KSE-LIGHTS KS-8890 Hand Lamp User Manual
- October 30, 2023
- KSE-LIGHTS
Table of Contents
User manual for model KS-8890
KS-8890 Hand Lamp
Flashlight for use in hazardous locations
Read these instructions before use and maintain the flashlight for reference
Product:
KS-8890 Industrial Flashlight for use in hazardous locations.
Battery types:
Use only battery types below:
Alkaline Type
Energizer E91
Duracell MN1500
Rayovac AL-AA
Varta 4906
Features:
- Intrinsically safe for use in hazardous locations
- Multiple functions: High / Low
- Cree LED
- IP54
- Tough and durable casing
- Non-Slip Handle
- Safety Lock
- Built-in gas release vent
Certifications:
| Class I Div 1&2 Grp ABCD
Class II Div 1&2 Grp EFG
Class III Temperature Code: T4 IP54
File number: 261379
---|---
| Gas: Ex ia IIC T4 Ga
Mine: Ex ia I Ma
IECEx SIR 15.0062X
| Gas: II 1G Ex ia IIC T4 Ga
Mine: I M1 Ex ia I Ma
Sira 15ATEX2166X
****| 2813
DAY SUN TECHNOLOGY LTD
Address: 1stFL, No.1, Alley 2, Lane 110, Sec.4, Hsimen Rd.
North District, Tainan, 704 Taiwan
Standards:
- UL 913 7th Edition, 2011-09.23
- CSA C22.2 No. 157-92, Reaffirmed 2012
- EN 60079-0 : 2009 Edition
- EN 60079-11 : 2007 Edition
- EN 60079-26 : 2007 Edition
- IEC 60079-0, 5th Edition
- IEC 60079-11, 5th Edition
- IEC 60079-26, 2nd Edition
Installation:
**Operation:
**
Lighting by pushing the switch of KS-8890, by turning it on for two multiple functions of Full Lighting / Half Lighting and turn it off as well.
Safety Warnings:
- The screw shall be secured tightly after opening and closing of the enclosure.
- Substitution of components may impair intrinsic safety.
- Clean the flashlight only with damp cloth to avoid static electricity.
- Do not flash the light beam directly into human’s eyes.
- Always use this flashlight by following regular and legal rules governed by industrial control and management authority from every country.
Change of batteries:
Warning – Replace batteries only in non-hazardous areas.
Please loosen the two screws of the rear cover and pull it off carefully.
Remove the battery tray and fill it according to the polarity markings. Insert
the filled battery slide with the springs first into the luminaire housing.
Please make sure that the plastic nose at the end of the slide is facing the
side of the lamp switch. Replace the back cover and secure it with the two
screws.
Always use the correct batteries, please do not mix different battery brands.
Always replace all batteries at the same time.
Observe the following rules when doing so:
- Use only battery type of Energizer E91 or Duracell MN1500 or Rayovac AL-AA or Varta 4906.
- To reduce the risk of explosion do not mix used batteries with new batteries, or mix batteries from different manufacturers or from different types.
- Remove the batteries when unused for a period of time to prevent battery leakage in the device.
Warning: The screw should be secured tightly after replacing the batteries.
Declaration of Conformity
This declaration certifies compliance with the indicated directives but
implies no assurance of properties.
The safety of the product information should be observed.
Ths statement tums off automatically whenever changes are made to the product
that have not been matched with the company KSE-LIGHTS GmbH.
KSE-LIGHTS GmbH
Thingenfeld 8
58256 Ennepetal
Germany| Tel: +49 (0)2333-98247 30
Fax +49 (0)2333-98247 49
www.kse-lights.com
[email protected]| Bankverbindung:
Sparkasse Ennepetal Breckerteld
IBAN:O£62 4545 1060 0000 0927 67
Swift/BIC: WELADEDIENE| Geschaftsfihrer: Detlev Seel / Nikolai Seel
WEEE-Reg.-Nr.DE 270 590 52
Registergencht Hagen HRB /36/
Ust-Id Nr: DE 814 691 073
---|---|---|---
KSE-LIGHTS GmbH
Thüngenfeld 8, 58256 Ennepetal, Germany
Tel.: +49 2333 98247 30 • Mail:[email protected]