Kimberly-Clark 09551 Jumbo Twin Roll Toilet Paper Dispenser Instruction Manual

June 1, 2024
Kimberly-Clark

Kimberly-Clark 09551 Jumbo Twin Roll Toilet Paper Dispenser

Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser-
PRODUCT

Specifications

  • Product Name: JUMBO TWIN ROLL TOILET PAPER DISPENSER
  • Product Code : 09551
  • Compatible Roll Sizes: Two 9″ diameter rolls or one standard 12″ diameter roll plus stub roll
  • Tools Required: Drill bit for anchor size, mounting screws

Product Usage Instructions

Adjusting Roll Holder Hubs

  1. Determine the size of the jumbo tissue to be used.
  2. To switch to 12″ roll and stub roll, depress the hub locking pin and rotate the hubs accordingly.
  3. To make adjustments after installation, loosen the mounting screws and pull the unit from the wall slightly.

Installation Process

  1. Position roll holders for the intended product size before mounting.
  2. Assess the wall material to determine if screw anchors are needed.
  3. Mount the dispenser at the appropriate height and distance from the toilet.
  4. Use a minimum of 4 mounting screws for a secure installation.

Optional Push Button Lock Feature

  1. To convert to push-button operation, carefully remove the plug and follow the steps provided.

Loading Instructions

  1. Open the dispenser using the key or push button.
  2. For 12″ rolls, move a partially completed roll to the stub roll position and load a new roll in the primary position.

FAQ

  • Q : Can the roll holder hubs be adjusted after installation?
  • A : Yes, but it requires loosening the mounting screws and pulling the unit slightly from the wall to access the hub locking pins.
  • Q: How many mounting screws should be used for installation?
  • A: A minimum of 4 mounting screws are recommended to attach the dispenser securely to the wall.
  • Q : How do I convert the dispenser to push-button operation?
  • A: Follow the provided instructions to carefully remove the plug and insert the push button accordingly.

DEMENSION

ROLL HOLDER POSITIONING

Enclosed

Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser-
FIG-2

Tools Required

Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser-
FIG-3

For available spare parts, contact your sales representative.
This dispenser is equipped with adjustable roll holder hubs that allow it to dispense two different sizes of Jumbo Roll Tissue

  • either two full 9” diameter rolls, or one standard 12” diameter roll plus stub roll.
  1. First, determine which size Jumbo Roll Tissue product will be used with this dispenser. The dispenser comes pre-loaded from the factory for two 9” Jumbo Tissue Rolls (Figure 1).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-4
  2. If for use with 12” tissue rolls and stub roll, move the hubs by depressing the hub locking pin (Figure 2). Rotate one hub to the 12” position until it clicks and locks. Rotate the other hub to the stub roll position until it clicks and locks. (It is recommended that the 12” roll be located farthest away from the user when the dispenser is installed).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-5

Please Note: Once the dispenser is installed the hub positions can only be changed by loosening the mounting screws and pulling the unit approximately a quarter inch from the wall so that the hub locking pin can be depressed in. Once the adjustment is made the mounting screws are then retightened.

Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser-
FIG-6Kimberly-Clark 09551
-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-7

Installation

IMPORTANT! For secure mounting, follow these instructions thoroughly. Ensure that the proper mounting hardware is used for the appropriate wall type.

Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser-
FIG-8

  1. Prior to mounting, ensure the roll holders are positioned for the product that is to be used. (See hub adjustment instructions).

  2. Assess wall surface material to determine if screw anchors are required.

  3. Mount the dispenser with the bottom edge approximately 15-48” from the floor and
    7- 9” from the front edge of the toilet to the centerline of the dispenser. In the presence of a grab bar rail, mount dispenser so that the outlet is no greater than 12” above the bar, or so that the top of the dispenser is no less than 1.5” below the bar.

  4. Use 4 mounting screws as a minimum to attach the dispenser to a wall.

OPTIONAL PUSH BUTTON LOCK FEATURE

Dispenser comes with plug in place. To convert to a pushbutton operation:

  1. Depress the end of the metal lock spring being careful not to overstress it. Remove the plug, if one is installed, by pushing on it from the inside (Figure 1).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-9
  2. Remove one of the push buttons from the back wall of the dispenser (Figure 2).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-10
  3. Insert the pushbutton into hole from inside of dispenser (see Figure 3). Insert metal lock spring back in place, lining up notches on it with ones on back panel. Push the bottom tab of lock spring up until it snaps into place.Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-11

Loading Instructions

  1. Open the dispenser using the provided key or push button (Figure 1).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-12
  2. For 12” rolls, a partially-completed roll can be moved to the stub roll position, and a new roll can be loaded in the primary position.
  3. Close firmly and ensure the cover latches (Figure 2).Kimberly-Clark 09551-Jumbo-Twin-Roll-Toilet-Paper-Dispenser- FIG-13

AMERICANS WITH DISABILITIES ACT (for use in the U.S. only): Title 111 of the Americans with Disabilities Act (“ADA”) governs, in detail, the placement and operation of dispensers. You should ensure that your mounting and use of dispensers complies with that law as well as the regulations issued under that statue. The mounting suggestions in this document may or may not fulfill the obligations of the ADA with respect to your facility.Kimberly-Clark Corporation DISCLAIMS LIABILITY FOR PERSONAL INJURIES OR PROPERTY DAMAGES RESULTING FROM INSTALLATIONS NOT PERFORMED BY Kimberly-Clark.
®/™Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. ®KCWW is a registered trademark of Kimberly-Clark Tissue Company. ®1998 KCC. All Rights Reserved. Manufactured for: Kimberly-Clark Corporation, Roswell, GA 30076.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Kimberly-Clark User Manuals

Related Manuals