CentoLight SQUARE 6200P 200W RGBALC 6in1 LED Profile Spot Light User Manual

June 9, 2024
CentoLight

CentoLight-LOGO

CentoLight SQUARE 6200P 200W RGBALC 6in1 LED Profile Spot Light

Dear customer,

  • First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies.
  • We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible im-provements to be introduced in the next future. Go to our website www.centolight.com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.

BEFORE YOU BEGIN

  • Thank you for purchasing SQUARE 6200P. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included

Package includes

  • 1x CENTOLIGHT SQUARE 6200P Profile Light
  • 1x 1.5m (59in ca.) Powercon to Europlug power cable
  • 1X 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • This User Manual
  • ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions

  • Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition. If the box or the contents
    (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.

  • If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories

  • CENTOLIGHT can supply a wide range of quality accessories that you can use with your SQUARE Series equipment, like Cables, Splitters, DMX controllers, and a wide range of other fixtures. In particular, there are some specific accessories specifically addressed to SQUARE 6200P.
SKU Model Description
J706J SQUARE GOBO-200 Gobo Holder for SQUARE 150P & 6200P Profile
J768J SQUARE LENS-219 19° Lens Barrel for SQUARE 6200P Profile
J708J SQUARE IRIS-200 Manual Iris for SQUARE 150P & 6200P Profile
  • Ask your CENTOLIGHT dealer or check out our website www.centolight.com for any accessories you could need to ensure best performance of the product.
    All products in our catalogue has been long tested with this device, so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Disclaimer

  • The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
  • Copyright© 2021 CENTOLIGHT. All rights reserved.

SAFETY INSTRUCTIONS

  • Read these instructions
  • Keep these instructions
  • Heed all warning
  • Follow all instructions

Symbols Meaning

  • The symbol is used to indicate that some hazardous live termi-nals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.

  • The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.

  • This symbol indicates a protective grounding terminal.

  • WARNING: Describes precautions that should be observed to prevent the danger of injury or death to the operator.

  • To protect the environment, please try to recycle packing materi-al and exhausted consumables as much as possible.

  • This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and mois-ture.

  • Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regula-tion in your country.

MOUNTING AND RIGGING

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

  • The installation of the fixture must be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The instal-lation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.
  • When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation another time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a year.
  • IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation by yourself, in-stead use a professional structural rigger. Improper installation can result in bodily injury or property loss.
  • If the fixture shall be lowered from the ceiling or high joists, professional trussing systems must be used. The fixture must never be fixed swinging freely in the room.
  • CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

  • The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
  • The unit can not be used near water; for example near a bathtub, a kitchen sink, a swimming pool, etc.

Heat

  • Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
  • The apparatus should be located away from heat sources such as radiators, stoves or other appliances that produce heat.
  • Don not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -20°C to 55°C (-4°F to 131°F).

Servicing

  • Do not implement any servicing other than those means described in the manual. Refer all servicing to qualified service personnel only. The internal compo-nents of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

INTRODUCTION

  • Centolight SQUARE 6200P is a professional LED Profile with 26° beam (also avail-able optional 19° lens tube) designed for installations in which high LED reliability and a wide range of colors are required.
  • The light source is a 200W LED RGBALC (Red, Green, Blue, Lime, Amber, Cyan) 6in1 with CRI ≥90 and color temperature between 2000K and 8500K. The combination of these six basic colors allows a countless infinite palette, and lets you to recreate even pastel and white colors at different temperatures able to satisfy even the most demanding professionals.
  • The SQUARE 6200P is designed for indoor applications ranging from TV studios, live entertainment, theaters and museums. Great attention is paid to quality of dimmer control and chip temperature, to minimize the consequences of using LEDs instead of traditional lamps.
  • The cooling system uses high precision fans in order to keep noise within 25dB @ 1m. The 4 beam-shaping shutter system allows both radial and angled adjustment of the beam. The fixture is equipped with a compartment for gobos and manual iris (both optional), as well as the front color-frame holder (included).

Features

  • LED Profile Spot with 26° Beam (19° optional)
  • RGBALC 6in1 LED Light Source with Over 50,000h Lifetime
  • Color Temperature from 2000°K to 8500°K
  • Radial/Angled Blade-Framing System
  • Smooth 16-bit Dimmer
  • Flicker-Free Operation
  • Low-Noise Cooling System
  • Gobos/Iris Slot (optional gobo and iris)
  • Color Frame Holder (included)
Product Dimensions and Overview

CentoLight-SQUARE-6200P-200W-RGBALC-
6in1-LED-Profile-Spot-Light-FIG-3

  1. Color Frame Holder
  2. Color Flake Calipers
  3. Profile Lens Tube
  4. Focusing Slot & Adjustment Nut
  5. Focus Adjustment Tube
  6. Slot for Iris
  7. Beam Adjustment Flake
  8. Light Emitting Section
  9. Handle
  10. Nut for Suspension Loop

RODUCT SETUP

Rear Panel DescriptionCentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-
Profile-Spot-Light-FIG-5

The operation panel includes 2×8 characters LCD display and control button opera-tion area.

  1. LCD Display
    It shows the operating mode and other system information. Read “7 – Menu Opera-tion” on page 14 for details on all menus.

  2. Control Buttons

    • MENU Button – Short-press it to switch the setting pages.
    • DOWN Button – It scrolls down individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.) and increases values/settings of parameters.
    • UP Button – It scrolls up individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.) and increases values/settings of parameters.
      ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.
  3. Power Input/Output Sockets

    • Plug the power-cord included with SQUARE 6200P into an AC socket properly con-figured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 5 fix-tures.CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-6
  4. DMX Input/Output Sockets

  • DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a 3-pin female socket for sending the DMX control signal to other units.
  • Please read “5.3. About Dmx Connection” on page 11 for details on how to manage DMX connections.

About Power Connection

  • Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “10 – Specifications” on page 19 or rear panel of the product (AC110V-240V 50/60Hz).
  • Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
  • Never disconnect the product from the power cord by pulling or tugging on the cord. y To avoid electric shock, all fixtures must be connected to circuits with a suitable
    ground and circuit breaker.

Wire correspondence is as follows:

Cable (EU) Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection

  • When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).
  • DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and does not affect how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling.CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-7
  • Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Nega-tive (S-), and pin 3 is Data positive (S+).
  • CAUTION: Wires must not come into contact with each other; otherwise the fix-tures will not work at all, or will not work properly.

DMX Terminator

  • DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from dis-turbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX termina-tor, especially over long signal cable runs.

  • The DMX terminator is simply an XLR connector with a 120Ω
    (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+), respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain.

  • The connections are illustrat-ed below.

  • Complimentary signal cable can transmits signals to 20 unit fixtures at most. Signal amplifier is a must to connect more fixtures.

Pin vs 5-Pin DMX cables

  • DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards: 5-Pin XLR and 3-Pin XLR systems. If you wish to connect this fixture to a 5-Pin XLR in-put fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standardsCentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-9

PROFILE USE

Beam Shape and Focus Adjusting

  • After fixing or hanging the fixture and having connected Power In/Out and DMX In/Out cables,
  1. Draw out the 4 beam-adjustment flakes.
  2. Power on the unit and loosen the focus adjustment nuts.
  3. Move forward or back the tube to focus on the light beam.

Use of Gobo
If want to get the Gobo effect on your SQUARE 6200P Profile, you need to purchase first the gobo-holder listed below:

SKU Model Description
J706J SQUARE GOBO-200 Gobo Holder for SQUARE 150P & 6200P Profile

Ask your CENTOLIGHT dealer or check out our website www.centolight.com for further information.

  • You have then to make a Ø57mm (2.24”) gobo with the inverse image of the picture you want to show through the SQUARE 6200P.
  • Refer to the drawing beside to for all details on minimum/maximum gobo size.
  • Both metal and glass can be used with SQUARE series LED Profiles.
  1. Loosen the nut for the gobo/iris flake and then move it forward to open the slot.
  2. Insert the gobo holder with the gobo inside.
  3. Tum on the light and adjust Focus knobs until your get the clearest gobo projection.CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-12

Use of Iris

  • Sometimes it is requested to reduce the diameter of the beam even below the min-imum allowed by the lens tube (26° or 19°). In these cases you can use the SQUARE IRIS-200 iris – listed below – to reduce the diameter up to to 0°.
SKU Model Description
J708J SQUARE IRIS-200 Manual Iris for SQUARE 150P & 6200P Profile

The manual iris is installed in the same slot used for the gobos. Of course, you have to choose between iris or gobo as they cannot be used simultaneously.

  1. Loosen the nut for the gobo/iris flake and then move it forward to open the slot.
  2. Insert the iris inside the slot.
  3. Tum on the light, adjust Zoom and Focus knobs until your get the re-quested beam size.
  4. Use the manual iris to reduce the beam up to 0°.

By pressing MENU button, the display will cycle through 10 menus. Press ENTER but-ton to enter the corresponding menu, press UP or DOWN to modify current parame-ter value. Then, press ENTER button again to save current value .CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-
FIG-14 CentoLight-SQUARE-
6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-15

Setting the DMX Address

  • When selecting a starting DMX address, always consider the number of DMX chan-nels. If you choose a starting address that is too high, you could restrict the access to some of the product’s channels. SQUARE 6200P uses 11 DMX channels, which defines the highest configurable address to 495 to have all channels controllable. This allows you to control of up to 46 units.

DMX Channel Assignments and Values

  • When use DMX control , the system takes 11 channels. Below you can see the chan-nel assignments.
  1. 2-ch DMX512 Channel Chart
CH Function Description
CH1 Dimmer 000-255: Total linear dimming , from Dark to Bright.
CH2 CCT Color Temperature Adjustment (White only) from 2000K to 8500K.
CH3 Dimmer Change 000-127: CCT adjustment. 128-255: Single color dimmer.
CH4 Red 000-255: Red linear dimming , from Dark to Bright.
CH5 Green 000-255: Green linear dimming , from Dark to Bright.
CH6 Blue 000-255: Blue linear dimming , from Dark to Bright.
CH7 Lime 000-255: Lime linear dimming , from Dark to Bright.
CH8 Amber 000-255: Amber linear dimming , from Dark to Bright.
CH9 Cyan 000-255: Cyan linear dimming , from Dark to Bright.
CH10 Strobe 0-255: Lightning Strobo from slow to fast.

CH11

|

Effect

| 000-005: No effect

006-100: Color Jump Effect 101-150: Color Fade Effect 151-200: Strobe Effect

201-255: Sound Mode

NOTE: Under DMX condition, without a DMX controller and in daisy-chain connection of multiple Profiles (read paragraph “3) Power Input/Output Sockets” on page 10 to see how to make), you can achieve the Master-Slave mode. It means that the first unit of the chain controls all the others, and they follow the master. Of course, both master and slaves must be set on same DMX address.

  1. RDM Instructions Chart
N. FUNCTION DESCRIPTION
1 Feedback (address) Changeable
2 Feedback (channel) Changeable
3 Feedback (CCT) Not changeable

LUX CHARTS

  1. Lux Chart at 26° (Red only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-16
  2. Lux Chart at 26° (Green only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-17
  3. Lux Chart at 26° (Blue only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-18
  4. Lux Chart at 26° (Amber only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-19
  5. Lux Chart at 26° (Lime only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-20
  6. Lux Chart at 26° (Cyan only)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-23
  7. Lux Chart at 26° (RGBALC Combined)CentoLight-SQUARE-6200P-200W-RGBALC-6in1-LED-Profile-Spot-Light-FIG-22

TROUBLESHOOTING

Problem Probable Cause(s) Remedy
No response from fixture when power is applied No power to fixture Check

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*


No light, LED cuts out intermittently, or burns out too quickly

| LED missing or blown| Disconnect fixture and replace the LED


Fixture or LED is too hot

| Allow fixture to cool. If prob- lem persists, contact service technician*
Fixture resets but does not respond correctly to controller (DMX mode operation)| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller
Fixture resets but does not respond correctly to controller (DMX mode operation)|

Bad data link connection

| Inspect cables and correct poor connections and/or broken cables.
---|---|---
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture**


Defective fixture on 2 devices transmitting on link

| Bypass fixtures one at a time until normal operation is regained: unplug both connec- tors and connect them directly together

  • To contact CentoLight service, see “11 – Warranty And Service” on page 20 or visit www.centolight.com
  • For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 12.

SPECIFICATIONS

Light Source 1 x 200W RGBALC 6in1 LED
Chip Life Over 50,000h
Luminous Flux (26°) 2650lux @ 3m, 927lux @ 5m, 258lux @ 10m (RGBALC combined)
CRI ≥90
CCT 2,000°K to 8,500°K (White)
Refresh Rate Over 15.000Hz (Flicker-Free)
Framing System 4 Blade-Framing System with radial and angle positioning
Beam Angle 26° Lens (19° Optional)
Dimmer 16-Bit Smooth Linear Dimming
Cooling System Quite Fan (under 25dB @1m)
DMX Channel 11 Channels (RDM Included)
Control Modes DMX, Master-Slave, Manual Dimming
Display 2×8 characters LCD Display
DMX In/Out 3-pin XLR
IP rate IP33
Power Socket Powercon Input/Output
Voltage 100~240V 50/60Hz
Max Power Consumption 220W
Working Temperature -30÷55°C
Housing Surface Temp. 40°C~55°C
Max. Fixture Size (WxDxH) 700 x 327 x 360 mm – 27.5 x 12.9 x 14.2 in

(C-bracket included)
Net Weight| 9,4 kg – 20.7 lbs.
Packing Size (WxDxH)| 640 x 280 x 280 mm – 25.20 x 11.02 x 11.02 in
Packing Weight| 11,2 kg – 27.7 lbs.

WARRANTY AND SERVICE

  • All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty:
  • Any accessories supplied with the product
  • Improper use
  • Fault due to wear and tear
  • Any modification of the product effected by the user or a third party
  • CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.
  • While under warranty, defective products may be returned to your local CENTOLI-GHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto
  • Recanati – Italy. In order to send a product to service center, you need an RMA num-ber. Shipping charges have to be covered by the owner of the product. For further information please visit www.centolight.com

WARNING

  • PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only This symbol indicates that this product is not to be disposed of with your house-hold waste, according to the WEEE Directive (2012/19/UE) and your national law. This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an autho-rized collection site for recycling waste electrical and electronic equipment (WEEE).
  • Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
  • For more information about where you can drop off your waste equipment for recy-cling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.
  • www.centolight.com
  • This product is imported in EU by
  • Questo prodotto viene importato nella UE da
  • FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy
  • CentoLight® is a registered trademark of FRENEXPORT SPA – Italy CentoLight® è un marchio di fabbrica registrato di FRENEXPORT SPA – Italia
  • www.centolight.com

Documents / Resources

| CentoLight SQUARE 6200P 200W RGBALC 6in1 LED Profile Spot Light [pdf] User Manual
SQUARE 6200P, SQUARE 6200P 200W RGBALC 6in1 LED Profile Spot Light, 200W RGBALC 6in1 LED Profile Spot Light, RGBALC 6in1 LED Profile Spot Light, 6in1 LED Profile Spot Light, LED Profile Spot Light, Profile Spot Light, Spot Light
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CentoLight User Manuals

Related Manuals