Centolight Scenic COB-200W 200W Warm-Cold White COB Led Par Light User Manual

June 12, 2024
CentoLight

Centolight Scenic COB-200W 200W Warm-Cold White COB Led Par Light

Product Information

Product Name: SCENIC COB-200W

Product Description: 200W Warm-Cold White COB Led Par Light

Product Contents:

  • 1x CENTOLIGHT SCENIC COB-200W Par Light
  • 1x 1.2m (47in ca.) Powercon to Europlug power cable
  • 1x 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • User Manual

Product Usage Instructions

Before operating the SCENIC COB-200W, please read the following instructions carefully:

Before you Begin
Thank you for purchasing SCENIC COB-200W. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included
The package includes the following items:

  • 1x CENTOLIGHT SCENIC COB-200W Par Light
  • 1x 1.2m (47in ca.) Powercon to Europlug power cable
  • 1x 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • User Manual

Safety Instructions
The safety instructions provide important information for the proper and safe usage of the product. Please refer to the user manual for detailed safety instructions.

Mounting and Rigging
The mounting and rigging instructions provide guidance on how to safely install and secure the product. Please refer to the user manual for detailed mounting and rigging instructions.

Introduction
The introduction section provides an overview of the product features and dimensions. Please refer to the user manual for detailed information.

Product Setup
The product setup instructions explain the rear panel description, power connection, DMX connection, DMX terminator, and the difference between 3-Pin and 5-Pin DMX cables. Please refer to the user manual for detailed setup instructions.

Menu Operation
The menu operation section explains how to set the DMX address,DMX channel assignments, and values. Please refer to the user manual for detailed menu operation instructions.

Lux Charts
The lux charts provide information on the light output of the product at different distances. Please refer to the user manual for detailed lux charts.

Troubleshooting
The troubleshooting section provides solutions to common issues that may occur during usage. Please refer to the user manual for detailed troubleshooting instructions.

Specification
The specification section provides technical details about the product. Please refer to the user manual for detailed specifications.

Warranty And Service
The warranty and service information explain the terms and conditions of the product warranty and service. Please refer to the user manual for detailed warranty and service information.

Warning
The warning section provides important safety warnings and precautions. Please read and follow these warnings to ensure safe usage of the product. Please refer to the user manual for detailed warnings.

Dear customer,
First of all thanks for purchasing a CENTOLIGHT® product. Our mission is to satisfy all possible needs of light designers and professionals of entertainment lighting, by offering a wide range of products based on the latest technologies.
We hope you will be satisfied with this fixture and, if you want to collaborate, we are looking for a feedback from you about product operation and possible improvements to be introduced in the next future. Go to our website www.centolight.com and send an e-mail with your opinion; this will help us to build equipment ever closer to professional’s real requirements.

Before you Begin

Thank you for purchasing SCENIC COB-200W. Enjoy your new equipment and make sure to read this manual carefully before operation! This user manual is made to provide both an overview of controls, as well as information on how to use them.

What is included

Package include:

  • 1x CENTOLIGHT SCENIC COB-200W Par Light
  • 1x 1.2m (47in ca.) Powercon to Europlug power cable
  • 1X 1.5m (59in ca.) DMX Cable 3-pin XLR-M to 3-pin XLR-F
  • This User Manual

ATTENTION: Packaging bag is not a toy! Keep out of reach of children!!! Keep in a safe place the original packaging material for future use.

Unpacking Instructions

Carefully unpack the product immediately and check the content to make sure all the parts are in the package and are in good condition. If the box or the contents (the product and included accessories) appear damaged from shipping, or show signs of mishandling, notify the carrier or dealer/seller immediately. In addition, keep the box and contents for inspection.
If the fixture must be returned to the manufacturer, it is important that it is returned in the original manufacturer box and packing. Please do not take any action without first contacting your dealer or getting in touch with our after-sales support service (visit www.centolight.com for details).

Accessories

CENTOLIGHT can supply a wide range of quality accessories that you can use with your SCENIC Series equipment, like Cables, Splitters, DMX controllers, and a wide range of other fixtures. Ask your CENTOLIGHT dealer or check out our website www.centolight.com. All products in our catalogue has been long tested with this device,so we recommend you to use Genuine CENTOLIGHT Accessories and Parts.

Disclaimer
The information and specifications contained in this Manual are subject to change without notice. CENTOLIGHT assumes no responsibility or liability for any errors or omissions and reserves the right to revise or to create this manual at any time.
Copyright© 2021 CENTOLIGHT. All rights reserved.

Safety Instructions

  • Read these instructions
  • Keep these instructions
  • Heed all warning
  • Follow all instructions

Symbols Meaning

The symbol is used to indicate that some hazardous live terminals are involved within this apparatus, even under the normal operating conditions, which may be sufficient to constitute the risk of electric shock or death.

The symbol is used to describe important installation or configuration problems. Not following advice and information on how to avoid such problems may lead to product malfunction.

This symbol indicates a protective grounding terminal.

WARNING:
Describes precautions that should be observed to prevent the danger of injury or death to the operator.

To protect the environment, please try to recycle packing material and exhausted consumables as much as possible.

This symbol indicates that the fixture is intended to indoor use only. Keep the machine dry and do not expose to rain and moisture.

Don’t throw this product away just as general trash, please deal with the product follow the abandon electronic product regulation in your country.

Mounting and Rigging

Pay attention to safety! Please respectively consider the EN 60598-2-17 and the national standard during the installation. Only authorized technicians can carry out the installation.

Rigging

  • The installation of the fixture has to be built and constructed in a way that it can hold 10 times the weight for 1 hour without any harming demolition. The installation must always be secured with a secondary safety attachment, e.g. an appropriate catch net. This secondary safety attachment must be constructed in a way that no part of the installation can fall down if the main attachment fails.

  • When rigging, de-rigging or servicing the fixture staying in the area below the installation place, on bridges, under high working places and other endangered areas is forbidden. The operator has to make sure that the safety measure and the machine’s technical installation is approved by an expert before taking into operation for the first time and after changes before taking into operation anther time. He has also to make sure that an expert approves safety measure and the machine’s technical installation once a years.
    IMPORTANT: Overhead rigging requires extensive experience, including (but not limited to) calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the projector. If you lack these qualifications, do not attempt the installation yourself, but instead use a professional structural rigger. Improper installation can result in bodily injury or property loss.

  • If the fixture shall be lowered from the ceiling or high joists, professional trusting systems have to be used. The fixture must never be fixed swinging freely in the room.

CAUTION: Use appropriate clamps to rig the fixture on the truss. Make sure that the device is fixed properly! Ensure that the structure (truss) to which you are attaching the fixtures is secure.

Water / Moisture

  • The product is for indoor use. In order to prevent risk of fire or electric shock, do not expose to rain or moisture
  • The unit can not be used near water; for example near a bathtub, a kitchen sink,a swimming pool, etc.

Heat

  • Do not use in a confined space. Always install the product in a location with adequate ventilation, at least 20in (50 cm) from adjacent surfaces. Be sure that no ventilation slots on the product’s housing are blocked.
  • The apparatus should be located away from heat sources such as radiators,stoves or other appliances that produce heat.

Do not use it when maximum ambient temperature is higher than 50°C. Work temperature ranges from -30°C to 55°C (-22°F to 131°F).

Servicing

  • Do not implement any servicing other than those means described in the manual.
    Refer all servicing to qualified service personnel only. The internal components of the equipment must be purchased from the manufacturer. Only use accessories/attachments or parts recommended by the manufacturer.

Introduction

Centolight Scenic COB-200W is a 200W COB Led Par with 60° beam angle. The light source combines Warm-White at 3200K and Cold-White at 6500K, both controllable separately in manual or DMX mode. It is designed for all those applications that could need variable white color temperature, as live shows, discos, showrooms, etc.
The silence is guaranteed by the quality of cooling fan controlled by the internal processor, which maintains the overall noise within 20dB @ 1m. The structure of the light is in die-cast aluminum, for maximum lightness and robustness. The fixture is also equipped with bran-door.

Features
  • COB Led Par Light with 60° Beam Angle
  • 200W COB LED with over 50,000h lifetime
  • Color Temperature: 3200K + 6400K
  • Luminous Flux: 888lux @ 3m, 347lux @ 5m
  • CRI: Ra≥90
  • Smooth 16-bit Dimmer
  • Flicker-Free Operation
  • Low-Noise Cooling System
  • Barndoor Included
Product Dimensions

Product Setup

Rear Panel Description

Centolight-Scenic-COB-200W-200W-Warm-Cold-White-COB-Led-Par-
Light-4

The operation panel includes 2×8 characters LCD display and control button operation area.

  1. LED Display
    It shows the operating mode and all system information. Read “6 – Menu Operation” on page 12 for details on all menus.

  2. Control Buttons
    MENU Button – Short-press it to switch the setting pages.
    UP Button – It scrolls up individual items in the selection menu and sub-menus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
    DOWN Button – It scrolls down individual items in the selection menu and submenus for system settings (DMX address, Operation Mode, etc.), and increases values/settings of parameters.
    ENTER Button – Press ENTER to access menu levels and confirm parameter value changes.

  3. Power Input/Output Sockets
    Plug the power-cord included with SCENIC COB-200W into an AC socket properly configured for this fixture. Please read “5.2. About Power Connection” on page 10 for details. This fixture is also equipped with an output power connector to be used as power mains source in case of cascade connection up to a maximum of 5 fixtures.
    Power Input
    100-240Vac – 50/60HzCentolight-Scenic-COB-200W-200W-Warm-Cold-White-COB-
Led-Par-Light-5

  4. DMX Input/Output Sockets
    DMX Input is a 3-pin male XLR socket for connection to a DMX control device. DMX output is a3-pin female socket for sending the DMX control signal to other units.
    Please read “5.3. About Dmx Connection” on page 10 for details on how to manage DMX connections.

About Power Connection
  • Always make sure that the voltage of the outlet you are connecting the product to is within the range stated in paragraph “9 – Specification” on page 16 or rear panel of the product (AC110V-240V 50/60Hz).
  • Make sure the power cord is not crimped or damaged. Never connect this product to a dimmer pack or rheostat.
  • Never disconnect the product from power cord by pulling or tugging on the cord.
  • To avoid electric shock, all fixtures must be connected to circuits with a suitable ground and circuit breaker.
  • Wire correspondence is as follows:
Cable (EU) Pin International
Brown Live L
Blue Neutral N
Yellow/Green Earth

Earth must be connected! Always pay attention to safety! Before taking into operation for the first time, the installation has to be approved by an expert.

About Dmx Connection
When use a DMX controller, please make sure that there is no interference sources (e.g. intercom, high frequency radio waves and radiation source).

DMX machines are designed to receive data through a serial Daisy Chain. A Daisy Chain connection is where the DATA OUT of one fixture connects to the DATA IN of the next fixture. The order in which the machines are connected is not important and has no effect on how a controller communicates to each of them. Use an order that provides for the easiest and most direct cabling.

Centolight-Scenic-COB-200W-200W-Warm-Cold-White-COB-Led-Par-
Light-6

Connect machines using shielded 2-conductor twisted pair cable with 3-pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-), and pin 3 is Data positive (S+).

CAUTION: Wires must not come into contact with each other; otherwise the fixtures will not work at all, or will not work properly.

DMX Terminator

DMX is a resilient communication protocol, however errors still occasionally occur. In order to prevent electrical noise from disturbing and corrupting the DMX control signals, a good habit is to connect DMX output of last fixture in the chain to a DMX terminator, especially over long signal cable runs.

The DMX terminator is simply an XLR connector with a 120Ω (ohm), 1/4 Watt resistor connected across Signal (-) and Signal (+),respectively, pins 2 and 3, which is then plugged into the output socket on last projector in the chain. The connections are illustrated below.

Complimentary signal cable can transmit signals to 20-unit fixtures at most.
Signal amplifier is a must to connect more fixtures.

3-Pin vs 5-Pin DMX cables
DMX connection protocols used by controllers and fixtures manufacturers are not standardized around the world. However, two are the most common standards:
5-Pin XLR and 3-Pin XLR system. If you wish to connect this fixture to a 5-Pin XLR input fixture, you need to use an adapter-cable or make it by yourself. Below you can see the wiring correspondence between 3-Pin and 5-Pin plug and socket standards.

Centolight-Scenic-COB-200W-200W-Warm-Cold-White-COB-Led-Par-
Light-8

By pressing MENU button, the display will cycle through 11 menus. Press ENTER button to enter the corresponding menu, press UP or DOWN to modify current parameter value. Then, press ENTER button again to save current value.

No. MENU Function Description
1 H001 – H512 DMX512 address setting (6CH Mode) It ranges from 1 to 512.

Press UP and DOWN keys to adjust address; press ENTER to confirm.
2| A001 – A512| DMX512 address setting (4CH Mode)| It ranges from 1 to 255. Press UP and DOWN keys to adjust brightness; press ENTER to confirm.
3| d001 – d512| DMX512 address setting (2CH Mode)| It ranges from 1 to 512. Press UP and DOWN keys to adjust address; press ENTER to confirm.

4

|

CL01-CL03

| White Color Com- bination (100% dimmer)| CL01=Warm White; CL02= Cool White; CL03=W- W+CW

5

|

CC00-CC15

| WW – CW – WW+CW

alternate Jump Effects

| It ranges from 00 to 15 with different jump speed. Press UP and DOWN keys to choose preset; press ENTER to confirm.

6

|

dE00-dE15

| WW – CW – WW+CW

alternate Fade Effects

| It ranges from 00 to 15 with different fade speed. Press UP and DOWN keys to choose preset; press ENTER to confirm.

7

|

CP00-CP15

| WW – CW – WW+CW

alternate Jump/Fade Effects

| It ranges from 00 to 15 with different jump/fade speed. Press UP and DOWN keys to choose pre- set; press ENTER to confirm.

8

|

u000 – u255

| WW brightness man- ual control| It ranges from 0 to 255. Press UP and DOWN keys to adjust brightness; press ENTER to con- firm.

9

|

C000 – C255

| CW brightness manu- al control| It ranges from 0 to 255. Press UP and DOWN keys to adjust brightness; press ENTER to con- firm.

10

|

F000 – F255

| Strobe Speed manual control| It ranges from 1Hz to 20Hz. Values range from 0 to 255. Press UP and DOWN keys to adjust speed, then press ENTER to confirm.

11

|

SoUd

|

Sound Mode

| It activates sound mode. The fixture changes between CW, WW and CW+WW modes accord- ing to sound level.

Setting the DMX Address
When selecting a starting DMX address, always consider the number of DMX channels.
If you choose a starting address that is too high, you could restrict the access to some of the product channels. SCENIC COB-200W uses 6, 4 and 2 DMX channel modes, which defines the highest configurable address, respectively, to 505, 509 and 511 to have all channels controllable. This allows you to control of up to 84 units in the 6-ch, 128 units in the 4-ch, and 256 units in the 2-channel mode.

DMX Channel Assignments and Values
When use DMX control, the system can take 2, 4 or 6 channels. Below you can see the channel assignments for each mode.

6 Channel Chart (H001-H512)

CHANNEL FUNCTION DESCRIPTION
Channel 1 Global Dimmer 0-255: Warm/Cool White dimming, from Dark to Bright.
Channel 2 Warm-White Dimmer 0-255: Warm White dimming, from Dark to Bright.
Channel 3 Cool-White Dimmer 0-255: Cool White dimming, from Dark to Bright.
Channel 4 WW+CW Strobe 0-255: Strobo speed adjustment

Channel 5

|

Effects

| 0-50: Blank

51-100: Jump change;

101-150: Gradual change;

151-200: Pulse change;

201-255: Sound

Channel 6| Effect Speed| 0-255: Speed 0% – 100%

4 Channel Chart (A001-A512)

CHANNEL FUNCTION DESCRIPTION
Channel 1 Global Dimmer 0-255: Warm/Cool White dimming, from Dark to Bright.
Channel 2 Warm-White Dimmer 0-255: Warm White dimming, from Dark to Bright.
Channel 3 Cool-White Dimmer 0-255: Cool White dimming, from Dark to Bright.
Channel 4 WW+CW Strobe 0-255: Strobo speed adjustment

2 Channel Chart (d001-d512)

CHANNEL FUNCTION DESCRIPTION
Channel 1 Warm-White Dimmer 0-255: Warm White dimming, from Dark to Bright.
Channel 2 Cool-White Dimmer 0-255: Cool White dimming, from Dark to Bright.

NOTE: Under DMX condition, without a DMX controller and in daisy-chain connection of multiple units (read paragraph “5.2. About Power Connection” on page 10 to see how to make), you can achieve the Master-Slave mode. It means that the first machine of the chain controls all the other fixtures, and they follow the master one. Of course, both master and slaves must be set on same DMX address.

Lux Charts

Centolight-Scenic-COB-200W-200W-Warm-Cold-White-COB-Led-Par-
Light-9 Centolight-Scenic-
COB-200W-200W-Warm-Cold-White-COB-Led-Par-Light-10

Troubleshooting

Problem Probable Cause(s) Remedy
No response from fixture when power is applied No power to fixture Check

power cables
Check mains plug
Fixture does not reset correctly| Electronic failure| Contact service technician*


No light, LED cuts out intermittently, or burns out too quickly

| LED missing or blown| Disconnect fixture and replace the LED


Fixture or LED is too hot

| Allow fixture to cool. If prob- lem persists, contact service technician*






Fixture resets but does not respond correctly to controller (DMX mode operation)

| Controller not connected| Connect controller
Incorrect addressing of the fixtures| Check address setting on fixture and controller


Bad data link connection

| Inspect cables and correct poor connections and/or broken cables.
Conflict between tracking and vector control| Eliminate scene cross-fade on controller
Data link not terminated| Insert termination plug in output of last fixture**


Defective fixture on 2 devices transmitting on link

| Bypass fixtures one at a time until normal operation is regained: unplug both connec- tors and connect them directly together

To contact CentoLight service, see “10 – Warranty And Service” on page 17 or visit www.centolight.com
For instruction on how to install a DMX terminator, see “5.4. DMX Terminator” on page 11.

Specification

Light Source 200W Warm-Cool White COB LED (100W+100W)
Chip Life over 50,000h
CCT (Color Temperature) 3200K + 6400K
Luminous Flux (3200K+6400K 2in1) 888lux @ 3m, 347lux @ 5m, 104lux @ 10m
CRI Ra≥90
Dimmer Control Freq. over 15kHz (Flicker-Free)
Beam Angle 60°
Dimmer 16-Bit Smooth Linear Dimming
Strobe effect Yes
Cooling System Quite Fan (under 25dB @1m)
DMX Channel Modes 2/4/6 Channels (RDM Included)
Control Modes DMX, Master-Slave, Sound, Auto Run, Manual Dimming
Control Panel 4 Buttons and LED Display
IP Rate IP22
DMX In/Out 3-pin XLR
Power Socket Powercon In/Out
Voltage: 100~240V 50/60Hz
Max Power Consump- tion 230W
Working Temperature -30÷55°C
Barndoor Included
Fixture Size (WxDxH) 234x313x290mm – 9.21×12.32×11.42in (C-Bracket and

barndoor not included)
Net Weight| 4kg – 8.81 lbs.
Packing Size (WxDxH)| 250x250x370mm – 9.84×9.84×14.57in
Packing Weight| 4,6kg – 10.14 lbs.

Note: Our products are subject to a process of continual further development. Therefore modifications to the technical features remain subject to change without further notice.

Warranty And Service

All CENTOLIGHT products feature a limited two-year warranty. This two-year warranty starts from the date of purchase, as shown on your purchase receipt. The following cases/components are not covered by this warranty:
Any accessories supplied with the product

  • Improper use
  • Fault due to wear and tear
  • Any modification of the product effected by the user or a third party CENTOLIGHT shall satisfy the warranty obligations by remedying any material or manufacturing faults free of charge at CENTOLIGHT’s discretion either by repairing or exchanging individual parts or the entire appliance. Any defective parts removed from a product during the course of a warranty claim shall become the property of CENTOLIGHT.

While under warranty, defective products may be returned to your local CENTOLIGHT dealer together with the original proof of purchase. To avoid any damages in transit, please use the original packaging if available. Alternatively, you can send the product to CENTOLIGHT SERVICE CENTER – Via Enzo Ferrari, 10 – 62017 Porto
Recanati – Italy. In order to send a product to service center, you need an RMA number.
Shipping charges have to be covered by the owner of the product.
For further information please visit www.centolight.com

Warning

PLEASE READ CAREFULLY – EU and EEA (Norway, Iceland and Liechtenstein) only

This symbol indicates that this product is not to be disposed of with your household waste, according to the WEEE Directive (2012/19/UE) and your national law.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and electronic equipment (WEEE).
Improper handling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effective usage of natural resources.
For more information about where you can drop off your waste equipment for recycling, please contact your local city office, waste authority, approved WEEE scheme or your household waste disposal service.

www.centolight.com

This product is imported in EU by
Questo prodotto viene importato nella UE da
FRENEXPORT SPA – Via Enzo Ferrari, 10 – 62017 Porto Recanati – Italy

CentoLight® is a registered trademark of FRENEXPORT SPA – Italy

www.centolight.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CentoLight User Manuals

Related Manuals