AOYUE 2981 Active Heating Soldering Station Instruction Manual

AOYUE 2981 Active Heating Soldering Station

Product Specifications

• Product Name: Aoyue 2981 Soldering Station
• Manufacturer: AOYUE INTERNATIONAL LIMITED
• Model Number: 2981
• Location: Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China
• Website: http://www.aoyue3d.com

Product Usage Instructions

Introduction
Thank you for choosing the Aoyue 2981 Soldering Station. Please read and follow the instructions in this manual for proper usage and maintenance of the equipment.

Care and Maintenance

1. Tip Temperature: Always use the lowest possible temperature when soldering to prolong tip life and prevent thermal shock to components.
2. Cleaning: Clean the soldering tip before each use to remove any residual solder or flux.
3. After Usage: Clean the tip and coat it with fresh solder after each use to prevent oxidation and extend tip life.
4. System Care: Utilize the automated sleep feature to conserve energy and prolong tip and heating element life. Power down the unit and unplug from mains if not in use for extended periods.
5. Inspecting and Cleaning the Tip: Set the temperature to the lowest level, clean the tip, check its condition, and replace if badly worn. Remove oxide with fresh solder containing flux and isopropyl alcohol.

Frequently Asked Questions (FAQ)

• Q: How should I dispose of the product?
• A: This product should not be disposed of with household waste. Please recycle responsibly through designated return and collection systems or contact the retailer for safe recycling.
• Q: What should I do before using the soldering station?
  A: Before using the unit, read the manual thoroughly for proper operation instructions. Keep the manual in an accessible place for future reference.

2981 Active Heating Soldering Station

Instruction Manual

• Thank you for purchasing the Aoyue 2981Soldering Station. Please read the manual before using the unit.
• Keep manual in accessible place for future reference.

Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

AOYUE INTERNATIONAL LIMITED
Jishui Industrial Zone, Nantou, Zhongshan City, Guangdong Province, P.R.China
http://www.aoyue3d.com

This manual is designed to familiarize and instruct the operator with the proper operation and maintenance of the equipment. The “Care and Safety Precautions” section explains the hazards of using any type of soldering or reworking device. Please read carefully and observe the guidelines in order to maximize usage and

PRODUCT DESCRIPTION

• The Aoyue 2981 a soldering iron with an active heater. It is equipped with a fast acting active heater. Designed to easily plug in to the soldering pen. The station is suitable for advance soldering needs.
• The portable and lightweight design of the system saves precious desktop space and allows easy packing for occasions where offsite soldering is required.

PACKAGE INCLUSION

• Main Station with iron and spool holder.
• With built in brass tip cleaner.
• Power supply.
• User Manual.

INSTALLATION GUIDE

INSTALLATION GUIDE

Solder spool installation:

1. Insert spool of solder into holder then place into position.
2. Take solder wire end and insert into the solder wire guide hole.

PRODUCT ASSEMBLY

• Continue threading the solder wire pass the wire guide underneath the unit.
• Pull out solder wire from front

SAFETY PRECAUTIONS

CAUTION: Improper usage can cause serious injury to personnel and/or damage to equipment and work area.  For your own  safety, please observe the following pressure

• Check each component after opening the package to make sure everything is in good condition. If there are any suspected damage, do not use the item and report the issue to your vendor.
• Turn OFF the main power switch and unplug the device from power source when moving the device.
• Do not strike or subject the main unit (and all its components) to physical shock. Use carefully to avoid damage to any part.
  • Never drop or sharply jolt the unit.
  • Contains delicate parts that may break if the unit is dropped.
• Make sure the equipment is always grounded. Always connect power to a grounded receptacle.
• Temperature may reach as high as 480°C when switched ON.
  • Do not use the device near flammable gases, paper and other flammable materials.
  • Do not touch heated parts, which can cause severe burns.
  • Do not touch metallic parts near the tip.
• Disconnect the plug from the power source if the unit will not be used for a long period.
  • Turn off power during breaks, if possible.
• Soldering process produces smoke, use on well ventilated places.
• Do not alter the unit, specifically the internal circuitry, in any manner. HIGH VOLTAGE present inside the unit. DO NOT attempt to service equipment.

SPECIFICATIONS

MAIN STATION

•  Voltage Input :  available in 110V / 220V
• Station Dimensions: 51(w) x 59 (h) x 85 (d) mm
• Weight: 235 grams
• Power Consumption: 30W
• Temperature Range: 150°C – 480°C
• Heating Element Active heater

FUNCTIONS and FEATURES

• Active heater with hot swap capability.
• Efficient active heater for fast heat recovery.
• Temperature control knob for easy adjustment.
• Portable and lightweight system.

OPERATING GUIDELINES

REMINDERS:

• Make sure the equipment is placed on a flat stable surface and all the heat-generating components placed on their respective holders or stands.
• Ensure all function switches are OFF prior plugging to wall outlet.
• Ensure all terminal connections are properly secured.

A. INITIAL PROCEDURES

1. Follow Assembly Guide to put together station.
2. Plug the DC adaptor to the unit. Then plug the DC adaptor to the wall socket.
3. Turn Power Switch ON.
4. The unit is now ready for use.

B. TEMPERATURE CONTROL

1. Turn the power ON. LED indicator will turn red indicating it is now turned on and heating.
2. To Increase the temperature, turn the Temperature control knob clock wise. To decrease Set temperature, turn the Temperature control knob counter clockwise.
3. When temperature has been reached the LED indicator will start blinking.

CARE AND MAINTENANCE

1. Tip Temperature : High temperature shortens tip life and may cause thermal shock to components. Always use the lowest possible temperature when soldering.
2. Cleaning : Always clean the soldering tip before use to  remove any residual solder or flux adhering to it.
3. After usage: Always clean the tip and coat it with fresh solder after use. This guards against oxidation and pro-longs tip life.
4. System Care: Never allow the unit to stay idle at high temperature for extended periods. Utilize the automated sleep feature to conserve energy, pro-long tip and heating element life. If unit will not be used for long periods it is advised to power down the unit and unplug from the mains.
5. Inspecting and cleaning the tip:
6. Set the temperature to lowest level.
7. When the temperature stabilizes, clean the tip and check its condition. If the tip is badly worn or deformed, replace it.
8. If the solder plated part of the tip is covered with black oxide, apply fresh solder containing flux and clean the tip again. Repeat until all the oxide is removed then coat the tip with fresh solder.
9. Never file the tip to remove oxide.
10. Remaining oxides such as the yellow discoloration on the tip can be removed with isopropyl alcohol.

References

• Aoyue Soldering Equipment & Stations | Best Soldering Iron Kits

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>