the lock button clicks.
Fasten the security screw to completely secure the dispenser to the mounting bracket. Do not over-tighten the security screw!
This is so that the dispenser does not inadvertently become separated from the bracket.

Load Product

Remove and discard the depleted soft bath tissue roll(s) if present.
Flex the spring-loaded roll holders on the left and right out, like shown, and insert the new soft bath tissue rolls into the right side core plugs.
Let the spring-loaded roll holders flex back into the soft bath tissue roll core to secure the new rolls.
Close the dispenser cover, ensuring that the cover is securely locked before removing hand.

Legal

®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW
Parts made in Mexico and China, Assembled in Mexico
Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199
Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5
Kimberly-Clark Europe Limited, Walton Oaks, Dorking Road, Tad worth, Surrey, KT20 7NS, UK. www.kcprofessional.co.uk
Kimberly-Clark B.V., Copernicus 35, 6716 BM Ede, Netherlands. www.kcprofessional.fr (FR) or www.kcprofessional.de (DE)
Distributed in Australia by Kimberly-Clark Australia Pty. Ltd, Level 4, 100 Arthur Street, North Sydney, NSW 2060 Tel: 1800 647 994 www.kcprofessional.com.au
Distributed in New Zealand by Kimberly-Clark New Zealand, Level 2, 123 Carlton Gore Road, Newmarket, Auckland 1023, New Zealand Tel: 0800 447 814 www.kcprofessional.co.nz
Distributed in Singapore by Kimberly-Clark Singapore Pte. Ltd, 81 Tuas South Avenue 8, Singapore 637558. Tel: 1 800 562 5275 www.kcprofessional.com.sg

Kimberly Clark Standard Roll Toilet Paper Dispenser 4 Roll - Figure
12 | Kimberly Clark Standard
Roll Toilet Paper Dispenser 4 Roll - Figure 13
---|---