KSE Lights FSL-15 LED Mamba Instructions
- October 30, 2023
- KSE-LIGHTS
Table of Contents
LED MAMBA
MANUAL
ROOM LAMP
FSL-15 & FSL-25 & FSL-50
FSL-15 LED Mamba
| LED-MAMBA15M
FSL-15| | LED-MAMBA25M
FSL-25| | LED-MAMBA50M
FSL-50
---|---|---|---|---|---
| 22500
LUMENS| | 37 5 00
LUMENS| | 75000
LUMENS
| 15
METERS| | 25
METERS| | 50
METERS
| 180
WATTS| | 300
WATTS| | 600
WATTS
| 4
KILOGRAMS| | 6
KILOGRAMS| | 14
KILOGRAMS
| IP66
WITHOUT PLUG| | IP66
WITHOUT PLUG| | IP66
WITHOUT PLUG
| IP44
WITH PLUG| | IP44
WITH PLUG| | IP44
WITH PLUG
AFTER SALES SERVICE
The warranty of this product is valid for two years after purchasing. The time
of warranty starts with the date on purchase invoice. The warranty extends
over material defects or dysfunctions that are not caused by improper use. In
case of guarantee please fill out the customer service form full and return
this together with lamp and a copy of the purchase invoice to the local
distributor. The lamp will be repaired, or a replacement will be issued.
Secondary damage caused using the lamp with broken parts are not covered by
the warranty. In case of misuse, the warranty will be invalidated.
For the following conditions we will repair the product at appropriate charge:
- Beyond the warranty time.
- If lamp has been damaged by improper operation.
- If lamp has been cracked or damaged by impact.
- Secondary damages caused by the use with broken parts (such as broken housing or switch rubber)
EXPANDABLE UP TO 75M
| DO NOT BEND THE LIGHT TUBE EXCESSIVELY (DIAMETER >7CM)
---|---
| DO NOT FOLD THE LIGHT TUBE
| DO NOT BEND THE LIGHT TUBE HORIZONALY
| DO NOT PUT EXCESSIVE PRESSURE ON THE SURFACE
SAFETY INSTRUCTIONS
- Do not cover this product as the covering may cause the flexible light to overheat, melt, or ignite.
- Do not operate the flexible light while it is coiled. To prevent overheating do not allow contact between flexible light cables and parts of light cables. Maintain at least 12 mm spacing between flexible light cables or parts of light cables.
- Do not puncture, cut, shorten, or splice the flexible lighting.
- Do not route the cord or flexible lighting through walls, doors, windows, or any like part of the building structure.
- Do not use if there is any damage to the light or cord insulation. Inspect periodically.
- Do not submerge flexible light in liquids or use the product in the vicinity of standing water or other liquids.
- Do not install in cabinets, tanks or enclosures of any kind.
- Do not subject flexible lighting to continuous flexing.
- DO NOT EXCEED THE MAXIMUM NUMBER OF EXTENSIONS OR FLEXIBLE LIGHT LENGTHS PERMITTED BY THE MARKING.
- Do not secure this product or its cord with staples, nails or like means that may damage the insulation or permanently attach to the building structure.
- Follow instructions carefully when splicing flexible light sections or attaching power cords. Ensure that all connections, including the end cap on the last segment are properly installed with dielectric grease and shrink tube to preclude the entrance of water (outdoor applications).
- The product may not be used in explosive atmospheres.
WARNING
- These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC).
To reduce the risk of fire, electric shock or injury to persons, make sure that the electrical power to the fixture is disconnected at the source prior to installation or any servicing.
PROPER DISPOSAL (EU ONLY)
Never place any electric tools in your household refuse. To comply with European Directive 2012/19/EU concerning old electric and electronic equipment and its implementation in national laws, old electric tools must be separated from other waste and disposed of in an environment friendly fashion, e.g., by taking to a recycling depot. Recycling alternative to the demand to return electrical devices: As an alternative to returning the electrical device, the owner is obliged to cooperate in ensuring that the device is properly recycled if ownership is relinquished. This can also be done by handing over the used device to a returns center, which will dispose of it in accordance with national commercial and industrial waste management legislation. This does not apply to the accessories and auxiliary equipment without any electrical components which are inclu ded with the used device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>