Centolight PLOT 6200FZ Fresnel Light with 200W RGBALC 6in1 LED and Motorized Zoom User Manual

Centolight PLOT 6200FZ Fresnel Light with 200W RGBALC 6in1 LED and

Motorized Zoom

Product Information

The PLOT 6200FZ is a Fresnel light with a 200W RGBALC 6in1 LED and motorized zoom. It is designed and manufactured by CENTOLIGHT.

Features

• 200W RGBALC 6in1 LED
• Motorized zoom
• Fresnel lens
• DMX control
• Powercon input/output
• LED Fresnel Light with 15°-50° Motorized Zoom
• 200W RGBALC 6in1 LED with over 50,000h lifetime
• Color Temperature ranging from 2000°K up to 8500°K
• Ø130mm (5.1in) Fresnel Lens
• Zoom Range from 15° to 50°
• Up to 5630lux @ 3m
• CRI ≥90
• Smooth 16-bit Dimmer
• Flicker-Free Operation
• Low-Noise Cooling System
• Rotatable Barndoor Included

Package Contents

• 1x CENTOLIGHT PLOT 6200FZ Fresnel Light
• 1x 1.5m (59in ca.) Powercon to Europlug power cable
• 1x Powercon Connector (Grey, for mains link)
• 1x 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
• 1x User Manual

Product Usage Instructions

Before You Begin

Thank you for purchasing the PLOT 6200FZ. Before operation, carefully read this user manual.
Thank you for purchasing PLOT 6200FZ. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is Included

The package includes the following:

• 1x CENTOLIGHT PLOT 6200FZ Fresnel Light
• 1x 1.5m (59in ca.) Powercon to Europlug power cable
• 1x Powercon Connector (Grey, for mains link)
• 1x 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
• 1x User Manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Safety Instructions

Before using the PLOT 6200FZ, be sure to familiarize yourself with the safety instructions outlined in the user manual.

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

Symbols Meaning

• The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.

• The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.

• This symbol indicates a protective grounding terminal.
  WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.

• To protect the environment, please try to recycle packing material and exhausted consumables as much as possible.

• This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and moisture.

• Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.

Mounting and Rigging

Refer to section 3.1 of the user manual for instructions on rigging the PLOT 6200FZ.

• Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

• The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The  installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
• When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation anther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.
• IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.
•  If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

• The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
• The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat

• Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
• The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.
• Do not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -30÷55 °C (-22÷171 °F).

Servicing

• Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

Product Setup

Refer to section 5 of the user manual for information on power and DMX connections, as well as DMX addressing and channel assignments.

 Rear Panel Description

The operation panel includes Connectors, security eye-bolt, 4-digit LED display and control buttons.

1. Power On/Off
   It switches on and off the unit.

2. LED Display
   It shows the operating mode and all system information. Read “6 – Menu Operation” on page 12 for details on all menus.

3. Fuse Holder
   Fuse holder with F5AL/250 V fuse (5x20mm). In case of fuse burn, to prevent the risk of fire and damaging the unit, please replace only with fuse of same value.

4. Power Input/Output Sockets
   Plug the power-cord included with PLOT 6200FZ into an AC socket properly configured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 5 fixtures.

5. DMX Input/Output Sockets
   DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units. Please read “5.3. About Dmx Connection” on page 10 for details on how to man-age DMX connections.

6. Control Buttons
   MENU Button – Short-press it to switch the setting pages.
   UP Button – It scrolls up individual items in the selection menu and sub- menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   DOWN Button – It scrolls down individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.

7. Security Eye-Bolt
   In case of rigging, hook a safety cable here. This eye-bolt is intended as a second-ary safety attachment, to prevent damages in the event of fall down if the main attachment (C-Bracket) fails.

 About Power Connection

• Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “9 – Specification” on page 17 or rear panel of the product (AC110V-240V 50/60Hz).
• Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
• Wire correspondence is as follows:

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection

• When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture.
The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling. Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).
CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

DMX Terminator DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX termina-tor, especially over long signal cable runs. The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

• Complimentary signal cable can transmit signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

3-Pin vs 5-Pin DMX cables
DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR in-put fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards

Menu Operation

Refer to section 6 of the user manual for information on navigating and setting the menu options.
By pressing MENU button, the display will cycle through 11 menus. Press ENTER but-ton to enter the corresponding menu, press UP or DOWN to modify current parameter value. Then, press ENTER button again to save current value.

Press UP and DOWN keys to adjust address; press ENTER to confirm.
2| 2000-8500| CCT adjustment| Adjusts white color temperature from 2,000°K-8,500°K. Press UP and DOWN keys to change from 000 to 255; press ENTER to confirm.
3| CC00-CC99| Color Jump Function| Colors jump and change (00—99). Press “UP” or “DOWN” to choose the SPEED; press ENTER to confirm.
4| CP00-CP99| Color Fade Function| Colors gradually change (00—99). Press “UP” or “DOWN” to choose the SPEED; press ENTER to confirm.
5| R000-R255| Red Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
6| G000-G255| Green Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
7| b000-b255| Blue Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
8| L000-L255| Lime Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
9| O000-O255| Amber Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
10| C000-C255| Cyan Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
11| t000-t255| Manual Zoom| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.

Setting the DMX Address
When selecting a starting DMX address, always consider the number of DMX-512 channels. If you choose a starting address that is too high, you could restrict the access to some of the product channels. PLOT 6200FZ uses 12 DMX channels, which defines the highest configurable address, respectively, to 493 to have all channels controllable. This allows you to control of up to 42 units.

DMX Channel Assignments and Values

Below you can see the list of DMX assignments.

12-ch DMX512 Channel Chart

Bright.
CH 2| CCT| Color Temperature from 2,000°K to 8,500°K
CH 3| Dimmer Change| 000-127 = CT dimmer (white only)
128-255 = Single color dimmer (R, G, B, L, A, C)
CH 4| R Dimmer| 000-255: Red dimmer, from Dark (000) to Bright (255)
CH 5| G Dimmer| 000-255: Green dimmer, from Dark (000) to Bright (255)
CH 6| B Dimmer| 000-255: Blue dimmer, from Dark (000) to Bright (255)
CH 7| L Dimmer| 000-255: Lime dimmer, from Dark (000) to Bright (255)
CH 8| A Dimmer| 000-255: Amber dimmer, from Dark (000) to Bright (255)
CH 9| C Dimmer| 000-255: Cyan dimmer, from Dark (000) to Bright (255)
CH 10| Zoom| 000-255: Zoom adjustment
CH 11| Strobo| 000-255: Strobo speed adjustment
CH 12| Effect| 000-005: No effect;
006-040: Color Jump (motors are controlled by DMX);
041-080: Gradual Color Change (motors are controlled by DMX); 081-120: Pulse Effect (motors are controlled by DMX);
121-160: Jump effect (motors are controlled internally);
161-200: Gradual Color Change (motors are controlled internally) 201-255: Pulse Effect (motors are controlled internally);

NOTE: Under DMX condition, without a DMX controller and in daisy-chain connection of multiple Profiles (read paragraph “5.2. About Power Connection” on page 10 to see how to make), you can achieve the Master-Slave mode.  It means that the first machine of the chain controls all the other fixtures, and they follow the master one. Of course, both master and slaves must be set on same DMX address.

RDM Instructions Chart

Lux Charts

Refer to section 7 of the user manual for lux charts.

1. Lux Chart at 15° (Red only)

2. Lux Chart at 15° (Green only)
   

3. Lux Chart at 15° (Blue only)
   

4. Lux Chart at 15° (Amber only)
   

5. Lux Chart at 15° (Lime only)
   

6. Lux Chart at 15° (Cyan only)
   

7. Lux Chart at 15° (RGBALC Combined)
   

Troubleshooting

If you experience any issues with the PLOT 6200FZ, refer to section 8 of the user manual for troubleshooting steps.

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*
* No light, LED cuts out intermittently, or burns out too quickly| LED missing or blown| Disconnect fixture and replace the LED
Fixture or LED is too hot| Allow fixture to cool. If problem persists, contact service technician
Fixture resets but does not respond correctly to controller (DMX mode operation)| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller
** Bad data link connection| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture
** Defective fixture on 2 devices transmitting on link| Bypass fixtures one at a time until normal operation is regained: unplug both
connectors and connect them directly together

•  To contact CentoLight service, see “10 – Warranty And Service” on page 18 or visit www.centolight.com
• For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 11.

Warranty and Service

Refer to section 10 of the user manual for information on warranty and service.
All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/compo-nents are not covered by this warranty:

• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modification of the product effected by the user or a third party

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT. While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SER-VICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product.
For further information please visit www.centolight.com

Warning
Refer to section 11 of the user manual for important warnings and precautions.
PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

• This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE). Improper handling of this type of waste could have a possible negative impact on the environ-ment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

Dear customer,
First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies. We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible improvements to be introduced in the next future. Go to our website www.centolight.com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.

Unpacking Instructions
Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection. If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories
CENTOLIGHT can supply a wide range of quality accessories that you can use with your PLOT Series equipment, like Cables, Splitters, DMX controllers, and a wide range of other fixtures. Ask your CENTOLIGHT dealer or check out our website www. centolight.com. All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Disclaimer
The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
Copyright© 2021 CENTOLIGHT. All rights reserved.

INTRODUCTION
Centolight PLOT 6200FZ is a LED Fresnel Light with adjustable light beam from 15° and 50° via motorized zoom. The light source consists of a 200W 6-color Led (Red, Green, Blue, Amber, Lime and Cyan) whose color combination, as well as offering unmatched color palette compared to previous RGBW and RGBWA technologies, al-lows white color temperature adjustment from warm (about 2000°K) to cold (about 8500°K). The result is a Fresnel light suited to any application (theater, shows, fixed installations, etc.), also thanks to the motorized zoom controlled via DMX with 15° – 50° beam angle. The dimmer control is extremely accurate and, because of the high refresh frequency (over 15kHz), it is flicker-free and can also be used in television contexts. The quality of the Fresnel lens makes the light beam very diffused and smooth. Low noise is guaranteed by the quality of cooling fan and as well as the internal processor that allows the best balance between LED temperature and fan noise, always within 20dB @ 1m. The fixture is equipped with rotatable barndoor.

 Product Dimensions and Overview

 SPECIFICATION

• Light Source 1x200W RGBWALC 6in1 COB LED
• Zoom             Motorized from 15° to 50° (DMX or Manually Controlled)
• Chip Life       Over 50,000h
• Fresnel Lens  Ø130mm (5.1in)
• CCT (Color Temperature)   From 2000°K to 8500°K
• CRI             Ra≥90
• Flicker-Free   LED frequency over 15.000Hz
• Beam Angle    15°-50°
• Lens Material   High-Quality Glass Fresnel Lens
• Dimmer            16-Bit Smooth Linear Dimming
• Strobe effect    Yes
• Cooling System  Quite Fan (under 25dB @1m) + Copper Tube
• DMX Channel Modes  12 Channels (RDM Included)
• Control Modes   DMX, Strobo, Master-Slave, Manual Dimming
• Control Panel   4 Buttons and LED Display
• IP rate      IP20
• DMX In/Out   3-pin XLR
• Power Socket Powercon In/Out
• Voltage              100~240V 50/60Hz
• Fuse                    F5AL/250V (5x20mm)
• Max Power Consumption  220W
• Working Temperature   -30÷55 °C (-22÷171 °F)
• Barndoor                          Rotatable Barndoor (Included)
• Fixture Size (WxDxH)  400x187x220 mm – 17.75×7.36×8.66 in (only fixture, without barndoor and C-Bracket)
• Net Weight                     6,6kg – 14.55 lbs.
• Packing Size (WxDxH)  540x280x280 mm – 21.26×11.02×11.02 in
• Packing Weight              7,6kg – 16.75 lbs.

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.
This product is imported in EU by
FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy
CentoLight® is a registered trademark of FRENEXPORT SPA – Italy
www.centolight.com

References

• Welcome - CentoLight
• Welcome - CentoLight

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>