KSE-LIGHTS KS 6800 Cap Lamp Instruction Manual

: October 30, 2023
: KSE-LIGHTS

Table of Contents

KSE-LIGHTS KS 6800 Cap Lamp
Product Information
Product Usage Instructions
Description
Symbol

KSE-LIGHTS KS 6800 Cap Lamp

Product Information

The KS-6800 Cap Lamp is an LED helmet light designed for use in Zone 0/21 hazardous environments. It is manufactured by KSE-LIGHTS GmbH and conforms to the ATEX and EMV directives of the European Union. The lamp comes with a charger that has charging contacts and a status LED. The cap lamp has an on/off button, LED, reflector, and helmet clip. It can be charged and recharged anytime without adversely affecting the accumulator. The product should not be used with damaged lamps, chargers, or sockets and only original KSE-LIGHTS chargers should be used.

Product Usage Instructions

First Use:

Insert the cap lamp in the charger as shown in the picture. The status LED in the charger lights red.
Ensure that there are no objects between the charger and the cap lamp.
The cap lamp can be charged and recharged anytime.

Safety Information:

Do not use damaged lamps, chargers, or power sockets to charge the lamp.
Do not pull the power cord to remove the AC adapter.
Only use original KSE-LIGHTS chargers.
The use of other chargers may have a negative effect on the life of the product. KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.

Description

Symbol

First Use

The cap lamp must be fully charged before first use. To do this, connect the charger to a suitable power source and push the lamp into the charger. Make sure that the lamp is fully inserted into the charger. When the lamp is correctly connected to the charger, an indicator LED in the lamp will light up red. The LED on the charging cup indicates the charging status. The charging current switches off automatically when the battery is fully charged. Charging is only permitted in non-hazardous areas! Only use original KSE-LIGHTS chargers! After the lamp has been fully charged, the lamp can be switched on using the on/off switch. By pressing the switch several times, the individual modes are switched through as described. After the last mode, the lamp switches off. The lamp may be used and recharged at any time without negatively affecting the battery. The lamp is resistant to oil, grease, glue, hydrocarbon, turpentine substitute and various cleaning agents. Wash the lamp body and the windscreen with lukewarm soapy water. Do not use acid or abrasive cleaners, especially not on the windscreen. Do not use a high-pressure hose! Technical maintenance or repair may only be carried out by KSE-LIGHTS or an authorized person.

KSE-LIGHTS gives a two-year warranty on the product for material and manufacturing defects. Excluded from the guarantee are normal wear and tear, oxidation, changes, improper use, storage and maintenance as well as damage caused by negligence or use for which the product is not intended. The warranty on the accumulator is limited to one year. If the serial number is removed, the warranty is immediately void. Customer service in the event of a warranty claim, please return the lamp to the dealer with proof of purchase. It will be repaired or replaced. Do not open the lamp or charger under any circumstances. Do not use or recharge the lamp if it is defective. No warranty claims can be made for consequential damage caused by defective parts. Failure to do so will invalidate the warranty and the operational safety. KSE-LIGHTS accepts no liability for direct, indirect and accidental consequences, as well as any other form of damage due to the use of this product.

Connection

Cap lamp

Insert the cap lamp in the charger as shown in the picture. The status LED in the charger lights red.
Please make sure, that there are no objects between the charger and the cap lamp.
The cap lamp can be charged and recharged anytime.

SAFETY INFORMATION

Do not use damaged lamps, chargers or sockets to charge the lamp.
Never place the switched-on lamp on the light window when working in potential dangerous atmosphere.
Do not pull the power cord to remove the plug out of the socket.
Only use original KSE-LIGHTS chargers.
The use of other chargers may adversely affect the life of the product.
KSE-LIGHTS is not responsible for consequential damage, if parts are used which are not authorized by KSELIGHTS.
Protect the charger and accumulator from damage.
Never store the products outside the approved temperature range from 0°C to +45°C.
Never charge the product outside of the approved temperature range from -20°C to +35°C.
Never use the product at temperature range from -15°C to +50°C.
Do not use damaged lamps, chargers or power sockets to charge the lamp.
Do not pull the power cord to remove the AC adapter.
Only use original KSE-LIGHTS chargers.
The use of other chargers may have a negative effect on the life of the product.
KSE-LIGHTS is not liable for consequential damage if parts are used which are not approved by KSE-LIGHTS.
Protect the charger and the accumulator from damage.
Never charge the product outside the approved temperature range from 0°C to +35°C.
The chargers may only be operated with the power supply unit supplied by KSE-LIGHTS which has the following characteristics.
If a charger should be supplied with voltage by other means, the voltage source must have one of the following characteristics:
SELV or PELV system, where the output voltage does not exceed 50 VAC or 120 VDC
Safety isolating transformer that meets the requirements of IEC 61558-2-6 or a technically equivalent standard.
Directly with a power supply according to IEC 60950, IEC 61010-1 or a technically equivalent standard.
Directly from cells or batteries, provided the cell voltage is the same.

TROUBLESHOOTING

When using the cap lamp and charging adapter some malfunctions or operator failures can appear, here are the solutions:
The cap lamp can not be turned on.
Insert the lamp into the charger and try again. Should the Lamp still show no response, please contact our product service.
The lamp shows no response to insertion in the charger.
Disconnect the charger from the supply voltage and try again. Should the lamp still show no reaction, please contact our product service.

KSE-LIGHTS