RYNOSKIN RS-JSS-020 Running Boards Instruction Manual

June 13, 2024
RYNOSKIN

Rocker Step
PART NO. RS-JSS-020 FITS: 2007-2018 Jeep Wrangler JK 4 Door

RS-JSS-020 Running Boards

RYNOSKIN RS-JSS-020 Running Boards - fig 1

Torque & Tools

Fastener Size| Tightening Torque (ft-Ibs)| Wrench Required| Allen Wrench Required
---|---|---|---
■ 6mm| ■ 7-8.5| RYNOSKIN RS-JSS-020 Running Boards - fig
2| ■ 10mm| | ❑4mm
■ 8mm| ■ 18-20| ■ 13mm| | ❑5mm
■ 10mm| ■ 35-40| ■ 16mm| ❑6mm
❑12mm| ❑60-70| ❑18mm| ❑8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.

Part List

RYNOSKIN RS-JSS-020 Running Boards - Part ListRYNOSKIN RS-JSS-020 Running Boards - Part List
1

PLEASE NOTE THAT THE FOLLOWING PICTURES ARE BASED ON THE PASSENGER SIDE INSTALLATION
STEP 1
Start installation toward the front of the Passenger/Right side of the vehicle, Locate the front, center and rear mounting locations (Fig 1).RYNOSKIN RS-JSS-020 Running Boards - fig 4
(Fig 1) Passenger/Right mounting locations
STEP 2
Determine if the vehicle has an open floor panel or a threaded hole in the floor panel
(1) Vehicles with open mounting location:
a. Insert (1) 10mm Nut Plate into the large square opening in the floor panel. Line up the threaded nut with the hole in between the pair of holes on the pinch weld, (Fig 2).
b. Select the Passenger/Right Front Mounting Bracket. NOTE: There is a small notch at the Bottom of the Center Brackets and the notch of Rear Brackets is at the Top. Please identify the Front, Center and Rear Brackets according to the Part List.
c. Attach the Bracket to the Nut Plate with (1) 10mm x 35mm Hex Bolt, (1) 10mm Lock Washer and (1) 10mm x 34mm Flat Washer, (Fig 3). Do not tighten hardware.
(2) Vehicles with factory threaded hole in floor panel:
a. Select the Passenger/Right Front Mounting Bracket. Attach the Bracket to the front mounting location (Fig 4) with (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Fig 5). Do not tighten hardware.RYNOSKIN RS-
JSS-020 Running Boards - fig 5

(Fig 2) Passenger/Right front mounting location (Models open mounting location shown)RYNOSKIN RS-JSS-020 Running Boards - fig 6(Fig 3) Attach the Passenger/Right Front Mounting Bracket to the Nut Plate RYNOSKIN RS-JSS-020 Running Boards - fig 7(Fig4) Passenger/Right front mounting location (Models with threaded insert shown) RYNOSKIN RS-JSS-020 Running Boards - fig 8(Fig5) Attach the Passenger/Right Front Mounting Bracket to the Threaded Hole

STEP 3
Select (1) Passenger/Right Support Bracket (#2). Attach the Support Bracket to the pinch weld with (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Fig 6).RYNOSKIN RS-JSS-020 Running Boards - fig
9(Fig 6) Attach (1) Passenger/Right Support Bracket (#2) to the (2) holes in the pinch trim in the front location
STEP 4
Attach the Support Bracket to the Mounting Bracket with (1) 10mm x 30mm Hex Bolt, (2) 10mm x 20mm Flat Washers and (1) 10mm Nylon Lock Nut, (Fig 7). Do not tighten hardware. RYNOSKIN RS-JSS-020 Running Boards - fig
10(Fig 7) Attach (1) Passenger/Right Support Bracket (#2) to the Front Mounting Bracket
STEP 5
Repeat Steps 2 – 4 to attach the Passenger/Right Center and Rear Mounting Brackets and Support Brackets to the center and rear locations, (Figs 89). NOTE: There is a small notch at the Bottom of the Center Brackets and the notch of Rear Brackets is at the Top. Please identify the Center and Rear Brackets according to this, (Fig 10). Do not tighten hardware. RYNOSKIN RS-
JSS-020 Running Boards - fig 11(Fig 8) Passenger/Right center mounting location (Model with open mounting location shown) RYNOSKIN RS-JSS-020 Running Boards - fig 12(Fig 9) Passenger/Right rear mounting location (Model with threaded inset shown)RYNOSKIN RS-JSS-020 Running Boards - fig 13(Fig 10) Differentiate the Center and Rear Brackets
STEP 6
Select the Passenger/Right Rocker step.
NOTE: The Passenger/Right Rocker step will have a “20-R” on the front. Attach the Rocker step to the Mounting Brackets with (6) 8mm Combo Bolts, (Fig 11). IMPORTANT: Do not slide Rocker step on the Mounting Bracket cradles, or damage to the finish may result. Do not tighten hardware.RYNOSKIN RS-JSS-020
Running Boards - fig 14(Fig 11) Attach the Passenger/Right Rocker step to the Mounting Brackets
STEP 7
Level and adjust the Rocker step and tighten all hardware.
STEP 8
Repeat Steps 1—7 to attach Driver/Left Rocker step.
STEP 9
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Rocker step.

Customer Support: service@rynoskinauto.com
www.rynoskinauto.com 
Rev. 2/16/23 (JH)

Documents / Resources

| RYNOSKIN RS-JSS-020 Running Boards [pdf] Instruction Manual
RS-JSS-020 Running Boards, RS-JSS-020, Running Boards, Boards
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals