CentoLight Plot 200FZ Fresnel Light with 200W COB LED and Motorized Zoom User Manual

June 3, 2024
CentoLight

centolight-logo

CentoLight Plot 200FZ Fresnel Light with 200W COB LED and Motorized Zoom

BEFORE YOU BEGIN

Thank you for purchasing PLOT 200FZ. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included

Package include:

  • 1x CENTOLIGHT PLOT 200FZ Fresnel Light
  • 1x 1.5m (59in ca.) Power on to Europlug power cable
  • 1x Power on Connector (Grey, for mains link)
  • 1X 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • This User Manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions

Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition. If the box or the contents
(the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection. If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories

CENTOLIGHT can supply a wide range of quality accessories that you can use with your PLOT Series equipment, like Cables, Splitters, DMX controllers, and a wide range of other fixtures. Ask your CENTOLIGHT dealer or check out our website www. centolight.com. All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Disclaimer

The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
Copyright© 2021 CENTOLIGHT. All rights reserved.

SAFETY INSTRUCTIONS

  • Read these instructions
  • Keep these instructions
  • Heed all warning
  • Follow all instruction
Symbols Meaning

The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.
The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.
This symbol indicates a protective grounding terminal.
Describes precautions that should be observed to prevent the danger of injury or death to the operator.
To protect the environment, please try to recycle packing material and exhausted consumables as much as possible.
This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and moisture.
Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.

MOUNTING AND RIGGING

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging
  • The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
  • When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation anther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.

IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

  • If the fixture shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture
  • The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
  • The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.
Heat
  • Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
  • The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.

Do not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -30÷55 °C (-22÷171 °F).

Servicing
  • Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

INTRODUCTION

Centolight PLOT 200FZ is a COB LED Fresnel Light with adjustable light beam from 15° and 50° via motorized zoom. It is designed to satisfy all those applications where warm-white light (3,200K) and excellent color rendering are required, especially in indoor venues like TV studios (flicker-free operation), theaters and others.
Low noise is guaranteed by the quality of cooling fan and as well as the internal processor that allows the best balance between LED temperature and fan noise, always within 20dB @ 1m. The fixture is equipped with rotatable barndoor.

Features
  • LED Fresnel Light with 15°-50° Motorized Zoom
  • 200W Warm-White COB LED with over 50,000h lifetime
  • 3200K Color Temperature
  • Ø130mm (5.1in) Fresnel Lens
  • Zoom Range from 15° to 50°
  • 2430-832lux/5m (15°-50°) Luminous Flux
  • CRI 90
  • Smooth 16-bit Dimmer
  • Flicker-Free Operation
  • Low-Noise Cooling System
  • Rotatable Barndoor Include.

Product Dimensions and Overview

CentoLight-Plot-200FZ-Fresnel-Light-with-200W-COB-
LED-01

Product Setup

Rear Panel Description

The operation panel includes Connectors, security eye-bolt, 4-digit LED display and control buttons.

  1. Power On/Off
    It switches on and off the unit.

  2. LED Display
    It shows the operating mode and all system information. Read “6 – Menu Operation” on page 12 for details on all menus.

  3. Fuse Holder
    Fuse holder with F5AL/250 V fuse (5x20mm). In case of fuse burn, to prevent the risk of fire and damaging the unit, please replace only with fuse of same value.

  4. Power Input /Output Sockets
    Plug the power-cord included with PLOT 200FZ into an AC socket properly configured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 5 fixtures.

  5. DMX Input /Output Sockets
    DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units. Please read “5.3. About Dmx Connection” on page 10 for details on how to man-age DMX connections.

  6. Control Buttons
    MENU Button – Short-press it to switch the setting pages.
    UP Button – It scrolls up individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
    DOWN Button – It scrolls down individual items in the selection menu and sub- menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
    ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.

  7. Security Eye-Bolt
    In case of rigging, hook a safety cable here. This eye-bolt is intended as a second-ary safety attachment, to prevent damages in the event of fall down if the main attachment (C-Bracket) fails.

 About Power Connection
  • Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “9 – Specification” on page 15 or rear panel of the product (AC110V-240V 50/60Hz).
  • Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
  • Never disconnect the product from power cord by pulling or tugging on the cord.
  • To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
  • Wire correspondence is as follows:
    Cable (EU)| Pin| International
    ---|---|---
    Brown| Live| L
    Blue| Neutral| N
    Yellow/Green| Earth|

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection

When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling .CentoLight-Plot-200FZ-Fresnel-Light-with-200W-COB-
LED-03

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

DMX Terminator

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX terminator, especially over long signal cable runs.

The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

Complimentary signal cable can transmit signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

3-Pin vs 5-Pin DMX cables

DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR in-put fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standardsCentoLight-Plot-200FZ-Fresnel-Light-with-200W-COB-
LED-05

By pressing MENU button, the display will cycle through 8 menus. Press ENTER but-ton to enter the corresponding menu, press UP or DOWN to modify current parame-ter value. Then, press ENTER button again to save current value.

No. MENU Function Description
1 A001 – A512 DMX512 address set- ting (3-Ch Mode) It ranges from 1 to 512.

Press UP and DOWN keys to adjust address; press ENTER to confirm.

2

|

3CH-2CH

| DMX512 Channel Mode Selection| You can choose between 2CH and 3CH mode. Press UP and DOWN keys to adjust address; press ENTER to confirm.
3| o000 – o255| Manual Dimmer| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.
4| t000-t255| Manual Zoom| It ranges from 0 to 255. Press UP and DOWN keys to adjust address; press ENTER to confirm.

Setting the DMX Address

When selecting a starting DMX address, always consider the number of DMX channels. If you choose a starting address that is too high, you could restrict the access to some of the product channels. PLOT 200FZ uses 2 or 3 DMX channels, which defines the highest configurable address, respectively, to 511 or 508 to have all channels controllable. This allows you to control of up to 256 units in the 2-channel control mode, or 170 units in the 3-channel mode.

DMX Channel Assignments and Values

Below you can see both the 2-channel and 3-channel DMX assignments.

  1. 2-ch DMX512 Channel Chart
    | |
    ---|---|---
    CHANNEL| FUNCTION| DESCRIPTION
    Channel 1| Dimmer| 0-255: Total dimming linear dimming , from Dark to Bright.
    Channel 2| Zoom| 0-255: Zoom adjustment
  2. 3-ch DMX512 Channel Chart**
    | |
    ---|---|---
    CHANNEL| FUNCTION| DESCRIPTION**
    Channel 1| Dimmer| 0-255: Total dimming linear dimming , from Dark to Bright.
    Channel 2| Strobo| 0-255: Strobo speed adjustment
    Channel 3| Zoom| 0-255: Zoom adjustment

NOTE: Under DMX condition, without a DMX controller and in daisy-chain connection of multiple Profiles (read paragraph “5.2. About Power Connection” on page 10 to see how to make), you can achieve the Master-Slave mode.
It means that the first machine of the chain controls all the other fixtures, and they follow the master one. Of course, both master and slaves must be set on same DMX address.

LUX CHART

  1. Lux Chart at 15°
    CentoLight-Plot-200FZ-Fresnel-Light-with-200W-COB-
LED-06

  2. Lux Chart at 50°
    CentoLight-Plot-200FZ-Fresnel-Light-with-200W-COB-
LED-07

TROUBLESHOOTING

Problem Probable Cause(s) Remedy
No response from fixture when power is applied No power to fixture Check

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*


No light, LED cuts out intermittently, or burns out too quickly

| LED missing or blown| Disconnect fixture and replace the LED


Fixture or LED is too hot

| Allow fixture to cool. If problem persists, contact service technician*
Fixture resets but does not respond correctly to controller (DMX mode operation)| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller


Bad data link connection

| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture**
Defective fixture on 2 devices transmitting on link| Bypass fixtures one at a time until normal operation is regained: unplug both connectors and connect them directly together

  • To contact CentoLight service, see “10 – Warranty And Service” on page 16 or visit www.centolight.com
    ** For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 11.

SPECIFICATION

  • Light Source 1x200W Warm-White COB LED
  • Zoom Motorized from 15° to 50° (DMX or Manually Controlled)
  • Chip Life Over 50,000h
  • Fresnel Lens Ø130mm (5.1in)
  • CCT (Color Temperature) 3100±150K
  • Luminous Flux 2430 (15°) / 832 (50°) lux @ 5m, 585 (15°) / 218 (50°) lux @ 10m
  • CRI Ra≥90
  • Flicker-Free LED frequency over 15.000Hz
  • Beam Angle 15°-50°
  • Lens Material High-Quality Glass Fresnel Lens
  • Dimmer 16-Bit Smooth Linear Dimming
  • Strobe effect Yes
  • Cooling System Quite Fan (under 25dB @1m) + Copper Tube
  • DMX Channel Modes 2/3 Channels (RDM Included)
  • Control Modes DMX, Strobo, Master-Slave, Manual Dimming
  • Control Panel 4 Buttons and LED Display
  • IP rate IP20
  • DMX In/Out 3-pin XLR
  • Power Socket Powercon In/Out
  • Voltage 100~240V 50/60Hz
  • Fuse F5AL/250V (5x20mm)
  • Max Power Consumption 220W
  • Working Temperature -30÷55 °C (-22÷171 °F)
  • Barndoor Rotatable Barndoor (Included)
  • Fixture Size (WxDxH) 400x187x220 mm – 17.75×7.36×8.66 in (only fixture, without barndoor and C-Bracket)
  • Net Weight 6,6kg – 14.55 lbs.
  • Packing Size (WxDxH) 540x280x280 mm – 21.26×11.02×11.02 in
  • Packing Weight 7,6kg – 16.75 lbs.

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.

WARRANTY AND SERVICE

All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty:

  • Any accessories supplied with the product
  • Improper use
  • Fault due to wear and tear
  • Any modification of the product effected by the user or a third party

CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufac-turing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.
While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SER-VICE CENTER

  • Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy. In order to send a product to service center, you need an RMA number. Shipping charges have to be covered by the owner of the product.
    For further information please visit www.centolight.com

WARNING

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).

Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.

For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CentoLight User Manuals

Related Manuals