ARDESTO MGL-3580D Electric Meat Grinder Instruction Manual

: June 3, 2024
: ARDESTO

Table of Contents

ARDESTO MGL-3580D Electric Meat Grinder
IMPORTANT SAFEGUARDS
IMPORTANT
DESCRIPTION
INSTRUCTION FOR USE
- ASSEMBLING
- Making sausages
HOW TO CLEAN YOUR APPLIANCES
DISPOSAL OF APPLIANCES AND BATTERIES
Warranty Conditions
WARRANTY CARD
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ARDESTO MGL-3580D Electric Meat Grinder

ARDESTO-MGL-3580D-Electric-Meat-Grinder-product

IMPORTANT SAFEGUARDS

This appliance is equipped with a thermostat system. This system will automatically cut off the power supply to the appliance in case of overheating.

If your appliance suddenly stops running:

Pull the mains plug out of the socket.
Press the switch button to turn off the appliance.
Let the appliance cool down for 60 minutes.
Put the mains plug in the socket.
Switch the appliance on again.
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and if they understand the hazards involved.
Children shall not play with the appliance.
Switch off the appliance and disconnect from the supply before changing accessories or approaching parts that move in use.

Please contact your dealer at an authorized service center if the thermostat system is activated too often. If you plug in, the indicator light will be on.

CAUTION: In order to avoid a hazardous situation, this appliance must never be connected to a time switch.

IMPORTANT

Read these instructions for use carefully and look at the illustrations before using the appliance.
Before use, tighten the fixing ring with a spanner and make sure the ring can not be detached by 4 Nm.
Keep these instructions for future reference.
Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance.
Never use any accessories or parts from other manufacturers. Your guarantee will become invalid if such accessories or parts have been used.
Do not use the appliance if the main cord, plug, or other parts are damaged.
If the main cord of this appliance is damaged, it must always be replaced by the manufacturer or a service center authorized, in order to avoid hazardous situations.
Thoroughly clean the parts that will come into contact with food before you use the appliance for the first time.
Unplug the appliance immediately after use.
Never use your finger or an object to push ingredients down the feed tube while the appliance is running. Only the pusher is to be used for this purpose.
Keep the appliance out of the reach of children.
Never let the appliance run unattended.
Switch the appliance off before detaching and installing any accessory.
Wait until the moving parts have stopped running before you remove the parts of the appliance.
Never immerse the motor unit in the water or any other liquid, nor rinse it under the tap. Use only a moist cloth to clean the motor unit.
Do not attempt to grind bones, nuts or other hard items.
Never reach into the cutter housing. Always use the pusher.
Mincers are fed with sinewless, boneless, and fatless beef that has been cut into pieces approximately 20 mm x 20 mm x 60 mm. Pushers are pressed with a force of 5N against the meat. Do not use the appliance for more than 5 minutes consecutively. Leave the appliance to cool for 10 minutes before using it again.
Accessories shall include instructions for their safe use.
It shall warn of potential injury from misuse.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
If the appliance is locked, please press the Reversal button(REV). The meat locked in cutter housing is untrodden, so the appliance can renew its usual condition.
Cleaning and user maintenance shall not be made by children Keep the appliance and its cord out of reach of children.
This appliance is intended to be used in household and similar applications such as:
- staff kitchen areas in shops, offices, and other working environments;
- farmhouses;
- by clients in hotels, motels, and other residential-type environments;
- bed and breakfast type environments.
This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.

DESCRIPTION

ARDESTO-MGL-3580D-Electric-Meat-Grinder-fig-1

Body
ON/OFF/ON/ON rotary switch
Locking handle
Tube inlet
Food pusher
Hopper plate
Head Tube
Snake
Cutting blade
Cutting plate (fine)
Cutting plate (medium)
Fixing ring
Sausage
Kebbe
Drum shredding (fine)
Drum shredding (medium)
Drum slicing
Pusher
Feeder

A warranty card is also included in the delivery set (at the end of this instruction manual). The pictures in this manual are just for reference. Please take the appearance of the actual product as the standard.

INSTRUCTION FOR USE

ASSEMBLING

Press the fastening button. Hold the head and insert it into the inlet. When inserting please pay attention to the head must adjust the appropriate direction until close to an inlet (fig.1). Then push the locking handle until the vertical position and tube (fig.2).
Place the snake into the head, long end first, and turn to feed the screw slightly until it is set into the motor housing (fig.3).
Place the cutting blade onto the snake shaft with the blade facing the front as illustrated (fig.4). If it is not fitted properly, the meat will not be ground.
Place the desired cutting plate next to the cutting blade, fitting protrusions in the slot (fig.5).
Support or press the center of the cutting plate with one finger then screw the fixing ring tight with another hand (fig.6). Do not over-tighten.
Place the hopper plate on the head and fix it into position.
Locate the unit on a firm place.
The air passage at the bottom and the side of the motor housing should be kept free and not blocked.

Mincer

Insert the worm shaft into the cutter housing, the plastic end first. Place the cutter unit onto the worm shaft. The cutting edges should be at the front. Place the medium grinding disc or coarse grinding disc (depending on the consistency you prefer) onto the worm shaft. Make sure the notch of the grinding disc fit onto the projections of the mincer head. Turn the screw ring in the direction of the arrow on the cutter housing until it is properly fastened.
Attach the cutter housing to the motor unit.
Place the tray on the upright part of the cutter housing.
Now the appliance is ready for mincing.

Cut the meat into 10cm-long, 2cm-thick strips. Remove bones, pieces of gristle and sinews as much as possible. Never use frozen meat! Put the meat in the tray. Use the pusher to gently push the meat into the cutter housing. For steak tartare, mince the meat with the medium grinding disc twice.

Making kebbe

Insert the worm shaft into the cutter housing, the plastic end first (fig.8). Place the cone in the cutter housing. Place the former on the cutter housing and screw the ring on the cutter housing (fig.9)
Attach the cutter housing to the motor unit.
Place the tray on the upright part of the cutter housing.
Now the appliance is ready for making kebbe (fig.10)

Feed the prepared kebbe mixture through the kebbe maker. Cut the continuous hollow cylinder into the desired lengths and use as required. Kebbe is a traditional Middle Eastern dish made primarily of lamp and bulgur wheat which is minced together to form a paste the mixture is extruded through the kebbe maker and cut into short lengths. The tubes can then be stuffed with a minced meat mixture, the ends pinched together, and then deep fried.

Making sausages

Mince the meat
Insert the worm shaft into the cutter housing, the plastic end first (fig.11).
Place the separator in the cutter housing.
Place the sausage horn on the cutter housing and screw the ring on the cutter housing.
Make sure the notches of the separator fit onto the projections of the mincer head.
Attach the cutter housing to the motor unit.
Place the tray on the upright part of the cutter housing.
Now the appliance is ready for making sausages.

Put the ingredients in the tray. Use the pusher to gently push the meat into the cutter housing. Put the sausage skin in lukewarm water for 10 minutes. Then slide the wet skin onto the sausage horn. Push the (seasoned) minced meat into the cutter housing. If the skin gets stuck onto the sausage horn, wet it with some water.

Making noodle

Operation time shall NOT exceed 3 minutes.
use cutting plates 10 or 11.
fill the tray with flour continuously.
mix 75g flour and 25g water to form a paste.
divide it into 2 pieces in equal size
food pushers using 5N force propulsion

SHREDDER

Press the fasten button, hold the plastic cutter housing and insert it into the tube inlet (when inserting please pay attention the plastic cutter housing must be slanted as per the arrow indicated), then move the plastic cutter housing anticlockwise until it is fastened tightly, and release the fasten button (fig.12).
Place the shredder drum into the plastic cutter housing, then move the shredder clockwise so that it being properly fastened (fig.13).
Place the pusher on the upright part of the plastic cutter housing, and use the pusher to gently push the vegetable into the plastic cutter housing (fig.14)
Now the appliance is ready for cutting.

HOW TO CLEAN YOUR APPLIANCES

Meat left behind in the cutter housing may be removed from the inside of the appliance by passing a slice of bread through the cutter housing.

Before you clean the appliance, switch the appliance off and remove the plug from the socket.
Remove the pusher and the hopper plate. Unscrew the fixing ring and remove all parts of the cutter housing (fig.15).
As shown by the arrow pulling the locking handle back to the starting position, than you can remove the head tube (fig.16).
Do not clean the parts in the dishwasher!
Wash all parts that have come into contact with meat in hot soapy water. Clean them immediately after use.
Rinse them with clear hot water and dry them immediately.
We advise you to lubricate the cutter unit and the grinding discs with some vegetable oil.

DISPOSAL OF APPLIANCES AND BATTERIES

Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country. This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing materials or other forms of utilizing old devices, you are making an important contribution to protecting our environment.

Warranty Conditions

The plant guarantees the normal operation of the product within 12 months from the date of the sale, provided that the consumer complies with the rules of operation and care provided by this Manual.

The service life of the product is 5 years
In order to avoid any misunderstanding we kindly ask you to carefully study the Owner’s Manual, and the terms of warranty, and check the correctness of filling out the Warranty Card. The Warranty Card is valid only if the following information is correctly and clearly stated: model, serial number of the product, date of sale, clear seals of the company-seller, and signature of the buyer. The model and a serial number of the product must correspond to those specified in the Warranty Card. If these terms are violated, and if the information specified in the Warranty Card is changed, erased or rewritten, the Warranty Card is considered invalid.

Setup and installation (assembly, connection, etc.) of the appliance are described in the attached documentation; they can be carried out both by the user and by specialists having the necessary qualification sent by USC or selling companies (on a paid basis). In this case, the person (the institution) installing the appliance shall be responsible for the correctness and quality of installation (setup). Please pay attention to the importance of the correct installation of the appliance, both for its reliable operation and for obtaining a warranty and free service. Require the installation specialist to enter all the necessary information about the installation in the Warranty Card.

In case of failure of the appliance during the warranty period by the fault of the manufacturer, the owner is entitled to free warranty repair upon presentation of the correctly filled Warranty Card together with the appliance in the factory configuration packed in the original packaging to the warranty workshop or the place of its purchase. Satisfaction of the customer’s claim due to the fault of the manufacturer shall be made in accordance with the law «On Protection of Consumers’ Rights». In the case of warranty repair the warranty period shall be extended for the period of repair and shipment.

WARRANTY CARD

Dear Buyer!
Congratulations on your purchase of the ARDESTO brand appliance, which was designed and manufactured in accordance with the highest quality standards, and we thank you for choosing this particular instrument.

We ask you to keep the coupon during the warranty period. When purchasing a product, require a full warranty card.

Warranty service is carried out only if there is a correctly and clearly filled original warranty card, which indicates: the product model, date of sale, serial number, warranty service period, and the seller’s seal. *
The service life of household appliances is 5 years.
The product is intended for consumer use. When using the product in commercial activities, the seller/manufacturer does not bear warranty obligations, and after-sales service is performed on a paid basis.
Warranty repair is carried out within the period specified in the warranty card for the product in an authorized service center on the conditions and terms determined by applicable law.
The product is withdrawn from the warranty in case of violation by the consumer of the operating rules set forth in the instruction manual.
The product is removed from warranty service in the following cases:
- misuse and non-consumer use;
- mechanical damage;
- damage caused by the ingress of foreign objects, substances, liquids, and insects;
- damage caused by natural disasters (rain, wind, lightning, etc.), fire, domestic factors (excessive humidity, dust, aggressive environment, etc.)
- damage caused by non-compliance of power and cable network parameters with state standards and other similar factors;
- when operating equipment in the power supply network with a missing single ground loop;
- in case of violation of seals installed on the product;
- lack of the serial number of the device, or inability to identify it.
The warranty does not cover consumables and accessories, as well as filters, shelves, drawers, stands and other containers for storing products.
The warranty period is 12 months from the date of sale.