KSE-LIGHTS KS-6003 Cap Lamp Instruction Manual

: June 1, 2024
: KSE-LIGHTS

Table of Contents

KSE-LIGHTS KS-6003 Cap Lamp
Product Information
Product Overview
Features
FIRST USE
SAFETY INFORMATION
Contact
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KSE-LIGHTS KS-6003 Cap Lamp

Product Information

Specifications

Model: 6003 Series
Product Models: KS-6003 & KS-6003-DUO
Lumens: 20/45/70 lumens
Light Modes: #1, #2, #3
Beam Distance: 15/30/55 meters
Waterproof Rating: IP68
Battery Life: 30/45/10 hours
Boost Mode: 420 lumens

FAQ

Q: Can I use any charger to charge the cap lamp?
- A: No, only use original KSE-LIGHTS chargers to avoid negative effects on the product’s lifespan.
Q: What should I do if the charge status LED does not turn red when charging?
- A: Check the connection between the cap-lamp and charging cable, ensuring it is properly inserted and not under tension. If the issue persists, contact KSE-LIGHTS customer support.

Product Overview

KSE-LIGHTS-KS-6003-Cap-Lamp-fig-1

SIGNAL LIGHT

The signal light is switched on by pressing the button for a longer time (~3sec.).
Further pressing will cycle through the available light colors. Another long press switches the main light on again.
The boost mode switches on by pressing the button for ~5sec. After 30 seconds, the light reverts back.

Features

6003-PERFORMANCE
KS-6003

20/45/70 lumens
15/30/55 meters
30/45/10 hours
420 lumens BOOST MODE
light mode #1
- light mode #2
- light mode #3
IP68
<3 hours charging
3 colour signal light

6003-POWER
KS-6003-DUO

70/130/260 lumens
55/100/200 meters
10/5/2,5 hours
420 lumens BOOST MODE
light mode #1
- light mode #2
- light mode #3
IP68
<3 hours charging
3 colour signal light

FIRST USE

The cap lamp must be fully charged before first use. To do this, connect the charger to a suitable power source and plug the charger into the charging port on the light.
Now a red charging status LED in the lamp will light up constantly. This diode signals an active charging process. As soon as the charging process is completed, the red LED goes out and a green LED lights up constantly.
The lamp is now fully charged.Please read the safety regulations regarding charging.
After the lamp has been fully charged, the lamp can be switched on using the on/off switch.
By pressing the switch several times, the individual modes are switched through as described. After the last mode, the lamp switches off.
The lamp has a display that indicates the current battery level. The display is always activated for 15 seconds after the lamp is switched off. The battery status is divided into 3 levels: green=> 70% orange= >30 to 70% red= <30
To determine the battery status as accurately as possible, leave the light on for at least 10 seconds.
The lamp may be used and recharged at any time without negatively affecting the battery.
If the lamp is connected to the charger when it is switched on, the emergency light function is activated.When the charging process starts, the light goes out. If the mains voltage is now disconnected, the light switches on automatically and thus ensures an illuminated environment during the emergency situation.
The lamp is resistant to oil, grease, glue, hydrocarbon, turpentine substitute and various cleaning agents.
Wash the lamp body and the windscreen with lukewarm soapy water. Do not use acid or abrasive cleaners, especially not on the windscreen.
Do not use a high-pressure hose!
Technical maintenance or repair may only be carried out by KSE-LIGHTS or an authorised person.
KSE-LIGHTS gives a two-year warranty on the product for material and manufacturing defects. Excluded from the guarantee are normal wear and tear, oxidation, changes, improper use, storage and maintenance as well as damage caused by negligence or use for which the product is not intended.
The warranty on the accumulator is limited to one year. If the serial number is removed, the warranty is immediately void. Customer service in the event of a warranty claim, please return the lamp to the dealer with proof of purchase. It will be repaired or replaced.
Do not open the lamp or charger under any circumstances. Do not use or recharge the lamp if it is defective. No warranty claims can be made for consequential damage caused by defective parts. Failure to do so will invalidate the warranty and the operational safety.
KSE-LIGHTS accepts no liability for direct, indirect and accidental consequences, as well as any other form of damage due to the use of this product.

FIRST USE

connect the cap-lamp with the charging cable as shown in the figure. The charge status LED in the light will turn red. As soon as the status LED of the charger lights green, the cap lamp is fully charged.
Make sure that the cable is not under tension and is fully inserted into the cap-lamp.
the cap-lamp can be charged and recharged at any time.

KS-5300

AC 110 – 230V , 50/60Hz incl. EU/UK/AU/US

SAFETY INFORMATION

(cap lamp)

Do not use damaged lamps, chargers, or sockets, to charge the lamp.
Do not pull on the power cord to remove the AC adapter.
Use only original KSE-LIGHTS chargers. The use of other chargers can have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the battery from damage.
Never store the product outside the approved temperature range of 0 °C to 45 °C.
Never charge the product outside the approved temperature range of -20 °C to 35 °C.
Never use the product outside the approved temperature range of -20 °C to 60 °C.

(charger)

Do not use damaged lamps, chargers or power sockets to charge the lamp. Do not pull the power cord to remove the AC adapter. Only use original KSE-LIGHTS chargers. The use of other chargers may have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the accumulator from damage.
Never charge the product outside the approved temperature range from 0°C to +35°C.
The chargers may only be operated with the power supply unit supplied by KSE-LIGHTS.