RYNOSKIN RS-FSP-001 Front Skid Plate Installation Guide

June 1, 2024
RYNOSKIN

RYNOSKIN RS-FSP-001 Front Skid Plate

Product Specifications:

  • Part Number: RS-FSP-001
  • Fits: 2021-2024 FORD BRONCO
  • Installation Time: 90-180 minutes (varies per individual)
  • Cutting Not Required
  • Drilling Not Required

Product Usage Instructions

Tools Required:

  • Wrench/Socket Set

Tightening Guidelines:
DO NOT OVER TORQUE. Follow the tightening standards below:

  • 6mm Bolts & Nuts: 7 to 8.5-foot pounds
  • 8mm Bolts & Nuts: 18 to 20 foot pounds
  • 10mm Bolts & Nuts: 35 to 40-foot pounds
  • 12mm Bolts & Nuts: 60 to 70-foot pounds

Cleaning Instructions:

To protect your investment, do not use any polish or wax-containing abrasives. Clean with mild soap only.

Installation Steps:

  1. Remove the splash guard from the model with a plastic bumper cover (refer to Fig 1).
  2. Reuse the factory hardware to attach the Skid Plate (refer to Fig 3).

Frequently Asked Questions (FAQ):

Q: How long does it take to install the front bumper skid plate?
A: The installation time varies but typically takes between 90 to 180 minutes.

Q: Do I need to cut or drill during installation?
A: Cutting and drilling are not required for installation.

Q: What tools are required for installation?
A: A wrench/socket set is needed for installation.

FRONT BUMPER SKID PLATE INSTALLATION INSTRUCTIONS
PART NO. RS-FSP-001
Fits:
2021-2024 FORD BRONCO

WARNING

  • 90-180min Installation time is different according to individual person.
  • Cutting Not Required
  • Drilling Not Required

TOOLS REQUIRED
WRENCH/SOCKET SET

DO NOT OVER TORQUE. PLEASE FOLLOW THE TIGHTEN OPERATING LOAD STANDARD BELOW:

  • 6mm BOLTS & NUTS: FROM 7 TO 8.5 FOOT POUND.
  • 8mm BOLTS & NUTS: FROM 18 TO 20 FOOT POUND.
  • 10mm BOLTS & NUTS: FROM 35 TO 40 FOOT POUND.
  • 12mm BOLTS & NUTS: FROM 60 TO 70 FOOT POUND.

TO PROTECT YOUR INVESTMENT, DO NOT USE ANY TYPE OF POLISH OR WAX THAT MAY CONTAIN ABRASIVES THAT COULD DAMAGE THE FINISH. MILD SOAP MAY BE USED TO CLEAN THE PRODUCTS.

PARTS LIST

Description Qty Image Remark
Skid Plate 1 ![RYNOSKIN-RS-FSP-001-Front-Skid-Plate-1](https://manuals.plus
/wp-content/uploads/2024/04/RYNOSKIN-RS-FSP-001-Front-Skid-Plate-1.png)

PROCEDURE

REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED.

  1. Start installation from under the front of the vehicle. Remove the splash guard from below/behind the bumper, (Figures 1 & 2).
  2. Select the Skid Plate, (Figure 3).
  3. With assistance, hold the Skid Plate up to the bottom of the vehicle. Line up the holes in the Skid Plate with the factory splash guard mounting brackets. Reuse the factory mounting bolts for the splash guard to attach the front of the Skid Plate, (Figure 3). Reuse the factory hex bolts to attach the rear of the Skid Plate to the bottom of the frame.
  4. Check the Skid Plate alignment with the vehicle and fully tighten all hardware at this time.
  5. Do periodic inspections to the installation to make sure that all hardware is secure and tight.

RYNOSKIN-RS-FSP-001-Front-Skid-Plate-2

www.rynoskinauto.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals