JUUKO B0134 RF Transceiver Module User Manual
- June 6, 2024
- JUUKO
Table of Contents
JUUKO B0134 RF Transceiver Module
Product Description
The B0134 RF Transceiver Module is a compact surface-mounted module for multi- channel Rola operation in the 2400 MHz ISM band. The module is completely shielded and pre-certified for operation under US radio regulations for license-free use.
Technical data
| Frequency | 2.4GHz |
|---|---|
| Modulation method | RoLa |
| Channel bandwidth | 500KHz |
| Supply voltage | 1.8-3.7 Volt |
| Temperature range | -40°C+85°C |
| Dimensions | 30.38×18.5×7.45(mm) |
| FCC ID | RN489896162-B0134 |
Theory of Operation/Technical Description
-
RF circuit function
The major part of this IC is a 2401-2478 MHz compliant transceiver. -
RF signal flow
The Control signal is encoded into a Data Stream to be the modulation input for the transceiver. -
Description of Antenna system
The antenna shall be connected to the RF pin. The RF pin is matched to 50 Ohm. If the antenna connector is placed away from the module at the motherboard, the track between the RF pin and the connector should be a 50 Ohm transmission line.
Block Diagram
Pin Assignment
The final host product must be submitted to SHUN HU Technology Co., Ltd. for confirmation that the installation of the module into the host is in compliance.
Mechanical Drawing
Antenna gain: 2dBi
FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
The module has received Federal Communications Commission (FCC) CFR47 Telecommunications, Part 15 Subpart C “Intentional Radiators” modular approval in accordance with Part 15.212 Modular Transmitter approval. Modular approval allows the end user to integrate the module into a finished product without obtaining subsequent and separate FCC approvals for intentional radiation, provided no changes or modifications are made to the module circuitry. Changes or modifications could void the user’s authority to operate the equipment.
The end user must comply with all of the instructions provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance.
The finished product is required to comply with all applicable FCC equipment authorizations regulations, requirements and equipment functions not associated with the transmitter module portion. For example, compliance must be demonstrated to regulations for other transmitter components within the host product; to requirements for unintentional radiators (Part 15 Subpart B “Unintentional Radiators”), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the nontransmitter functions on the transmitter module (i.e., Verification, or Declaration of Conformity) (e.g., transmitter modules may also contain digital logic functions) as appropriate.
LABELING AND USER INFORMATION REQUIREMENTS
The B0134 module has been labeled with its own FCC ID number, and if the FCC
ID is not visible when the module is installed inside another device, then the
outside of the finished product into which the module is installed must also
display a label referring to the enclosed module.
This exterior label can use wording as follows:
Contains Transmitter Module FCC ID:RN489896162-B0134 or Contains FCC ID:
RN489896162-B0134
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation
A user’s manual for the finished product should include the following statement:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Additional information on labeling and user information requirements for Part 15 devices can be found in KDB Publication 784748 available at the FCC Office of Engineering and Technology (OET) Laboratory Division Knowledge Database (KDB) http://apps.fcc.gov/oetcf/kdb/index.cfm.
RF EXPOSURE
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provided with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>