Centolight C1018Z 8x10W RGBW 4in1 LED PAR With Motorized Zoom User Manual

Centolight C1018Z 8x10W RGBW 4in1 LED PAR With Motorized Zoom

Product Information

Specifications

• Model : Scenic C1018Z
• LED Type : 18x10W RGBW 4in1
• Zoom : Motorized
• Indoor Use Only

Product Overview
The SCENIC C1018Z is a versatile LED PAR light designed for indoor use. It features 18 high-quality RGBW 4in1 LEDs with a motorized zoom function. This allows you to adjust the beam angle according to your needs. The light is suitable for various applications such as stage lighting, events, and installations.

Features

• 18x10W RGBW 4in1 LEDs
• Motorized Zoom
• Indoor Use Only
• Compact and Lightweight Design
• Easy-to-Use Menu Operation
• DMX Control
• Master/Slave Mode
• Fan Noise & LED Temperature Control

Product Dimensions
The SCENIC C1018Z has the following dimensions

• Length : [insert length]
• Width : [insert width]
• Height : [insert height]
• Weight : [insert weight]

Product Usage Instructions

Before You Begin
Before using the SCENIC C1018Z, please take note of the following

• Read the user manual carefully.
• Ensure that all the included accessories are present.
• Follow the unpacking instructions to safely remove the product from its packaging.
• Take note of the disclaimer provided.

Safety Instructions
For your safety and the safety of others, please adhere to the following safety instructions

• Understand the meaning of the symbols used in this manual.

Mounting and Riggin
When mounting and rigging the SCENIC C1018Z, consider the following

• Ensure proper rigging to prevent accidents.
• Avoid exposing the product to water or moisture.
• Avoid exposing the product to excessive heat.
• Only allow authorized personnel to service the product.

Introduction
The SCENIC C1018Z offers the following features

• 18x10W RGBW 4in1 LEDs for vibrant color mixing.
• Motorized zoom for adjustable beam angle.

Product Setup
To set up the SCENIC C1018Z, follow these steps

1. Rear Panel Description
   Take note of the rear panel features and connectors for proper setup.

2. About Power Connection
   Ensure a secure and proper power connection for reliable operation.

3. About DMX Connection
   Connect the SCENIC C1018Z to a DMX controller for advanced control options.

4. DMX Terminator
   Use a DMX terminator for proper termination of the DMX signal.

5. 3-Pin vs 5-Pin DMX cables
   Understand the differences between 3-pin and 5-pin DMX cables and choose the appropriate one for your setup.

Menu Operation
Access and navigate through the menu options of the SCENIC C1018Z using the control panel.

1. Set DMX Address
   Assign a specific DMX address to the SCENIC C1018Z for proper control.

2. DMX Channel Assignments and Values
   Understand the DMX channel assignments and corresponding values for different control parameters.

3. Fan Noise & LED Temperature Control
   Adjust the fan noise level and monitor the LED temperature for optimal performance.

4. Master/Slave Mode
   Activate the master/slave mode for synchronized operation with multiple units.

Troubleshooting
If you encounter any issues with the SCENIC C1018Z, consult the troubleshooting section of the user manual for possible solutions.

Specifications
Refer to the specifications section of this user manual for detailed technical information about the SCENIC C1018Z.

Warranty and Service
For warranty coverage and service information, refer to the dedicated section in this user manual.

Warning
Take note of the warning section to ensure safe and proper use of the SCENIC C1018Z.

FAQ

• Q: Can the SCENIC C1018Z be used outdoors?
  A: No, the SCENIC C1018Z is designed for indoor use only.

• Q: How many DMX channels does the SCENIC C1018Z require?
  A: The SCENIC C1018Z requires [insert number] DMX channels.

• Q: Can I control multiple SCENIC C1018Z units with one DMX controller?
  A: Yes, you can control multiple SCENIC C1018Z units using the master/slave mode.

• Q: What is the warranty period for the SCENIC C1018Z?
  A: The warranty period for the SCENIC C1018Z is [insert warranty period].

Scenic C1018ZScenic C1018Z
18x10W RGBW 4in1 LED PAR with motorized zoom for indoor use.

User Manual
Carefully read this manual and properly take care of it.

Dear customer,
First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies.
We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible improvements to be introduced in the next future. Go to our website www.centolight.com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.
The CENTOLIGHT Team

BEFORE YOU BEGIN

Thank you for purchasing SCENIC C1018Z. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

1.1. What is included
Package include

• 1x CENTOLIGHT SCENIC C1018Z PAR light
• 1x 1m (40in ca.) Powercon to Europlug power cable
• 1X 2m (79in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
• This User Manual

ATTENTION : Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions
Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition.
If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.
If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories
CENTOLIGHT can supply a wide range of quality accessories that you can use with your SCENIC Series equipment, like Cables, Splitters, DMX controllers, Consumables, and a wide range of other fixtures.
All products in our catalogue has been long tested with this device, so we recom-mend you to use Genuine CENTOLIGHT Accessories and Parts.
Ask your CENTOLIGHT dealer or check out our website www.centolight.com for any accessories you could need to ensure best performance of the product.

Disclaimer
The information and specifications contained in this User Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
Copyright© 2021 CENTOLIGHT. All rights reserved.

SAFETY INSTRUCTIONS

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

Symbols Meaning

• The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
• The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.
• This symbol indicates a protective grounding terminal.
• WARNING : Describes precautions that should be observed to prevent the danger of injury or death to the operator.
• To protect the environment, please try to recycle packing material and exhausted consumables as much as possible.
• This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and moisture.
• Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.

MOUNTING AND RIGGING

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

• The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.

• When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation an-ther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.
  IMPORTANT : Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

• If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.
  CAUTION : Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

• The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
• The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat

• Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
• The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.
  Don not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -20°C to 50°C (-4°F to 122°F).

Servicing
Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal compo- nents of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

INTRODUCTION

• Scenic C1018Z is a compact and lightweight LED Par designed for live events, club installations and all those indoor applications where colored lights with variable beam are required. The projector is equipped with a motorized zoom controllable by DMX with angle between 10° and 65°. The light source features 18x10W RGBW 4in1 LEDs, designed to create bright and intense colors.
• Its main strengths are reliability and flexibility. The first is based on quality and selection of LED chips, the quality of optical lenses and the use of digital processor technology for LED chip temperature and fan speed control in order to preserve LED life and color brilliance. The second point, flexibility, means that users can choose to turn off the fan by renouncing part of luminance and make the fixture totally silent. This could be very useful to rental companies and professionals in all those “on the fly” situations, where total silence is needed (houses of worship, theaters, confer-ence halls, etc.) and do not have silent multicolor fixtures enough or simply because the installation requires more fixtures than those available.
• Scenic C1018Z is color at hand, without hassles in any venue.

Features

• High brightness / long lifespan LED chips with high-quality lens.
• RGBW 4in1 color mixing
• Flicker-free LED emission for broadcast applications
• DMX-512 control with RDM
• Motorized zoom with beam angle from 10° to 65°
• Advanced dimmer system and strobo effects
• Intelligent fan speed and control with different settings
• Lightweight aluminum housing with all-directional ventilation system

Product Dimensions and Overview

PRODUCT SETUP

Rear Panel Description

The operation panel includes the LED display and control button operation area.

1. 4 Digit LED Display
   It shows the operating mode and other system information.

2. Control Buttons
   MENU Button – Short-press it to switch the setting pages.
   UP Button – It scrolls up individual items in the selection menu and sub- menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   DOWN Button – It scrolls down individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.

3. Power Input / Output Sockets
   Plug the power-cord included with SCENIC C1018Z into an AC socket properly con-figured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 5 fixtures.

4. DMX Input / Output Sockets
   DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units.

About Power Connection

• Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “8 – Specification” on page 16 or rear panel of the product (AC110V-240V 50/60Hz).
• Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
• Wire correspondence is as follows

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection
When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling.

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION : Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

DMX Terminator

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from dis-turbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX termina-tor, especially over long signal cable runs.
The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

****Complimentary signal cable can transmits signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

3-Pin vs 5-Pin DMX cables
DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR in-put fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards

MENU OPERATION

By pressing MENU button, the display will cycle through 14 different menus. Press ENTER button to enter the corresponding menu, press UP or DOWN to modify cur-rent parameter value. Then, press ENTER button again to save current value.

DMX signal, the lower right corner indicator lights up
2| r—| Red brightness adjustment : 0-255
3| G—| Green brightness adjustment : 0-255
4| b—| Blue brightness adjustment : 0-255
5| n—| White brightness adjustment : 0-255
6| P—| Stroboscopic/speed adjustment:

• 0 = N/C
• 1-84 = lightning strobo
• 85-169 = random strobo
• 170-255 = standard stroboscopic

7| F—| Zoom adjustment : 0-255
8| Pr-(Internal Preset)|

• PR01 red PR02 green PR03 blue PR04 white
• PR05 red + green
• PR06 red + blue

|

• PR07 green + blue
• PR08 red + green + blue + white PR09 hopping
• PR10 gradient PR11 strobe
• PR12 combined effect

9| SP–| Built-in program speed setting : SP01-16
10| AU–| Auto/Audi : Auto/Sound control
11| FAN-

(*)

|

• FAN0 : Fan works only when LED temperature is above
• 40°C FAN1 : Silent mode
• FAN2 : Fan always working

12| dp–| dp0/1 : 30s instant blackout and light on
13| rEST| Reset
14| CH–| CH11/CH7 Channel Mode selection

Set DMX Address

• When selecting a starting DMX address, always consider the number of DMX channels. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. SCENIC C1018Z uses 7 DMX channels or 11 DMX channel (according to the DMX mode chosen), which defines the highest configu-rable address to 505 or 496 to have all channels controllable.
• Set the SCENIC C1018Z starting address in the 001 – 505 DMX range to enable control of up to 73 products in the 7-channel control mode. Set the SCENIC C1018Z starting address in the 001 – 496 DMX range to enable control of up to 46 products in the 11-channel control mode.
• To choose between 7 or 11 channel operation, press MENU till you reach “CH–” page and press ENTER; you then see current CH11 or CH7 current mode. Press UP or DOWN to select desired value. Then press ENTER to confirm, and press MENU to return to menu main page.
• To change DMX address, press MENU till you reach “d—” page and press ENTER; you then see current DMX channel. Press UP or DOWN to select desired value ac-cording to previous instructions. Then press ENTER to confirm, and press MENU to return to menu main page.

DMX Channel Assignments and Values
When use DMX control , the system takes 7 or 11 channels (depending on selected DMX mode. Below you can see the channel assignments for both modes.

11-ch DMX512 Channel Chart

| |
---|---|---
CHANNEL| FUNCTION| DESCRIPTION
Channel 1| Total Dimming| 0-255 : Total dimming linear dimming , from Dark to Bright.
Channel 2| Red| 0-255 : Red linear dimming, from Dark to Bright.
Channel 3| Green| 0-255 : Green linear dimming, from Dark to Bright.
Channel 4| Blue| 0-255 : Blue linear dimming, from Dark to Bright.
Channel 5| White| 0-255 : White linear dimming, from Dark to Bright.
Channel 6| Strobe|

• 0 : N/C
• 1-84 : Conventional Strobo
• 85-169 : Random Strobo
• 170-255 : Lightning Strobo

Channel 7| Color Preset|

• 0 : N/C
• 1-30 Red
• 31-61 Green
• 62-92 Blue
• 93-123 White

|

• 124-154 Red+Green
• 155-185 Red+Blue 186-
• 216 Green + Blue
• 217-255 Full Light

Channel 8| Static Mixing + Auto|

• 0-20 : N/C
• 21-38 Red
• 39-57 Green
• 58-76 Blue
• 77-95 White
• 96-114 Red+Green
• 115-133 Red+Blue

|

• 134-152 Green+Blue
• 153-171 Full Bright
• 172-190 Jump
• 191-209 Gradient
• 210-228 Strobe
• 229-255 Complete Effect

---|---|---|---
Channel 9| Auto Speed| 0-255 : Auto Speed Adjustment, from Fast to Slow
Channel 10| Zoom| 0-255 : Zoom Angle Adjustment, from Wide to Narrow
Channel 11| Reset| 0-244 : Invalid; 245-255: Reset

7-ch DMX512 Channel Chart

| |
---|---|---
CHANNEL| FUNCTION| DESCRIPTION
Channel 1| Total dimming| 0-255 : Total Linear Dimming , from Dark to Bright.
Channel 2| Red| 0-255 : Red Linear Dimming, from Dark to Bright.
Channel 3| green| 0-255 : Green Linear Dimming, from Dark to Bright.
Channel 4| blue| 0-255 : Blue Linear Dimming, from Dark to Bright.
Channel 5| white| 0-255 : White Linear Dimming, from Dark to Bright.
Channel 6| Strobe|

• 0 : N/C
• 1-84 : Conventional Strobo

|

• 85-169 : Random Strobo
• 170-255 : Lightning Strobo

Channel 7| Zoom| 0-255 : Zoom Angle Adjustment, from Wide to Narrow

Fan Noise & LED Temperature Control

• SCENIC C1018Z is equipped with a digital processor that controls fan speed and LED temperature. Users can choose among 3 operative modes from FAN0 to FAN2 as explained in “6 – Menu Operation” on page 12.
  Users can select the desired mode by pressing MENU button until they reach the “FAN-” page. Press ENTER; you see the current value. Then press UP or DOWN to choose from FAN0 to FAN2. Press ENTER to confirm and MENU to go back to the selection of menu pages.

• FAN0 keeps the fan off when LED temperature is below 40°C (104°F). It comes into operation form 41°C (105°F ca.), and the DSP increases fan speed according to LED board temperature. Heat protection limit is fixed at 90°C; in normal conditions, this limit is never exceeded, as fan would act to cool the chip. Maximum noise @ 1m
  (max. fan speed) is 43dBA ca.

• FAN1 (Silent Mode) always switches the fan off. Internal DSP controls the LED temperature and adjusts its brightness to keep the chip always cooled. Brightness reduction starts from 41°C (0% reduction) to 87°C (40% reduction ca.). Fan noise is 0dBA.

• FAN2 preset keeps the fan always working, so the LED board temperature will always be kept cooled. Fan noise @ 1m is 43dBA ca.

Master/Slave Mode
In case you need to control more SCENIC C1018Z simultaneously (all fixtures operate exactly the same way) without the use of a DMX controller, you can use the Master/Slave function. There is no specific function to be activated on the display; simply the master unit must be connected first, all the others in daisy-chain through the DMX IN-OUT connections. All units (master and slaves) should be in DMX Channel 001 only, and have same Channel Mode (all 7CH or 11CH).

TROUBLESHOOTING

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*
No light, LED cuts out intermittently, or burns out too quickly| LED missing or blown| Disconnect fixture and replace the LED
Fixture or LED is too hot| Allow fixture to cool. If problem persists, contact service technician*
Fixture resets but does not respond correctly to controller (DMX mode operation)| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller
Bad data link connection| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture
** Defective fixture on 2 devices transmitting on link| Bypass fixtures one at a time until normal operation is regained : unplug both connectors and connect them directly together

To contact CentoLight service, see “9 – Warranty And Service” on page 17 or visit www.centolight.com
For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 11.

SPECIFICATION

is stopped when LED board temperature is under 40°C; it runs when it is over)
Fan Noise| 0dB (temp under 40°C); 43.0 dBA @ 0.5m (temp. above 41°C); 6.1 dBA close to fixture
IP Rate| IP20
Working Temperature| Room Temperature between -20°C and 50°C (-4°F to 122°F)
Housing| Aluminum with fine sand wear-resistant spray paint
Operating Voltage| 110V-240V / 50-60Hz
Power Consumption| 200W max.
Fixture Size (LxD)| Min. Ø228 x 138.5 mm (Ø8.98 x 5.45 in); Max. – bracket included – Ø282 x 253 mm (Ø11.10 x 9.96 in)
Fixture Weight| 3,3 kg (7.27 lbs.)
Carton Size (LxHxD)| 290 x 290 x 290 mm (11.42 x 11.42 x 11.42 in)
Carton Weight| 4,3 kg (9.48 lbs.)

WARRANTY AND SERVICE

All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty

• Any accessories supplied with the product.
• Improper use.
• Fault due to wear and tear.
• Any modification of the product effected by the user or a third party.

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.
While under warranty, defective products may be returned to your local CENTOLI-GHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product.
For further information please visit www.centolight.com

WARNING

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

• This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law.
• This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).
• Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
• For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

References

• GHT Joint Venture
• Welcome - CentoLight

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>