KSE-LIGHTS 6003 Series Cap Lamp Instruction Manual
- October 30, 2023
- KSE-LIGHTS
Table of Contents
KSE-LIGHTS 6003 Series Cap Lamp
Overview
CAP LAMP
6003-PERFORMANCE
KS-6003
| 20/45/70 lumens
---|---
| 15/30/55 meters
| 30/45/70 hours
| 420 lumens BOOST MODE
| light mode #1
light mode #2
light mode #3
| IP68
| <3 hours charging
| 3 color signal light
6003-POWER
| 70/130/260 lumens
---|---
| 55/100/200 meters
| 10/5/2,5 hours
| 420 lumens BOOST MODE
| light mode #1
light mode #2
light mode #3
| IP68
| <3 hours charging
| 3 color signal light
SIGNAL LIGHT
The signal light is switched on by pressing the button for a longer time (~3sec.). Further pressing will cycle through the available light colors. Another long press switches the main light on again.
BOOST MODE
The boost mode switches on by pressing the button for ~5sec. After 30 seconds, the light reverts back.
FIRST USE
The cap lamp must be fully charged before first use. To do this, connect the charger to a suitable power source and plug the charger into the charging port on the light.
Now a red charging status LED in the lamp will light up constantly. This
diode signals an active charging process. As soon as the charging process is
completed, the red LED goes out and a green LED lights up constantly.
The lamp is now fully charged. Please read the safety regulations regarding
charging.
After the lamp has been fully charged, the lamp can be switched on using the on/off switch.
By pressing the switch several times, the individual modes are switched through as described. After the last mode, the lamp switches off.
The lamp has a display that indicates the current battery level. The
display is always activated for 15 seconds after the lamp is switched off. The
battery status is divided into 3 levels: green= > 70% orange= >30 to 70%
red= <30
To determine the battery status as accurately as possible, leave the light on
for at least 10 seconds.
The lamp may be used and recharged at any time without negatively affecting the battery.
If the lamp is connected to the charger when it is switched on, the emergency light function is activated. When the charging process starts, the light goes out. If the mains voltage is now disconnected, the light switches on automatically and thus ensures an illuminated environment during the emergency situation.
The lamp is resistant to oil, grease, glue, hydrocarbon, turpentine
substitute and various cleaning agents.
Wash the lamp body and the windscreen with lukewarm soapy water. Do not use
acid or abrasive cleaners, especially not on the windscreen.
Do not use a high-pressure hose! Technical maintenance or repair may only be carried out by KSE-LIGHTS or an authorized person.
KSE-LIGHTS gives a two-year warranty on the product for material and manufacturing defects. Excluded from the guarantee are normal wear and tear, oxidation, changes, improper use, storage and maintenance as well as damage caused by negligence or use for which the product is not intended.
The warranty on the accumulator is limited to one year. If the serial number is removed, the warranty is immediately void. Customer service in the event of a warranty claim, please return the lamp to the dealer with proof of purchase. It will be repaired or replaced.
Do not open the lamp or charger under any circumstances. Do not use or recharge the lamp if it is defective. No warranty claims can be made for consequential damage caused by defective parts. Failure to do so will invalidate the warranty and the operational safety.
KSE-LIGHTS accepts no liability for direct, indirect and accidental consequences, as well as any other form of damage due to the use of this product.
SAFETY INFORMATIONS (cap lamp)
Do not use damaged lamps, chargers, or sockets, to charge the lamp.
Do not pull on the power cord to remove the AC adapter.
Use only original KSE-LIGHTS chargers. The use of other chargers can have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the battery from damage.
Never store the product outside the approved temperature range of 0 °C to 45 °C.
Never charge the product outside the approved temperature range of -20 °C to 35 °C.
Never use the product outside the approved temperature range of -20 °C to 60 °C.
CHARGER KS-5300
- connect the cap-lamp with the charging cable as shown in the figure. The charge status LED in the light will turn red. As soon as the status LED of the charger lights green, the cap lamp is fully charged.
- Make sure that the cable is not under tension and is fully inserted into the cap-lamp.
- the cap-lamp can be charged and recharged at any time.
KS-5300
AC 110 – 230V , 50/60Hz incl. EU/UK/AU/US
SAFETY INFORMATIONS (charger)
er sockets to charge the lamp. Do not pull the power cord to remove the AC adapter. Only use original KSE-LIGHTS chargers. The use of other chargers may have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE- LIGHTS.
Protect the charger and the accumulator from damage.
Never charge the product outside the approved temperature range from 0°C to
+35°C.
The chargers may only be operated with the power supply unit supplied by KSE-
LIGHTS.
Costumer Support
Thüngenfeld 8
58256 Ennepetal
Germany
+49 (0)2333 982 47 30
www.shop.kse-lights.com
www.kse-lights.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>