Kimberly-Clark ICON Automatic Roll Towel Recessed Dispenser Housing with Trim Panel User Guide

Kimberly-Clark ICON Automatic Roll Towel Recessed Dispenser Housing with

Trim Panel

Automatic Roll Towel Recessed Dispenser Housing with Trim Panel – User Guide

Use of this Dispenser

Not recommended for outdoor installation or in wet environments. Do not attempt to clean the dispenser with a water jet or by spraying the dispenser directly. Follow the installation and usage instructions. Only use genuine Kimberly-Clark Professional product refills intended for the specific model. The dispenser can be cleaned using a damp cloth and detergent, do not use abrasive cleaning products.

Use Caution, Edges may be sharp when dispenser is open or during faceplate installation.

Need more information?
These instructions and additional resources are available at www.kcprofessional.com.

General Safety Information

This dispenser can be used by children over the age of 8 years old and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the dispenser by a person responsible for their safety. Access to the service area is restricted to persons who have knowledge and practical experience of the dispenser, in particular as far as safety and hygiene are concerned.
This dispenser is not a toy and shall not be used by children as such. Children shall not perform cleaning or user maintenance of this dispenser. High-risk individuals are not expected to use this dispenser safely unless continuous supervision is given.

• • Not Included
• ** For additional faceplates, contact your sales representative.

Dispenser Access

1. To unlock the dispenser, insert key into lock and rotate the key a quarter turn towards the wall. Gently pull the cover forward.
2. Support the cover while opening.

Cover Removal

Remove dispenser cover before installing the cage.
Refer to Dispenser Access section for instructions to unlock the dispenser.

1. Remove the cover by closing it about halfway. Align botto edge of cover with vertical alignment line. The key feature on the inside of the cover should line up with it’s
   corresponding slot on the dispenser body, allowing the cover to be flexed off.

2. Remove the cover.

Cage Installation

• When installing the dispenser ensure to follow all appropriate safety precautions and wear proper safety equipment including gloves.
  Note: This unit is for an install with studs on 16 inch centers or less.

• ** For push buttons and other available parts, contact your sales representative.

Tools Required

Dispenser Removal

1. These instructions are for converting an existing stainless steel folded towel dispenser with a trash can unit to a recessed hard roll towel dispensing system.

2. Locate the key and open the door to the folded towel dispenser.

3. Now open the trash can lock and remove the trash can part of the installed wall unit. Set it aside as it will be used again.

4. Determine how the system is installed in the current location. Determine where the screws are located and ensure that the system is properly secured.

5. Note that trash can system needs to be securely installed. Use 2.5 inch screws to tighten the install if needed to provide a secure install.

6. With the door closed and locked to the towel dispenser, take the pry tool and insert in between the back recessed housing and the door as shown.

7. With a hammer pound the pry tool down the side of the towel dispenser.

8. When this process is completed unlock, open the door and inspect. This process will have loosened the hinge system of the folded towel dispenser.

9. If present, remove and discard the black folded towel holder.

10. Take the housing frame to be installed and turn it over. Using the alcohol pads, clean the bottom corners and allow to air dry for 15 minutes. Then place the VHB tape on each bottom corner. Note: one or two strips will be needed. Leave the cover on the top piece of tape.

There are two methods if installation that can be used for this dispenser, the carriage bolt method and the strapping method. The Carriage Bolt Method and Strapping Method are detailed in the following sections.

Carriage Bolt Method

1. Remove door and housing if possible. Circumstances may vary based on model.

2. Take the carriage bolts and the angle brackets that came with the dispenser and determine whether the longer or the shorter one is needed for the install.

3. Carefully remove the cover on the tape on back of housing.

4. Install the dispenser housing in the area where the folded towel dispenser was located. This dispenser has a lip on top and it is important to place the lip over the top of the housing still left in the wall as shown.

5. Install the carriage bolt and angle bracket that works best for the install at the bottom of the dispenser where there are holes for the carriage bolts and angle brackets to be installed.

6. Check the level once again and ensure the system is secure.

Strapping Method

1. Find the hex head screws used to secure the folded towel system to the wall and remove them. Typically, there are 4 screws, two on the back housing at the top and two on the bottom. We have found that it is easiest to use pliers to remove the hex head screws.

2. After all the screws are removed, grasp the towel system where the folded towels would exit the dispenser and, on the door, and pull and twist until the system pops out of the housing.

3. Once the folded towel dispenser is removed, note that there is no backing where the new dispenser will be installed. If installed in an air shaft, the opening will need
   to be covered. This can be completed by cutting the box that the new dispenser came in to cover the hole or use another suitable material to cover the open area.

4. Take the type of strapping preferred and measure a piece the size of the dispenser opening. Add extra length to each side to be able to fold over the edges.

5. Use metal or plastic strapping to secure the dispenser in place. Cut the strapping with snips to the size desired fold over the edges on each side.

6. Using the 2” installation screws, screw both ends of the strapping to the bottom of the housing that is in the wall.

7. Carefully remove the cover on the tape on back of housing.

8. Install the dispenser housing in the area where the folded towel dispenser was located. This dispenser has a lip on top and it is important to place the lip over the top of the housing still left in the wall as shown.

9. Place a level in the bottom of the dispenser to ensure that the placement is level. Press sides firmly.

10. Using a carriage bolt and a 5/8 inch flat washer, tighten the dispenser to the strap.

See Module Installation Manual for next steps to install.

Do Not Flush

• Flushing of non-flushable products, such as paper towels, can cause internal plumbing issues as well as issues in municipal sewage systems.
• To help avoid such issues, Kimberly Clark Professional* provides “Do Not Flush” labels for stainless steel dispensers.
• These labels have a non-permanent adhesive and may be removed at a later date if desired.

Legal

• ®/™ Trademarks of Kimberly-Clark Worldwide, Inc. or its affiliates. © KCWW
• ®/™ Marques de commerce de Kimberly-Clark Worldwide, Inc. ou de ses filiales. © KCWW Parts made in Mexico and China, Assembled in Mexico /
• Pièces fabriquées au Mexique et en Chine, et assemblées au Mexique /
• Partes hechas en México y China, armado en México
• Distributed in the U.S. by Kimberly-Clark Global Sales, LLC, Roswell, GA 30076-2199 Distributed in Canada by Kimberly-Clark Inc., Mississauga, Ontario L5B 3Y5

References

• Restroom, Safety & Wiping Products Workplaces Trust | Kimberly-Clark Professional

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>