RYNOSKIN RS-JSS-123 Running Boards Owner’s Manual

June 13, 2024
RYNOSKIN

Rocker Step
PART NO. RS-FSS-123
FITS: 2018-Up Jeep Wrangler JL 2 Door

RS-JSS-123 Running Boards

| |
---|---|---
60-120 min| Cutting Not
Required| Drilling Not
Required

Torque & Tools

Fastener Size| Tightening Torque (ft-lbs)| Wrench Required Allen Wrench| Required
---|---|---|---
6mm| 7-8.5| | 10mm| | 4mm
8mm| 18-20| 13mm| 5mm
10mm| 35-40| 16mm| 6mm
12mm| 60-70| 18mm| 8mm

BEFORE INSTALLATION

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT DEPEND ON THE PARTS LIST. READ INSTRUCTIONS CAREFULLY. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.

Part List

RYNOSKIN RS JSS 123 Running Boards - Part List RYNOSKIN RS JSS 123 Running Boards - Part List 2

PLEASE NOTE THAT THE FOLLOWING
PICTURES ARE BASED ON THE
PASSENGER SIDE INSTALLATION

STEP 1
Start installation on the Passenger/Right front of the of the vehicle. Find the front threaded insert located in between the first pair of holes along the pinch weld, (Fig 1).

STEP 2
Select the Passenger/Right Front Mounting Bracket. IMPORTANT: Please identify the Front and Rear Brackets according to the illustration on Part List. Attach the Mounting Bracket to the threaded insert using (1) 8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Fig 2).
Do not tighten hardware.

STEP 3
Select the Passenger/Right Front Support Bracket. IMPORTANT: Please identify the Front and Rear Support Brackets according to the illustration on Part List. Attach the Support Bracket to the pinch weld using (2) 6mm Hex Bolts, (4) 6mm Flat Washers and (2) 6mm Nylon Lock Nuts, (Fig 3). NOTE: Insert Bolts from the outside of the pinch weld. Attach the Support Bracket to the Mounting Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut, (Fig 4). Do not tighten hardware.

STEP 4
Move to the rear mounting location and locate the threaded insert and pair of holes in the pinch weld, (Fig 5). Repeat Steps 2 & 3 to attach the Passenger/Right Rear Mounting racket (Fig 6) and Passenger/Right Rear Support Bracket, (Fig 7). IMPORTANT: The Rear Brackets has an Oblique Cut on its top surface. Please identify the Front and Rear Support  Brackets according to the illustration on Part List. Do not tighten hardware.

STEP 5
Select the Passenger/Right Rocker Step.
NOTE: The Passenger/Right Rocker Step will have a “23R” on the front. Attach the Rocker Step to the Mounting Brackets with (4) 8mm Combo Bolts, (Fig 8).
IMPORTANT: Do not slide Rocker Step on the Mounting Bracketcradles, or damage to the finish may result.
Do not tighten hardware.

STEP 6
Level and adjust the Rocker Step and tighten all hardware.

STEP 7
Repeat Steps 1—6 to attach Driver/Left Rocker Step.

STEP 8
Do periodic inspections to the installation to make sure that all hardware is secure and tight.

Attention
To protect your investment, do not use any type of polish or wax that may contain abrasives that could damage the finish.
Mild soap may be used also to clean the Running Boards.

www.rynoskinauto.com
Rev. 2/13/23 (JH)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals