CENTOLIGHT X23 Moving Head Spire User Manual

August 25, 2024
CentoLight


Spire X23

230 w Discharge Beam moving head for indoor use


User Manual

Carefully read this manual and properly take care of it

Dear customer,

First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies.

We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible improvements to be introduced in the next future. Go to our website www.centolight.com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.

The CENTOLIGHT Team


1. Before you Begin

Thank you for purchasing Spire X23. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

1.1. What is included

Package include:

  • 1x CENTOLIGHT Moving head Spire X23
  • 1x 1m (40in ca.) Powercon to Europlug power cable
  • 1X 1m (40in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • 1X Safety cable
  • 2 x omega bracket
  • This User Manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

1.2. Unpacking Instructions

Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.
If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

1.3. Accessories

CENTOLIGHT can supply a wide range of quality accessories that you can use with your Spire Series equipment, like Cables, Splitters, DMX controllers, Consumables, and a wide range of other fixtures.
All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.
Ask your CENTOLIGHT dealer or check out our website www.centolight.com for any accessories you could need to ensure best performance of the product.

1.4. Disclaimer

The information and specifications contained in this User Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.

Copyright© 2021 CENTOLIGHT. All rights reserved.

2 – Safety Instructions

Read these instructions Keep these instructions Heed all warning.
Follow all instructions

2.1. Symbols Meaning

              The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.

              The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.

                 This symbol indicates a protective grounding terminal.

WARNING:    Describes precautions that should be observed to prevent the danger of injury or death to the operator.

             To protect the environment, please try to recycle packing material and exhausted consumables as much as possible.

             This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and moisture.

             Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.

3 – Mounting and Rigging

  Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

3.1. Rigging
  • the installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
  • When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation another time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.

IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

  • If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

3.2. Water / Moisture
  • The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
  • The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.
3.3. Heat
  • Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
  • The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.

Don not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -20°C to 50°C (-4°F to 122°F).

3.4. Servicing
  • Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

4 – Introduction

The Spire X23 is a stylish moving head beam in a very compact and lightweight housing. It delivers high light output and even coverage field. It features an High quality 230W Lamp. The lamp equips with the reflector built-in, providing perfect lamp alignment. The moving head features ultra sharp beam effect with low consumption. The fixture is integrated with a full complement of professional characteristics including a static gobo wheel, color wheel, 8-Facet prism, frost filter, motorized linear focus, variable speed shutter/strobe, linear dimmer, color time and gobo time controllable. The fixture supports DMX, RDM (Remote Device Management).

The fixture’s exterior housing is beautifully balanced basing on a modern design philosophy with supremely harmonious interior structure for remarkable control. The sculpted body of the Spire X23 achieves more than just a striking look. The 2*1/4 turn fastening omega clamps, available for vertical and horizontal plug-in, make installations fast and easy. It’s applicable for large scale live concerts, TV productions, road shows, clubs, etc.

4.1. Features
  • 1 x 230 w Lamp 7900°K Life span2000H

  • 2,5° Beam Angle

  • Smooth linear mechanical dimming

  • 0-20Hz high speed strobe effect with variable speed

  • 1 Color wheel with 14 dichroic colors plus
    open with half colour

  • 1 Static gobo wheel with 17 gobos plus open

  • Frost filter system (Hybrid effect for wash)

  • 8 Facet prism with variable speed and direction

  • PAN and TILT with 8/16 bit scanning, photoelectric reset and automatic error correction

  • DMX512 with RDM / Master-Slave / Auto / Sound modes

  • High Efficient low noise self adjusting fan cooling system

  • 1.8″ High resolution TFT LCD display with easy user-interface

4.2. Product Dimensions and Overview

(1) Omega Bracket
(2) Safety Clamp (not included)
(3) Safety Cable
(4) 1/4 Turn Quick-Lock Fasteners

5 – Products Description

5.1. Display Panel Description
  1. DISPLAY
  2. MENU
  3. UP
  4. ESC
  5. DOWN
  6. OK
  7. DMX
  8. ERROR

The operation panel includes the LED display and control button operation area.

5.2. Control Buttons

MENU Button – Short-press it to switch the setting pages.

UP Button – It scrolls up individual items in the selection menu and sub- menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.

DOWN Button – It scrolls down individual items in the selection menu and submenus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.

OK Button – Press ENTER to access menu levels and confirm parameter value changes.

ESC Button – Press ESC to Exit previous menu levels.

  1. 3 PIN-DMX OUT
  2. Fuse
  3. POWER IN
  4. POWER OUT
  5. 3 PIN-DMX IN
5.3. Power Input/Output Sockets

Plug the power-cord included with Spire X23 into an AC socket properly configured for this fixture. Please read “5.5. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 6 fixtures.

Power Input
100-240Vac – 50/60Hz

CENTOLIGHT X23 Moving Head Spire C - 2

  1. 1st Unit
  2. 2nd Unit
  3. 3rd Unit
  4. 4th Unit
  5. 5th Unit
  6. 6th Unit
5.4. DMX Input/Output Sockets

DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units.

5.5. About Power Connection
  • Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “9 – Features” on page 19 or rear panel of the product (AC110V-240V 50/60Hz).
  • Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
  • Never disconnect the product from power cord by pulling or tugging on the cord.
  • To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
  • Fuse holder with 6.3AM/250 V fuse (5x20mm). In case of fuse burn, to prevent the risk of fire and damaging the unit, please use only a spare of the recommended fuse type as described. Before replacing the fuse, make sure the unit turned off and dis- connected from the AC outlet.
  • Wire correspondence is as follows:

Cable (EU)

| Pin| International
---|---|---
Brown| Live|

L

Blue

| Neutral| N
Yellow/Green| Earth|

  Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

5.6. About Dmx Connection

When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling.

  1. DMX Termonator
  2. Last Unit
  3. Unit 2
  4. Unit 1
  5. DMX 512

DMX use of 3-Pin XLR Connectors

INPUT                     OUTPUT

3-Pin XLR
Pin 1: GND
Pin 2: DMX –
Pin 3: DMX +

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

5.7. DMX Terminator

DMX Terminator

  1. 120ohm, 1/4W Resistor

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX terminator, especially over long signal cable runs.

The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

Complimentary signal cable can transmits signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

5.8. 3-Pin vs 5-Pin DMX cables

DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR input fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards

  1. 3-Pin XLR (Plug)
    Pin 1: GND (Screen)
    Pin 2: Signal (-)
    Pin 3: Signal (+)

  2. 5-Pin XLR (Plug)
    Pin 1: GND (Screen)
    Pin 2: Signal (-)
    Pin 3: Signal (+)
    Pin 4: N/C
    Pin 5: N/C

  3. 3-Pin XLR (socket)
    Pin 1: GND (Screen)
    Pin 2: Signal (-)
    Pin 3: Signal (+)

  4. 5-Pin XLR (socket)
    Pin 1: GND (Screen)
    Pin 2: Signal (-)
    Pin 3: Signal (+)
    Pin 4: N/C
    Pin 5: N/C

6 – Menu Operation

By pressing MENU button, the display will cycle through 6 different menus and 32 Submenu. Press OK button to enter the corresponding menu, press UP, DOWN, LEFT or RIGHT to move in the menu and change the current parameter value. Then, press OK button again to save current value or ESC to come back.

Main Menu

| Second| Third| Fourth
---|---|---|---
Dmx Address|

000 – 512

| |

Fixture

| Dmx Mode| 16CH/20CH|
Run Mode|

DMX / Host

|

Pan Invert

| Close / Open|
Tilt Invert|

Close / Open

|

XY Sensor

| Close / Open|
Low Power Mode|

Close / Open

|

No DMX State

| Clear / Keep|
Lamp On Power|

Close / Open

|

Lamp Control

| Close / Open|
Data Recover|

Close / Open

|

Manual

| Color| 000 – 255|
Strobe|

000 – 255

|

Dimmer

| 000 – 255|
Gobo|

000 – 255

|

.
.
.
.

| .
.
.
.|
Information| Time| Current Time|

xxxxxH

Total Time

| xxxxxH
Lamp Time|

xxxxxH

Power Count

| xxxxx
Lamp Count|

xxxxx

Sensor

| Pan|

Tilt

|

.
.
.
.

|
Software Version| Panel|

Vx.xx

Motor

| Vx.xx
Factory| Password|

000 – 255

|

Pan

| 000 – 255|
Tilt|

000 – 255

|

Dimmer

| 000 – 255|
Color|

000 – 255

|

FixGobo

| 000 – 255|
.
.
.
.|

.
.
.
.

|

Reset

| XY Reset| Cancel / Run|
Motor Reset|

Cancel / Run

|

All Reset

| Cancel / Run|
Factory|

Cancel / Run

|

Display

| Language| CH / EN|
Display Flip|

OFF / ON

|

Display Mode

|

60s / Show

|

6.1. DMX 512
6.1.1. Set DMX Address

When selecting a starting DMX address, always consider the number of DMX channels. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. Spire X23 uses 16 DM X channels or 20 DM X channel (according to the DM X m ode chosen), which defines the highest configurable address from 480 -496 to have all channels controllable.
Set the Spire X23 starting address in the 001 – 496 DM X range to enable control of up to 32 products in the 16-channel control mode. Set the Spire X23 starting address in the 001 – 480 DM X range to enable control of up to 25 products in the 20-channel control mode.
To choose between 16 or 20 channel operation, press M ENU till you reach “FIXTURE ” and press ENTER; select then “DM X mode ” you then see current M ode1(16C) or Mode2(20C) mode. Press UP or DOWN to select desired value. Then press ENTER to confirm , and press M EN U to return to menu main page.
To change DM X address, press M EN U till you reach “DM X address ” and press EN TER; you then see current DMX channel. Press UP or DOWN to select desired value according to previous instructions. Then press ENTER to confirm, and press MENU to return to menu main page.

6.1.2. DMX Channel Assignments and Values

When use DMX control , the system takes 16 or 20 channels (depending on selected DM X mode. Below you can see the channel assignments for both modes.

6.1.3. Dmx Value

Show value actually in use for any channel of the projector.

6.2. Fixture

It establishes all the settings of the machine

6.2.1. DMX Mode

Choice of 16-channel or 20-channel mode

6.2.2. Run Mode

Choice of operating mode if DMX, automatic or sound.

6.2.3. Pan, Tilt, XY sensor

Choice for Pan only inversion, Tilt only or Pan with Tilt inversion.

6.2.4. Lamp – on- off

Lamp ignition management and Lam p function control.

6.3. Manual

CManual control of various internal functions, Pan, Tilt, etc. movements from 0 to 255 (Minimum + Maximum)

6.4. Information

Service information, Time for all internal timings of Lamp, Projector, total use and use since power on. Sensor for the control and functioning of all the sensors inside the lamp. software informs the version used inside by the projector

6.5. Factory

Reserved menu for the settings of all the internal functions of the projector. If necessary, contact customer assistance.

6.8. Reset

Controls all projector Reset functions, Motors and restoring functions as factory preset.

6.8. Display

Menu reserved for changing the language and reversing the display if necessary, as well as turning off the display in use after 60 seconds or never.

  1. OK

  2. Up

  3. Esc

  4. Down

  5. Menu

  6. ERR

  7. DMX

  8. LCD display

  9. DISPLAY

  10. MENU

  11. UP

  12. ESC

  13. DOWN

  14. OK

  15. DMX

  16. ERROR

7 – Channel List

Channel

| Function| Values| Description
---|---|---|---
16CH|

20CH

| | |

1

| 1|

Color Wheel

|

0

| White/open

1-5

| White+Color 1

6-9

| Color 1

10-13

| Color 1+Color 2

14-18

| Color 2

19-22

| Color 2+Color 3

23-26

| Color 3

27-30

| Color 3+Color 4

31-35

| Color 4

36-39

| Color 4+Color 5

40-43

| Color 5

44-47

| Color 5+Color 6

48-52

| Color 6

53-56

| Color 6+Color 7

57-60

| Color 7

61-64

| Color 7+Color 8

65-69

| Color 8

70-73

| Color 8+Color 9

74-77

| Color 9

78-82

| Color 9+Color 10

83-86

| Color 10

87-90

| Color 10+Color 11

91-94

| Color 11

95-99

| Color 11+Color 12

100-103

| Color 12

104-107

| Color 12+Color 13

108-111

| Color 13

112-116

| Color 13+Color 14

117-120

| Color 14

121-124

| Color 14+Color 15

125-255

| Color wheel rotation speed from slow to last

2

| 2|

Strobe

|

0-3

| Closed

4-103

| Strobe speed from slow to fast

104-107

| Open

108-207

| Pulse strobe from slow to last

208-212

| Open

213-225

| Random strobe (slow)

226-238

| Random strobe (medium)

239-251

| Random strobe (fast)

252-255

| Open

3

| 3|

Dimmer

|

0-255

| 0-100% dimmer

4

| 4|

Gobo wheel

|

0-3

| White/Open

4-7

| Gobo 1

8-11

| Gobo 2

12-15

| Gobo 3

16-19

| Gobo 4

20-23

| Gobo 5

24-27

| Gobo 6

28-31

| Gobo 7

32-35

| Gobo 8

36-39

| Gobo 9

40-43

| Gobo 10

44-47

| Gobo 11

48-51

| Gobo 12

4

| 4|

Gobo wheel

|

52-55

| Gobo 13

56-59

| Gobo 14

60-63

| Gobo 15

64-67

| Gobo 16

68-71

| Gobo 17

72-113

| Forward rotation from fast to slow

114-117

| Stop

118-159

| Backward rotation from slow to fast

160-166

| Gobo 1 shake from slow to fast

167-172

| Gobo 2 shake from slow to fast

173-179

| Gobo 3 shake from slow to fast

180-185

| Gobo 4 shake from slow to fast

186-191

| Gobo 5 shake from slow to fast

192-198

| Gobo 6 shake from slow to fast

199-204

| Gobo 7 shake from slow to fast

205-211

| Gobo 8 shake from slow to fast

212-217

| Gobo 9 shake from slow to fast

218-223

| Gobo 10 shake from slow to fast

224-230

| Gobo 11 shake from slow to fast

231-236

| Gobo 12 shake from slow to fast

237-244

| Gobo 13 shake from slow to fast

245-249

| Gobo 14 shake from slow to fast

250-255

| Gobo 15 shake from slow to fast

5

| 5| Prism1|

0-127

| Prism excluded

128-255

| Prism inserted

6

| 6| Prism rotation|

0-127

| Adjustment angle

128-190

| Forward rotation from fast to slow

191-192

| Stop

193-255

| Backward rotation from slow to fast

7

| 7| Not in use|

0-255

| Not in use

8

| 8| Frost |

0-127

| Frost excluded

128-255

| Frost inserted

9

| 9| Focus|

0-255

| In( near)to out(far)

10

| 10| Pan|

0-255

| Pan movement

11

| 11| Pan fine|

0-255

| Fine control of Pan movement

12

| 12| Tilt|

0-255

| Tilt movement

13

| 13| Tilt fine|

0-255

| Fine control of Tilt movement

14

| 14| Macro|

0-255

| Macro

15

| 15| Reset|

0-25

| Null

26-76

| Motor reset

77-127

| XY motor reset

128-255

| All motor reset

16

| 16| Lamp|

0-25

| Null

16

| 16| Lamp|

26-100

| Lamp off

101-255

| Lamp on
|

17

| X/YTime|

0-255

| Pan/Tilt speed from fast to slow
|

18

| Color Time|

0-255

| Color wheel speed from fast to slow
|

19

| Speed1|

0-255

| Prism/Frost/Strobe speed from slow to fast
|

20

| Speed2|

0-255

| Gobo speed from slow to fast

8 – Troubleshooting

Problem Probable Cause(s) Remedy
No response from fixture when power is applies No power to fixture Check

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician
No light, Lamp cuts out intermittently, or is burned out| LAMP missing or blown| Disconnect fixture and replace the Lamp
Fixture is too hot| Allow fixture to cool. If problem persists, contact service technician

Fixture resets but does not respond correctly to controller (DMX mode operation)| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller
Bad data link connection| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture**
Defective fixture on 2 devices transmitting on link| Bypass fixtures one at a time until normal operation is regained: unplug both connectors and connect them directly together

  • To contact Centolight service, see “12 – Warranty And Service” on page 21 or visit www.centolight.com
    ** For instruction on how to install a DMX terminator, see “5.7. DMX Terminator” on page 11.

9 – Features

1*High quality 230W Discharge Lamp
2000 hours rated lamp source
Electronic ballast and power supply
Smooth and precise resolution for PAN/TI LT movement
540° PAN and 270°TI LT movement optional
Scan position memory, auto reposition after unexpected movement
2.5° Beam angle
Improved optics and flat beam field
No need for adjustment of reflector or lamp
Anti – reflection 136mm front lenses
1 Static gobo wheel with 16 gobos plus open
1 Color wheel with 11 colors plus open
Variable direction rainbow effect with speed adjustable
Motorized focus from near to far
16-facet prism with variable speed and direction
Frost filter available (Hybrid effect for wash)
Dual flag mechanical dimming system
20T/sec high speed LED shutter / strobe effect with variable speed
Preset variable/ random strobe and dimming pulse effect
14/16 D M X channels USITT D M X-512
Vector mode with blackout M IB function
D M X512, master – slave and sound activated controllable or auto operation
Sound control with sensitivity adjustment
RDM available (Remote Device Management)
2.4″ TFT LCD display with 4 control buttons and battery back-up for menu preset
180° Reversible for LCD display
LCD display switch-off automatically after 60 seconds
DMX signal monitoring indicator available
Software up-datable through DMX connectors
Efficient low noise self adjusting fan cooling system
Constant temperature readout and management function
Over heat protection management

Specifications

Input Voltage:

| AC100-240V 50/60Hz
---|---

Control Signal:

| DMX512, master-slave and sound activated or auto

Control Channel:

| operation 16/20 DMX channels USITT DMX-512

Power Consumption:

| 350W

Dimensions:

| 270(D)310(W)495(H)mm

Packing Dimensions:

| 365(D)360(W)520(H)mm

Net Weight:

| 11.92kg

Gross Weight:

| 14.26kg

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.

10 – Photometric Data

PHOTOMETRICBEAM ANGLE DATA
(FC=LUX x 0.0929)

CENTOLIGHT X23 Moving Head Spire E - 2

11 – Gobos and Colors

Static gobos                                             Colors

      CENTOLIGHT X23 Moving Head Spire E - 4

12 – Warranty and Service

All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty:

  • Any accessories supplied with the product
  • Improper use
  • Fault due to wear and tear
  • Any modification of the product effected by the user or a third party

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.

While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER ­ Via Enzo Ferrari, 10 ­ 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product. For further information please visit www.centolight.com

13 – Warning

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).

Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.

For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.


www.centolight.com

MADE IN CHINA


This product is imported in EU by

FRENEXPORT SPA ­ Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy

CentoLight® is a registered trademark of FRENEXPORT SPA – Italy

www.centolight.com

Ver. 1.0 – Jul 2021

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CentoLight User Manuals

Related Manuals