FORNO Espresso FMWDR3000-24BLK 24 Inch Microwave Drawer Installation Guide

: September 24, 2024
: FORNO Espresso

Installation Guide

MODEL: FMWDR3000-24BLK

FMWDR3000-24WHT

16/01/24
dd/mm/yy

Microwave Drawer

INSTALLATION MANUAL

SPECIAL WARNING

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES AND DIMENSIONS

For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 2 and 3. See Figure 1.

UNPACKING YOUR MICROWAVE DRAWER

Remove all packing materials from inside the Microwave Drawer.DO NOT REMOVE THE WAVEGUIDE COVER which is located on the top of the Microwave Drawer.
Remove the feature sticker, if there is one .Check the drawer for any damage, such as misaligned or bent drawer, damaged drawer seals and sealing surfaces, broken or loose Microwave Drawer guides and dents inside the cavity or on the front side of the drawer. If there is any damage, do not operate the Microwave Drawer and contact your dealer or PLEASE CONTACT CUSTOMER SERVICE

info@forno.ca -1- 866-231-8893

IMPORTANT NOTES TO THE INSTALLER

Read all of the Installation Manual before installing the Microwave Drawer.
Remove all packing material before connecting the electrical supply.
Observe all governing codes and ordinances.
Be sure to leave these instructions with the consumer

IMPORTANT NOTES TO THE CONSUMER

Keep this manual with your Operation Manual for future reference.

As when using any microwave oven generating heat, there are certain safety precautions you should follow. These are listed in the Operation Manual. Read all and follow carefully.
Be sure your Microwave Drawer is installed and grounded properly by a qualified installer or service technician.

IMPORTANT SAFETY INSTRUCTIONS

WARNING if the information in this manual is not followed exactly, a fire or electrical shock may result that could cause property damage, personal injury or death.

WARNING To reduce the risk of tipping ,the Microwave Drawer must be secured by a properly installed Anti-Tip block.

This Microwave Drawer must be electrically grounded in accordance with local codes.
Make sure the wall coverings and the cabinets around the Microwave Drawer can withstand the heat generated by the Microwave Drawer.

WARNING Never leave children alone or unattended in the area where a Microwave Drawer is in use. Never leave the drawer open when the microwave is unattended.
WARNING Stepping ,leaning or sitting on the drawer may result in serious injuries and can also cause damage to the Microwave Drawer.

Do not use the Microwave Drawer as a storage space . This creates a potentially hazardous situation.
Check that the time-of-day is in the display. IF not, touch Stop/Cancel to prevent unintended use.

CLEARANCES AND DIMENSIONS

Dimensions that are shown in Figure 1 must be used. Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See Figure 3.
Contact surface must be solid and level. Pay special attention to the floor on which the Microwave Drawer will sit. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 100 pounds).
Check location where the Microwave Drawer will be installed for proper electrical supply
Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven.
Be sure that the clearance of the floor between the wall oven and the microwave drawer is a minimum of 2-inches.
The microwave interior will easily accommodate a 9″ x 13″ oblong dish or a bag of microwave popcorn.

MICROWAVE DRAWER MEASUREMENTS

Figure 1

a: Suggested electrical outlet location
b: Anti Tip block
c: Floot must support 100lbs

Figure 2

Figures 1 and 2 contain many Microwave Drawer measurements for reference when planning the drawer’s location .This Microwave Drawer can be installed below any electric or gas wall oven.
*Can also be installed using an electrical outlet in an adjacent cabinet within the area where tire provided electrical cord can reach. Power cord access hole in cabinet should be a minimum l 1/2″ diameter hole and debarred of all sharp edges.

IMPORTANT Always allow sufficient power cord length to the electrical outlet to prevent tension Always check electrical codes for requirements.

ANTI-TIP BLOCK

Figure 3

a: Anti Tip block

NORMAL INSTALLATION STEPS ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS

To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located 14 13/16-inches above the floor on which the Microwave Drawer will sit. The 6-inch Anti-Tip block must be provided by the installer. See Figures 1 and 3. The Anti-Tip block prevents serious injury that might result from spilled hot liquids.
If the Microwave Drawer is ever moved to a different location, the Anti-Tip block must also be moved and installed , When installed to the wall make sure that the screws completely penetrate the dry wall and are secured in wood or metal so that the block is totally stable. When fastening, be sure that the screws do not penetrate electrical wiring or plumbing.

ELECTRICAL OUTLET

Figure 4

a: Suggested electrical outlet location

The electrical requirements are a 120 VAC 60 Hz, only,15 amp. or more protected electrical supply. It is recommended that a separate circuit serving only this appliance be provided.
The drawer is equipped with a 3-prong grounding plug, It must be plugged into a wall receptacle that is properly installed and grounded. Should you only have 2-prong outlet, have a qualified electrician install a correct wall receptacle.
Note: If you have any questions about the grounding or electrical Instructions, consult a qualified electrician or service person.

*Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach.
Always check electrical codes ,for requirements.

GROUNDING INSTRUCTIONS

This appliance must be grounded. The Microwave Drawer is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.

WARNING _ Improper use of the grounding plug can result in a risk of electric shock . Do not use an extension cord .If the power supply cord is too short ,have a qualified electrician or serviceman install an outlet near the appliance.

DRAWER INSTALLATION

Figure 5

1: Mounting flange
2: Screws

Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet.
Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall.
Slide the drawer all the way until the mounting flange is flush with the face of the cabinet. See Figure 5.
Open the drawer. Using the 4 holes on the drawer as a template , pre drill the cabinet using a 1/16″ bit. See Figure 5.
Secure the drawer with the 4 screws supplied. See Figure 6.

4 Screws
Figure 6