CentoLight Square 100PZ Mini LED Profile Spot 100W Power Light User Manual

CentoLight Square 100PZ Mini LED Profile Spot 100W Power Light

Product Information

Specifications

• Model: SQUARE 100PZ
• Power: 100W
• Type: Mini Led Profile Spot Light with Zoom, Beam Shaping Shutters & Gobo Slot

Product Usage Instructions

1 – Before You Begin

Thank you for purchasing SQUARE 100PZ. Please follow the instructions below before operating the equipment:

• 1.1 What is included: Check the package contents to ensure everything is included.
• 1.2 Unpacking Instructions: Follow the provided instructions for unpacking the product.
• 1.3 Accessories: Familiarize yourself with the included accessories.
• 1.4 Disclaimer: Read and understand the disclaimer before use.

2 – Safety Instructions

Prioritize safety by understanding the symbols and their meanings for safe operation.

3 – Mounting and Rigging

Properly rig and mount the equipment to ensure stability and safety during use. Avoid exposure to water, moisture, and excessive heat.

Frequently Asked Questions

• Q: How do I adjust the beam shape, zoom, and focus of the SQUARE 100PZ?
  • A: To adjust the beam shape, zoom, and focus, refer to section 6.1 in the user manual for detailed instructions.
• Q: What type of DMX cables can I use with the SQUARE 100PZ?
  • A: Refer to section 5.5 in the user manual to understand the difference between 3-pin and 5-pin DMX cables and their usage with the product.

100W Mini Led Profile Spot Light with Zoom, Beam Shaping Shutters & Gobo Slot Mini Sagomatore a Led da 100W con Zoom, Ghigliottine e Slot per Gobo

Dear customer,

First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies. We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible improvements to be introduced in the next future. Go to our website www.centolight. com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.

The CENTOLIGHT Team

Before you Begin

Thank you for purchasing SQUARE 100PZ. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included

Package includes

• 1x CENTOLIGHT SQUARE 100PZ Profile Light
• 1x Color Frame Holder
• This User Manual

ATTENTION : The packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions

Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection. If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories

CENTOLIGHT can supply a wide range of quality accessories that you can use with your SQUARE Series equipment, like Cables, Splitters, DMX controllers, and a wide range of other fixtures. In particular, there is a specific accessory specifically addressed to SQUARE 100PZ.

Ask your CENTOLIGHT dealer or check out our website www.centolight.com for any accessories you could need to ensure best performance of the product. All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Disclaimer

The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time. Copyright© 2021 CENTOLIGHT. All rights reserved

Safety Instructions

• Read these instructions
• Keep these instructions
• Heed all warning
• Follow all instructions

Symbols Meaning

Mounting and Rigging

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

• The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
• When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation anther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.

IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

If the fixture shall be lowered from the ceiling or high joists, professional trusting systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

• The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
• The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat

• Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
• The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat. Do not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -20°C to 55°C (-4°F to 131°F).

Servicing

• Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer

Introduction

Centolight SQUARE 100PZ is a professional LED Profile with adjustable beam from 15° to 30° via manual zoom and focus. It is designed for all those small and medium- sized installations where warm-white light (approx. 3,100K) is required, an adjustable light beam and the possibility of projecting gobos (e.g. shops, Showrooms, showcases, museums, auditoriums, etc.). The light source is a 100W Edison® LED with CRI ≥90 to allow excellent color rendering, especially in indoor venues. The fixture is very compact and the die-cast aluminum housing increases the heat dissipation. The cooling system uses high precision fans in order to keep noise within 25dB @ 1m.
The 4 beam-shaping shutter system allows both radial and angled adjustment of the beam. The profile is equipped with a gobo holder (optional) compartment for glass or metallic gobos, as well as the front color-frame holder (included).

Features

• LED Profile Spot with Manual Zoom from 15° to 30°
• 100W Warm White Edison® COB Led with 50,000h lifetime
• CRI: WW≥90
• Radial/Angled Blade-Framing System
• Manual Focus
• Smooth 16-bit Dimmer
• Flicker-Free Operation
• Low-Noise Cooling System
• Gobos Slot
• Color Frame Holder included

Product Dimensions and Overview

1. Color-Frame Holder Calipers
2. Zooming Adjustment Nut
3. Focusing Slot & Adjustment Nut
4. Slots for Gobos
5. Light Emitting Section
6. Handle
7. Nut for Suspension Loop
8. Beam Adjustment Flake

Product Setup

Rear Panel Description

The operation panel includes 2×8 characters LCD display and control button operation
area.

1. LED Display
   It shows the operating mode and all system information. Read “7 – Menu Operation” on page 13 for details on all menus.

2. Control Buttons

   • MENU Button – Short-press it to switch the setting pages.
   • UP Button – It scrolls up individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   • DOWN Button – It scrolls down individual items in the selection menu and submenus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
   • ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.

3. DMX Input/Output Sockets DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units. Please read “5.3. About Dmx Connection” on page 10 for details on how to manage DMX connections.

4. Power Input Socket
   Plug the power cord into an AC socket properly configured for this fixture. Please read the paragraph below for details

About Power Connection

• Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “10 – Specification” on page 16 or rear panel of the product (AC110V-240V 50/60Hz).
• Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
• Never disconnect the product from power cord by pulling or tugging on the cord.
• To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
• Wire correspondence is as follows:

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection

When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high-frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling .

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male-to-female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

DMX Terminator

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX terminator, especially over long signal cable runs. The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

Complimentary signal cable can transmit signals to 20 units at most. Signal amplifier is a must to connect more fixtures.

3-Pin vs 5-Pin DMX cables

DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR input fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards

Profile Use

Beam Shape, Zoom and Focus Adjusting

After fixing or hanging the fixture, having connected Power In and DMX In/Out cables,

1. Draw out the 4 beam-adjustment flakes (1).
2. Power on the unit and loosen the zoom (2) and focus (3) adjustment nuts.
3. Adjust the zoom first from 15° to 30°, then the focus by moving respectively on the focusing and zooming slots.

Use of Gobo

If you want to get the Gobo effect on your SQUARE 100PZ Profile, you need to purchase first the gobo-holder listed below:

Ask your CENTOLIGHT dealer or check out our website www.centolight.com for further information

You have then to make a Ø24mm (0.94”) gobo with the inverse image of the picture you want to show through the SQUARE 100PZ. Refer to the drawing beside to for all details on minimum/ maximum gobo size.

Both metal and glass can be used with SQUARE series LED Profiles.

1. Loosen the two screws for the gobo flake and then move it forward to open the slot.
2. Insert the gobo holder with the gobo inside.
3. If you need to use colors, you can use the color frame holder in front of the fixture.
4. Tum on the light and adjust Zoom and Focus knobs until your get the requested size and the clearest gobo projection.

Menu Operation

By pressing MENU button, the display will cycle through 8 menus. Press ENTER button to enter the corresponding menu, press UP or DOWN to modify current parameter value. Then, press ENTER button again to save current value.

press ENTER for confirmation
2| L000-L255| Dimmer| Press the UP and DOWN key to adjust Dimmer (001- 255), press ENTER for confirmation
3| P000-P255| Strobe speed| Press the UP and DOWN key to adjust Speed (001- 255), press ENTER for confirmation
---|---|---|---

4

|

EP-0/1

|

DMX Signal Hold

| It can be 0 or 1. When this function is 0, if you dis- connect the DMX cable, the LED will automatically turn off. When it is 1, if you disconnect the DMX cable, the LED will keep on.

Press UP and DOWN keys to choose 0 or 1, then press ENTER to confirm.

5

|

dP-0/1

|

Display Backlight

| When it is 1, the LED display will be off after about 30 seconds. When it is 0, the display will be always ON.

Press UP and DOWN keys to choose 0 or 1, then

press ENTER to confirm.

6| dISP| Display Inversion| Press UP and DOWN keys to change upside down the display; press ENTER to confirm.

7

|

t20C

|

Int. Temperature

| It shows the internal temperature. When it is over 50°C (122°F) the fan starts to run. It normally does not exceed 60° (140°F).

Setting the DMX Address

When selecting a starting DMX address, always consider the number of DMX channels. If you choose a starting address that is too high, you could restrict the access to some of the product channels. SQUARE 100PZ uses 2 DMX channels, which defines the highest configurable address to 511 to have all channels controllable. This allows you to control of up to 256 units in the 2-channel control mode.

DMX Channel Assignments and Values

When use DMX control, the system takes 2 channels. Below you can see the channel assignments.

2-ch DMX512 Channel Chart

NOTE: Under DMX condition, without a DMX controller and in daisy-chain connection of multiple Profiles (read paragraph “5.3. About Dmx Connection” on page 10 to see how to make), you can achieve the Master-Slave mode. It means that the first machine of the chain controls all the other fixtures, and they follow the master one. Of course, both master and slaves must be set on same DMX address.

Lux Chart

Troubleshooting

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*

No light, LED cuts out intermittently, or burns out too quickly

| LED missing or blown| Disconnect fixture and replace the LED

Fixture or LED is too hot

| Allow fixture to cool. If prob- lem persists, contact service technician*

Fixture resets but does not respond correctly to controller (DMX mode operation)

| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller

Bad data link connection

| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture**

Defective fixture on 2 devices transmitting on link

| Bypass fixtures one at a time until normal operation is regained: unplug both connec- tors and connect them directly together

• To contact CentoLight service, see “11 – Warranty And Service” on page 17 or visit www.centolight.com
• For instruction on how to install a DMX terminator, see “5.4. DMX Terminator”

Specification

tion
Dimmer| 16-Bit Smooth Linear Dimming
Cooling System| Quite Fan (under 25dB @1m)
DMX Channel Modes| 1 or 2-Channels (RDM Included)
Control Modes| DMX, Strobo, Master-Slave, Manual Dimming
Control Panel| 4 Buttons and LED Display
DMX In/Out| 3-pin XLR
IP rate| IP20
Mains Plug| Euro-Plug
Voltage| 100~240V 50/60Hz
Max Power Consumption| 120W
Working Temperature| -30÷55°C – -22÷131°F
Color Frame| Included
Max. Fixture Size (WxDxH)| 390x190x190mm – 15.35×7.48×7.48inch (C-bracket included)
Net Weight| 2,7kg – 5.95lbs.
Packing Size (WxDxH)| 480x240x190mm – 189.0×94.49×7.48inch
Packing Weight| 3,3kg – 7.27lbs.

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.

Warranty And Service

All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty:

• Any accessories supplied with the product
• Improper use
• Fault due to wear and tear
• Any modification of the product effected by the user or a third party

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.

While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product. For further information please visit www.centolight.com

Warning

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE). Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service

• www.centolight.com

This product is imported in EU by Questo prodotto viene importato nella UE da FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy CentoLight® is a registered trademark of FRENEXPORT SPA – Italy CentoLight® è un marchio di fabbrica registrato di FRENEXPORT SPA – Italia

References

• Welcome - CentoLight

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>