RYNOSKIN RSFB-JK0002 Stubby Front Bumper Instruction Manual

June 1, 2024
RYNOSKIN

STUBBY FRONT BUMPER INSTALLATION INSTRUCTIONS
PART NO. RSFB-JK0002

RSFB-JK0002 Stubby Front Bumper

Fits:
2007-2018 Wrangler JK/2018-2024 Jeep Wrangler JL (Excl. Rubicon/plug-in hybrid models/2021-2024 V8 engine)/ 2020-2024 Jeep Gladiator(Excl. Mojave trim)
90-180 min Installation time is different according to individual person.
Cutting Not Required
Drilling Not Required

TOOLS REQUIRED

RATCHET SOCKET SET
TORQUE WRENCH
TRIM PANEL REMOVAL TOOL
ALLEN WRENCH (PROVIDED)
DO NOT OVER TORQUE. PLEASE FOLLOW THE TIGHTEN OPERATING LOAD STANDARD BELOW:
6mm BOLTS & NUTS: FROM 7 TO 8.5 FOOT POUND.
8mm BOLTS & NUTS: FROM 18 TO 20 FOOT POUND.
10mm BOLTS & NUTS: FROM 35 TO 40 FOOT POUND.
12mm BOLTS & NUTS: FROM 60 TO 70 FOOT POUND.
RYNOSKIN RSFB-JK0002 Stubby Front Bumper - MILD SOAP TO PROTECT YOUR INVESTMENT, DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES THAT COULD DAMAGE THE FINISH. MILD SOAP MAY BE USED TO CLEAN THE PRODUCT.

PARTS LIST:

Description Qty Image Remark
Bumper 1
Light Bar Mount 1
Block Off Plates 2
Fog Light Brackets 2
Foam Protection Plate 2
D-Rings 2
M10 x 1.5 x 35mm Hex Bolts 10
M10 x 1.5 x 25mm Button Head Bolts 6 Use the provided S=6 allen wrench to

tighten
M10 Lock Washers| 14| |
M10 Flat Washers| 20| |
M10 Nuts| 10| |
M4 x 0.7 x 15mm Button Head Bolts| 12| | Use the provided
S=2.5 allen wrench to tighten
M4 Lock Washers| 12| |
M4 Flat Washers| 20| |
M4 Nuts| 8| |
S=6 Allen Wrench| 1| | Use for 10mm
hardware
S=2.5 Allen Wrench| 1| | Use for 4mm
hardware

RYNOSKIN RSFB-JK0002 Stubby Front Bumper - STUBBYRYNOSKIN RSFB-JK0002 Stubby Front Bumper - STUBBY
1

PROCEDURE:

  1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. FACTORY INSTALLED OR AFTERMARKET FRONT BUMPERS MUST BE REMOVED.
  2. Remove the (6) plastic push pins securing the factory splash shield to the vehicle: (4) Across the front edge, (2) on the rear edge. (Figures 1 )
  3. From under the vehicle, remove the factory fog light connectors and free the fog light wiring loom from the bumper. (Figures 2 )
  4. From under the vehicle, access and remove the (8) 18mm nuts securing the factory bumper to the vehicle. (Figures 3 )
  5.  Remove the 2 push pins holding the top cover onto the vehicle. (Figures 4 )
  6. Remove the (8) 7mm screws securing the foglights to the factory front bumper. (Figures 5 )
  7. Install the fog light bracket using(6)M4 Bolts,(10)M4 Flat Washers,(6)M4 Lock Washers, and (4)M4 Nuts. Repeat this process for both fog lights. (Figures 6 )
  8. Install the bumper to the frame of the vehicle using (4) M10x35mm bolts, (8) M10 flat washers, (8) M10 lock washers, and (4) M10 nuts. Torque to 40 ft-lbs. (Figures 7 )
  9. Install the optional light bar mount by using (2) foam protection plate, (6) M10 x 35mm bolts ,(12) M10 Flat Washers,(6) M10 Lock Washers, (6) M10 Nuts. (Figures 8 )
  10. If user doesn’t need the light bar, then install the (2) block off plates to the bumper by using the (6) M10 x 25mm button head bolts, (12) M10 Flat Washers,(6) M10 Lock Washers, (6) M10 Nuts. (Figures 9 )
  11. Install the D-Ring brackets to the bumper. Plug the factory fog light harness into the fog lights. Installation is complete. (Figures 10 )

Installation Pictured

(Fig 1) Remove the (6) plastic push pins securing the factory splash shield to the vehicle RYNOSKIN RSFB-JK0002 Stubby Front Bumper - splash
shield(Fig 2) From under the vehicle, remove the factory fog light connectors and free the fog light wiring loom from the bumper.
(Fig 3) From under the vehicle, access and remove the (8) 18mm nuts securing the factory bumper to the vehicle.
RYNOSKIN RSFB-JK0002 Stubby Front Bumper - securing(Fig 4) Remove the 2 push pins holding the top cover onto the vehicle. RYNOSKIN RSFB-JK0002 Stubby Front Bumper -
holding(Fig 5) Remove the (8) 7mm screws securing the fog lights to the factory front bumper. (Fig 6) Install the fog light using(6)M4 Bolts,(10)M4 Flat Washers,(6)M4 Lock Washers, and(4)M4 Nuts. Repeat the process for both fog lights. RYNOSKIN RSFB-JK0002 Stubby Front Bumper -
fog light using

(Fig 7) Install the bumper to the frame of the vehicle using (4) M10x35mm bolts, (8) M10 flat washers, (8) M10 lock washers, and (4) M10 nuts. Torque to 40 ftlbs.RYNOSKIN RSFB-JK0002 Stubby Front Bumper - bumper
2(Fig 8) Install the optional light bar mount by using (2) foam protection plate, (6) M10 x 35mm bolts ,(12) M10 Flat Washers,(6) M10 Lock Washers, (6) M10 Nuts. RYNOSKIN RSFB-JK0002 Stubby
Front Bumper - light 1(Fig 9) If user doesn’t need the light bar, then install the (2) block off plates to the bumper by using the (6) M10 x 25mm button head bolts, (12) M10 Flat Washers,(6) M10 Lock Washers, (6) M10 Nuts. (Fig 10) Install the D-Ring brackets to the bumper. Plug the factory fog light harness into the fog lights. Installation is complete.

www.rynoskinauto.com
4/22/22 (LS)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals