Kimberly-Clark ICON Automatic Soap and Sanitizer Dispenser User Guide

Kimberly-Clark ICON Automatic Soap and Sanitizer Dispenser User Guide

Use of this Dispenser

Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser with a water jet. Follow the installation and usage instructions. Only use genuine Kimberly-Clark Professional product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and detergent, do not use abrasive cleaning products.

These instructions are available at www.kcprofessional.com.

General Safety Information

This dispenser can be used by children over the age of 8 years old and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the dispenser by a person responsible for their safety. Access to the service area is restricted to persons who have knowledge and practical experience of the dispenser, in particular as far as safety and hygiene are concerned.

This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless continuous supervision is given.

Tools Required

Enclosed

For push buttons and other available parts, contact your sales representative.

Install Bracket

1. Measure 15 9/16 inches from the counter top or back splash with a tape measure to the bottom of the mounting bracket. Make sure the built-in level on the bracket reads level. Ensure the required clearance space is free of obstructions for proper dispenser installation. Check for regional & local installing/mounting requirements.
   

2. Carefully brace the mounting bracket in place once it is properly located on the wall and mark holes to drill.
   

3. Remove the bracket from the wall, leaving just the four marked holes. Drill a hole in each of the four marked locations so anchors can be inserted.
   

4. Tap in the four anchors in each drilled hole so the bracket can be screwed to the wall.
   

5. Bring back the mounting bracket and insert a screw into each wall anchor to secure the mounting bracket to the wall. Be sure to screw the mounting bracket to the wall starting with the top right hole.
   
   Make sure not to over-tighten the screw and damage the bracket.
   Ensure that proper mounting hardware is used for appropriate wall composition as enclosed hardware may not be compatible with your wall surface.

Install Dispenser

1. Carefully line the mounted wall bracket up to the rear, corresponding bracket pocket of the dispenser backplate to
   complete installation.
   

2. Once the mounting bracket is in its designated, corresponding pocket, lower the dispenser backplate until the lock button clicks.
   

3. To remove the dispenser backplate, press the lock button and lift the dispenser off of the bracket.
   

Dispenser Access

1. To unlock the dispenser, insert key into lock and rotate the key a quarter turn. Gently pull the cover forward.
   

2. The key may be removed at this point. The cover will automatically open, do not force.
   

3. Once the cover has opened fully, a secondary door at the bottom of the dispenser will open automatically.
   

Replace Batteries

1. To load batteries, depress the battery lid tabs and lift to the side.
2. Remove all depleted batteries if present.
3. Insert new batteries ensuring polarity is correct.
4. Align tabs on battery cover to front of battery compartment opening and push to engage.
   

Battery Information

• 3 D type 1.5V alkaline batteries required.
• Change all 3 batteries at the same time, do not mix types or brand of batteries.
• Please follow the battery insertion instructions ensuring polarity is correctly aligned.
• Used batteries are to be disposed of safely and follow local environmental policy for disposal.
• Do not short circuit the supply terminals of the battery or the dispense.

Load Product

1. Remove and discard depleted product cassette if present.
2. Remove and discard nozzle cap of new product cassette.
3. Place new cassette into dispenser module by aligning features on both. Push the cassette towards the back of the dispenser.
4. Close the dispenser cover,  ensuring that the cover is securely locked before removing hand. Dispense product to confirm proper loading.
   

Alerts

Low Product

When new product needs to be added, the droplet icon will illuminate on the front of the  closed dispenser. Once the dispenser has been opened, a yellow led will be lit until the product cartridge is replaced with a new unit.

Low Battery

When the battery is low, the exterior battery light and interior LED will blink.

Support

®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW
Distributed in Singapore by: Kimberly-Clark Singapore Pte. Ltd., 81 Tuas South Avenue 8, Singapore 637558 E-Mail: Singapore.kpc@kcc.com
www.kcprofessional.com

References

• Restroom, Safety & Wiping Products Workplaces Trust | Kimberly-Clark Professional

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>