RYNOSKIN RSSS-JL2D-54 Running Boards Installation Guide

: June 13, 2024
: RYNOSKIN

Table of Contents

RYNOSKIN RS-JL2D-54 Running Boards
Product Information
Part List
Product Usage Instructions
Features
Torque & Tools
BEFORE INSTALLATION
Part List
TOOLS
INSTALLATION INSTRUCTION
Documents / Resources

RYNOSKIN RS-JL2D-54 Running Boards

RYNOSKIN RSSS-JL2D-54 Running Boards-PRODUCT

Product Information

Product Name: Python Side Step
Part Number: RSSS-JL2D-54
Fits: 2018-Up Jeep Wrangler JL 2 Door
Installation Time: 90-180 minutes
Cutting Required: No
Drilling Required: No

Part List

Driver Side Front Support Bracket (x4)
Passenger Side Front Support Bracket (x8)
Driver Side Rear Support Bracket (x4)
Passenger Side Rear Support Bracket (x8)
Passenger Side Rear Bracket (x4)
10mm x 30mm Hex Bolt (x8)
10mm x 24mm Flat Washer (x8)
10mm Lock Nut (x4)
8mm x 25mm Combo Bolt (x8)
8mm Lock Washer (x4)
8mm x 28mm Flat Washer (x8)
6mm x 25mm Hex Bolt (x16)
6mm x 22mm Flat Washer (x4)
8mm x 35mm Hex Bolt (x8)
6mm Lock Nut (x4)

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
6mm| 7-8.5| 10mm| 4mm
8mm| 18-20| 13mm| 5mm
10mm| 35-40| 16mm| 6mm
12mm| 60-70| 18mm| 8mm

Product Usage Instructions

BEFORE INSTALLATION

Remove contents from the box and verify all parts are present according to the Part List.
Read the instructions carefully.
Cutting may be required, so assistance is recommended.

STEP 1

Start installation on the Passenger/Right front of the vehicle. Find the front threaded insert located in between the first pair of holes along the pinch weld.

STEP 2

Select the Passenger/Right Front Mounting Bracket. Attach the Mounting Bracket to the threaded insert using (1) 8mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer. Do not tighten the hardware.

STEP 3:

Attach the Passenger/Right Front Support Bracket to the Mounting Bracket using (1) 10mm Hex Bolt, (2) 10mm Flat Washers, and (1) 10mm Nylon Lock Nut. Also, attach the Passenger/Right Front Support Bracket to the pinch trim using (2) 6mm Hex Bolts, (4) 6mm Flat Washers, and (2) 6mm Nylon Lock Nuts.

STEP 4:

Move to the rear mounting location and locate the threaded insert and pair of holes in the pinch weld. Repeat Steps 2 & 3 to attach the Passenger/Right Rear Mounting Bracket and Passenger/Right Rear Support Bracket. Do not tighten the hardware.

Features

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required| Allen Wrench Required
---|---|---|---
■   6mm| ■           7-8.5|
| ■ 10mm| ****| □ 4mm
■   8mm| ■          18-20| ■ 13mm| □ 5mm
■    10mm| ■          35-40| ■ 16mm| □ 6mm
□ 12mm| □ 60-70| □ 18mm| □ 8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM THE BOX. VERIFY ALL PARTS ARE PRESENT DEPENDING ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. CUTTING MAY BE REQUIRED. ASSISTANCE IS RECOMMENDED.

Part List

RYNOSKIN RSSS-JL2D-54 Running Boards-
FIG-3

TOOLS

RYNOSKIN RSSS-JL2D-54 Running Boards-FIG-4

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER-SIDE INSTALLATION

INSTALLATION INSTRUCTION

STEP 1

Start installation on the Passenger/Right front of the of the vehicle. Find the front threaded insert located in between the first pair of holes along the pinch weld, (Fig 1).
(Fig 1) Passenger/Right side front mounting location with threaded insert

STEP 2

Select the Passenger/Right Front Mounting Bracket. IMPORTANT: Please identify the Front and Rear Brackets according to the illustration on the Part List. Attach the Mounting Bracket to the threaded insert using (1) 8mm Hex Bolt, (1) 8mm Lock Washer, and (1) 8mm Flat Washer, (Fig 2). Do not tighten the hardware.
(Fig 2) Attach the Passenger/Right Front Mounting Bracket to the front location

STEP 3

Select the Passenger/Right Front Support Bracket.
IMPORTANT: Please identify the Front and Rear Support Brackets according to the I illustration on the Part List. Attach the Support Bracket to the pinch weld using (2) 6mm Hex Bolts, (4) 6mm Flat Washers, and (2) 6mm Nylon Lock Nuts, (Fig 3).
NOTE: Insert Bolts from the outside of the pinch weld, (Fig 4). Attach the Support Bracket to the Mounting Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers, and (1) 10mm Nylon Lock Nut, (Figs 5 – 6). Do not tighten the hardware.
( Fig 3) Attach the Passenger/Right Front Support Bracket to the pinch trim
( Fig 4) Insert Bolts from the outside of the pinch weld.
(Fig 5) Attach the Passenger/Right Front Support Bracket to the Mounting Bracket
(Fig 6) Passenger/Right front mounting bracket and support bracket attached.

STEP 4

Move to the rear mounting location and locate the threaded insert and pair of holes in the pinch weld, (Fig 7). Repeat Steps 2 & 3 to attach the Passenger/Right Rear Mounting Bracket and Passenger/Right Rear Support Bracket, (Figs 8 – 10).
IMPORTANT: The Rear Brackets have an Oblique Cut on their top surface. Please identify the Front and Rear Mounting Brackets and Support Brackets according to the illustration on the Part List. Do not tighten the hardware.
(Fig 7) Passenger/Right rear mounting location
(Fig 8) Passenger/Right Rear Mounting Bracket with an Oblique Cut on its top
( Fig 9) Attach the Passenger/Right Rear Bracket and PS passenger/Right Rear Support Bracket to the rear location
(Fig 10) Passenger/Right rear mounting bracket and support bracket attached.

STEP 5

Select the Passenger/Right Running Board.
NOTE: The Passenger/Right Running Board will have a “54-P” on the front. Attach the Running Board to the Mounting Brackets with (4) 8mm Combo Bolts, (Fig 11).
IMPORTANT: Do not slide the Running Board on the Mounting Bracket cradles, or damage to the finish may result. Do not tighten the hardware.
(Fig 11) Attach the Passenger/Right Running Board to the Mounting Brackets

STEP 6

Level and adjust the Running Board and tighten all hardware.

STEP 7

Repeat Steps 1—6 to attach the Driver/Left Running Board.

STEP 8

Do periodic inspections of the installation to make sure that all hardware is secure and tight.

Attention

To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.
Customer Support:service@rynoskinauto.com
www.rynoskinauto.com